Honeywell F300E1001 Bedienungsanleitung

Honeywell Nicht kategorisiert F300E1001

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Honeywell F300E1001 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

OWNER’S GUIDE

69-0756-07

F50F and F300E Electronic

Air Cleaners

CONTENTS

Operating Your Electronic Air Cleaner ....................... 2

Getting the Most From Your Electronic Air Cleaner 2

Cleaning Prefilter(s), Cell(s) and Postfilter(s) ......... 3

How Electronic Air Cleaning Works ............................. 5

Before You Call for Service .............................................. 6

Resideo 10 Year Ultraclean Coil Guarantee™ .......... 6

Limited Five-year Warranty ............................................ 7

Product Registration ......................................................... 8

M38810

F50F AND F300E ELECTRONIC AIR CLEANERS

69-0756—07 4

CAUTION

Burn Hazard.

Can cause personal injury.

Allow cell(s) to cool completely in dishwasher and

at tend of wash cycle or wear protective gloves.

Washing the cell(s) in your automatic

dishwasher

Hot water can accumulate in the tubes supporting the

collector plates.Tip the cell(s) so these tubes can drain.

IMPORTANT

• Check your dishwasher Owner’s manual. Some

manufacturers do not recommend washing elec-

tronic cell(s) in their dishwashers.

• If the dishwasher has upper and lower arms, posi-

tion the cell(s) carefully to allow good water circu-

lation.

• Be careful to avoid damaging the cell(s) when

placing them in the dishwasher. Broken ionizer

wires or bent collector plates are not covered

under the Warranty.

• Very dirty cell(s), especially from tobacco or cook-

ing smoke, can discolor the plastic parts and the

lining of some dishwashers.This discoloration is

not harmful. To minimize it, wash the cell(s) more

frequently or try a different brand of detergent.

• Do NOT allow the dishwasher to run through the

dry cycle. This bakes on any contaminants not

removed during the wash cycle and reduces air

cleaner efficiency.

1. Put the cell(s) on the lower rack of the dishwasher

with the airflow arrow pointing up. It may be neces-

sary to remove the upper rack. Do not block water

flow to the upper arm.

HINT: Lay a few large water glasses between the spikes on

the lower rack, and rest the cell(s) on them so the spikes do

not damage the aluminum collector blades.

2. Using your regular dishwashing detergent, allow the

dishwasher to run through the complete wash and

rinse cycle. Do not use the dry cycle. To avoid burns,

let the cell(s) cool completely before removing, or

wear protective gloves when removing the cell(s).

Remember that water may be trapped inside the

cell(s) plates. Tip the cell(s) so these tubes can drain.

3. Wipe the ionizer wires and contact board on the end

of the cell using your thumb and forefinger with a

small, damp cloth.

4. Inspect the dishwasher. You may want to rerun the

wash and/or rinse cycle with the dishwasher empty if

you see dirt or residue from washing the cell(s). If

dirt or residue seems excessive, wash the cell(s)

more often or try a different detergent.

CAUTION

Hazardous Chemical.

Can cause personal injury.

Do not splash detergent solution in eyes.

Washing the cell(s) in a tub

• Wear rubber gloves to avoid prolonged detergent

contact with your skin.

• Keep detergent and solution out of reach

of children.

NOTE: Always wash the cell(s) first, then the prefilter(s),

to keep heavy prefilter lint from getting caught in

the cell(s).

1. Use a large enough container, such as a laundry tub

or trash container, to hold one or both cell(s).

NOTE: Sharp corners on the cell(s) can scratch the sur-

face of a bathtub.

2. Dissolve about three-fourth cup of automatic dish-

washer detergent per cell in enough hot water to

cover the cell(s). If the detergent does not dissolve

readily, or forms a scum on the water, try another

brand, or use softened water.

3. After the detergent has completely dissolved, place

the cell(s) in the container and allow to soak for 15 to

20 minutes or until water cools. Agitate them up and

down a few times and remove. Repeat steps 2 and 3,

if necessary, for very dirty cells.

4. Next, wash the prefilter(s) the same way. Empty and

rinse the wash container.

5. Rinse the cell(s) with a hard spray of very hot water;

rinse the tub clean, then fill the tub with clean hot

water and soak for 5 to 15 minutes. Rinse until the

water draining from the cell(s) and prefilter(s) no

longer feels slippery.

6. Soak cell(s) in a final clear water rinse for ten min-

utes.

7. Wipe the ionizer wires and contact board on the end

of the cell using your thumb and forefinger with a

small, damp cloth.

Replacing electronic air cleaner

components

1. Inspect the cell(s) for broken ionizer wires and bent

collector plates. Repair, as necessary, or call your

contractor for service.

2. Slide the prefilter(s) into the upstream prefilter

guides.

3. Slide the air cleaner cell(s) in so the air flow arrow

points downstream and the handle(s) face outward.

4. Firmly close the access door.

5. Turn on the air cleaner. If the cell(s) and prefilter(s)

are wet, the neon light may not come on and you

may hear arcing. If the arcing is annoying, simply

turn the air cleaner off for two to three hours or until

the cell(s) are dry.

