HuddleCamHD HCM-1 Bedienungsanleitung

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für HuddleCamHD HCM-1 (2 Seiten) in der Kategorie niet gecategoriseerd. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Step 2
Screw mount to pipe securely, engag-
ing a minimum of of pipe into 1/2”
mount (Fig 4). When aligned to desired
locaon, ghten set screw (Fig 1, #2)
to 30 36 in lbs of torque (this is ap-- -
proximately when the set screw will
stop moving and the long arm of the
long arm hex wrench(Fig 1, #3) will
start to bend slightly).
What s Included
QTY —Small Ceiling Mount BK/WH1
QTY x 3/8" PPH and QTY Machine Screw Flat Washer (Fig 1, #1)1 1/4"-20 2 1/4”
QTY cup point set screw (Fig 1, #2)1 10/32 x 1/4”
QTY long arm hex wrench (for set screw) (Fig 1, #3)1 3/32”
#2
#3
Fig 1
Rev 2.1
5/15/2020
HCM-1C
Small Base Camera
Ceiling Mount
Setup Guide
Mounng Instrucons
Step 1
Screw NPT pipe, or pipe nipple, to a properly 1”
installed mounng plate or pipe ange (Fig 2).
Tighten unl pipe can no longer be ghtened with
a pipe wrench.
If using a plate or ange you must us a 1.5” 1.5” -
1” reducing bushing (Fig 3).
NOTE: Plate/ange, reducer bushing and NPT 1”
pipe or nipple are not included.
Fig 2 Fig 4
For more informaon on HuddleCamHD
mounts and other products please visit:
hps://huddlecamhd.com/ Rev 2.1
5/15/2020
HuddleCamHD
HC- -WEBCAM 94
HC-GO
HC- -EPTZ XXX
HC3X-XX-G2
HC3XA-XX
HC3XW-XX-G2
HC10X USB2- -XX
HC10XA-XX
HC10X-XX-G3
HC20X-XX-G2
Step 4 / 4
Pass cabling through pipe or dress
to outside of pipe and connect for
a clean installaon.
Mounng Instrucons Connued...
Mount Compability
Step 3 / 4
Mount camera upright to top of mount
or invert to boom of mount with includ-
ed 1/4 20 machine screw. (Fig 1, # 1) U--
lize (0,1,2) machine screw at wash-1/4”
ers as required. (Fig 1, #1) Note: 1/4”
machine screw at washers are to be
used depending upon depth of thread
insert in base of camera, in order to
achieve a snug t.
Other Cameras
This mount has been
designed for use with most
small based cameras ulizing
a 1/4 20” -mounng hole as
can be found on SONY,
Panasonic, Cisco, Polycom
and Vaddio cameras.
PTZOpcs
PT 80- -WEBCAM
PTEPTZ ZCAM-XXX-
PTVL-XXX- ZCAM
PT12X-XXX-ZCAM
PT20X-XXX- ZCAM
PT12X-XXX XX- - G2
PT20X-XXX XX- - G2
PT30X-XXX XX- - G2

Produktspezifikationen

Marke: HuddleCamHD
Kategorie: niet gecategoriseerd
Modell: HCM-1

Brauchst du Hilfe?

Wenn Sie Hilfe mit HuddleCamHD HCM-1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung niet gecategoriseerd HuddleCamHD

Bedienungsanleitung niet gecategoriseerd

Neueste Bedienungsanleitung für -Kategorien-