Hotpoint-Ariston FDG 8640BS EU Bedienungsanleitung

Hotpoint-Ariston Wasch-Trockner-Kombinationen FDG 8640BS EU

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hotpoint-Ariston FDG 8640BS EU (84 Seiten) in der Kategorie Wasch-Trockner-Kombinationen. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/84
1
GB
English,1
GB
WASHER-DRYER
! This symbol reminds you to read this instruc-
tion manual.
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and advice, 5
General safety
Disposal
Opening the porthole door manually
Description of the washer-dryer, 6-7
Control panel
Display
How to run a wash cycle or a drying cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash options
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
FDG 8640
Instructions for use
PortuguĂŞs,25
PTES
EspaĂąol,13
Magyar,37
HU
HU DE
Deutsch,49 Română,61
RO
РусскиК,73
HU
RU
2
GB
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washer-dryer.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see
figure).
Before performing
the connection, allow
the water to run freely
until it is perfectly
clear.
2. Connect the
inlet hose to the
washer-dryer by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand
side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
! This instruction manual should be kept in a
safe place for future reference. If the washer-
dryer is sold, transferred or moved, make
sure that the instruction manual remains with
the machine so that the new owner is able to
familiarise himself/herself with its operation
and features.
! Read these instructions carefully: they
contain vital information relating to the safe
installation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washer-dryer from its
packaging.
2. Make sure that the washer-dryer has not
been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4
protective screws
(used during
transportation)
and the rubber
washer with the
corresponding
spacer, located on
the rear part of the
appliance ( ).see figure
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washer-dryer needs to
be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture
cabinets or anything else.
2. If the floor is
not perfectly level,
compensate for
any unevenness by
tightening or loosening
the adjustable front
feet ( ); the see figure
angle of inclination,
measured in relation to
the worktop, must not
exceed 2°.
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor;
alternatively, placed
it over the edge
of a basin, sink or
tub, fastening the
duct supplied to
the tap ( ). see figure
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the
electricity socket, make sure that:
• thesocketisearthedandcomplieswithall
applicable laws;
• thesocketisabletowithstandthe
maximum power load of the appliance as
indicated in the Technical data table (see
opposite);
• thepowersupplyvoltagefallswithinthe
values indicated in the Technical data table
( );see opposite
• thesocketiscompatiblewiththeplugofthe
washer-dryer. If this is not the case, replace
the socket or the plug.
! The washer-dryer must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washer-dryer has been installed, the
electricity socket must remain within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
65 - 100 cm
! The power supply cable must only be
replaced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these standards
are not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using
wash cycle auto clean (see “Cleaning the
washer-dryer).
Technical data
Model FDG 8640
Dimensions
width 59.5 cm
height 85 cm
depth 60,5 cm
Capacity
from 1 to 8 kg for the wash
programme
from 1 to 6 kg for the drying
programme
Electrical
connections
please refer to the technical
data plate fixed to the machine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed up to 1400 rotations per
minute
Energy ra-
ted
programmes
according to
regulation
EN 50229
Wash: programme 4; tem-
perature 60°C; using a load
of 8 kg.
Drying: the smaller load
(2kg) must be dried by
selecting the “A1” (IRON)
dryness level. The load must
consist of 2 sheets, 1 pil-
lowcase and 1 hand towel;
the remainder of the load must
be dried by selecting the “A4”
(EXTRA) dryness level.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electromagne-
tic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU

Produktspezifikationen

Marke: Hotpoint-Ariston
Kategorie: Wasch-Trockner-Kombinationen
Modell: FDG 8640BS EU

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hotpoint-Ariston FDG 8640BS EU benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Wasch-Trockner-Kombinationen Hotpoint-Ariston

Hotpoint-Ariston

Hotpoint-Ariston FDG 8640BS EU Bedienungsanleitung

4 Juli 2024

Bedienungsanleitung Wasch-Trockner-Kombinationen

Neueste Bedienungsanleitung fĂźr -Kategorien-

Summit

Summit SPWD2200W Bedienungsanleitung

14 Oktober 2024
Bosch

Bosch WVD24520EU Bedienungsanleitung

13 Oktober 2024
Hoover

Hoover WDXOA 486AC-80 Bedienungsanleitung

13 Oktober 2024
Hoover

Hoover WDXOA496AHFN-80 Bedienungsanleitung

13 Oktober 2024
Indesit

Indesit WIDXL 146 (UK) Bedienungsanleitung

12 Oktober 2024
Hoover

Hoover WDXOA 596FN-80 Bedienungsanleitung

12 Oktober 2024
Indesit

Indesit EWDC 7145 S FR Bedienungsanleitung

12 Oktober 2024
Sanyo

Sanyo SW-160TP Bedienungsanleitung

11 Oktober 2024
Indesit

Indesit PWDE 8148 S (UK) Bedienungsanleitung

11 Oktober 2024
Siemens

Siemens WK14D542ES Bedienungsanleitung

10 Oktober 2024