F50F AND F300E ELECTRONIC AIR CLEANERS

69-0756—07 6

Electronic air cleaner vs standard furnace

filter

The regular furnace filter collects mainly large, visible

particles that reach the filter. Its main purpose is to protect

the furnace and air conditioner blower. The electronic air

cleaner collects these large particles plus many of the

smaller, mostly invisible particles. Its purpose is to reduce

indoor air pollution as well as to protect the blower, air

conditioning coils and heat exchanger.

Ozone and the electronic air cleaner

Electronic air cleaners generate a very small amount of

ozone, about 0.005 to 0.010 parts per million (ppm). The

amount is highest when the air cleaner is new.

The average person can detect the odor of ozone in

concentrations as low as 0.003 to 0.010 ppm. The U.S.

Food and Drug Administration, and Health and Welfare

Canada recommend that indoor ozone concentration

should not exceed 0.050 ppm. As a comparison, the

outdoor ozone level in major cities is sometimes higher

than 0.100 ppm.

If desired, the ozone generated by the air cleaner can be

reduced by asking your dealer to:

• Install an activated carbon filter downstream of the air

cleaner, or

• Adjust the air cleaner power supply to reduce ozone

production.This adjustment reduces ozone production

about 20-25 percent, but also reduces air cleaning

efficiency about seven to ten percent.

About lint or “white dust"

White dust is made up of particles that settle out of the air

before they get to the return air duct. You can help prevent

this white dust from settling by running your fan

constantly and:

• Be sure the return registers are not blocked with

furniture.

• Be sure the discharge ducts are clean (best done before

installing the air cleaner).

• Be sure your clothes dryer is vented to the outside and

is not plugged.

• If you have new rugs or drapes or new woolen blankets,

be aware that the lint from these items will reduce with

age.

• In new or remodeled homes, plaster dust or paint

pigment may contribute to white dust, but will reduce

with time.

• Use of a humidifier may contribute to white dust,

especially if filled with undistilled water.

BEFORE YOU CALL FOR

SERVICE

If...

Then...

Electronic air cleaner doesn't seem to be working

1. Make sure the furnace or air conditioner blower is

running.

2. Make sure the access door is firmly closed and

latched. If door is not closed properly, an interlock

keeps the air cleaner off.

Arcing (snapping) seems too frequent

1. If the electronic cell(s) are wet from washing, turn

the air cleaner off for two to three hours.

2. Check the cell(s) for broken ionizer wires or bent

plates. Repair if necessary.

3. Wash cell(s) and prefilter(s) if dirty.

Neon light on air cleaner does not come on

1. Make sure the furnace or air conditioner fan is run-

ning.

2. Make sure the access door is firmly closed.

3. Make sure the On-Off switch is in the On position.

4. On models without the Solid State Performance

Indicator, if the electronic cell(s) are wet, check again

in two to three hours.

You smell ozone and find it objectionable

Call your heating and air conditioning dealer.

RESIDEO 10 YEAR UltraClean

COIL GUARANTEE™

Guarantee

If you properly maintain your

new Resideo Electronic Air

Cleaner (EAC), Resideo

guarantees that if your indoor

coil requires cleaning within the

next 10 years, Resideo will pay

to have it professionally cleaned by a qualified contractor:

— 75% of the cost (up to $150) when installed with a

Resideo Coil Irradiation Ultraviolet Air Treatment

System or

— 50% of the cost (up to $100) if a Resideo EAC is

installed without a Resideo Coil Irradiation Ultraviolet

Air Treatment System).

• The UltraClean Coil Guarantee™ applies to any Resideo

Electronic Air Cleaner properly installed with a heat

pump, air conditioner or high efficiency furnace that is:

brand new, less than one year old; or more than one

year old with the indoor coil professionally cleaned by a

qualified contractor prior to installation.

• Proper maintenance on the EAC means: keep the power

switch in the On position, periodically verify power

operation, and wash electronic cells periodically as

specified in this Owner’s Guide.

• Proper maintenance on the Electronic Air Cleaner

means: periodically clean the lamp glass and replace

UV lamps as specified in the Owner’s Guide.

Send to:

Resideo 10 Year

UltraClean Coil Guarantee

Customer Care, MN10-1461

1885 Douglas Drive North

Golden Valley, MN 55422

Produktspezifikationen

Marke:	Honeywell
Kategorie:	Nicht kategorisiert
Modell:	F300E1001

Brauchst du Hilfe?

Wenn Sie Hilfe mit Honeywell F300E1001 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Honeywell

Honeywell RCHTSENSOR-1PK/U Bedienungsanleitung

26 August 2024

Honeywell TrueZONE HZ432 Bedienungsanleitung

15 August 2024

Honeywell Evohome HR92WE Bedienungsanleitung

11 August 2024

Honeywell F300B2012 Bedienungsanleitung

8 August 2024

Honeywell CN51 Bedienungsanleitung

6 August 2024

Honeywell HCS80 Bedienungsanleitung

6 August 2024

Honeywell F100F2044/U Bedienungsanleitung

5 August 2024

Honeywell F100F1625/U Bedienungsanleitung

5 August 2024

Honeywell EvoHome THR99C3102 Bedienungsanleitung

4 August 2024

Honeywell 42206395 Bedienungsanleitung

4 August 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024