Honeywell F300B2012 Bedienungsanleitung

Honeywell Nicht kategorisiert F300B2012

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Honeywell F300B2012 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/6

OWNER’S GUIDE

69-0756-07

F50F and F300E Electronic

Air Cleaners

CONTENTS

Operating Your Electronic Air Cleaner ....................... 2

Getting the Most From Your Electronic Air Cleaner 2

Cleaning Prefilter(s), Cell(s) and Postfilter(s) ......... 3

How Electronic Air Cleaning Works ............................. 5

Before You Call for Service .............................................. 6

Resideo 10 Year Ultraclean Coil Guarantee™ .......... 6

Limited Five-year Warranty ............................................ 7

Product Registration ......................................................... 8

M38810

F50F AND F300E ELECTRONIC AIR CLEANERS

69-0756—07 2

OPERATING YOUR

ELECTRONIC AIR CLEANER

GETTING THE MOST FROM

YOUR ELECTRONIC AIR

CLEANER

Run the electronic air cleaner as much as

possible

For greatest efficiency, the air cleaner should run all the

time. To do this, set the Fan switch on your thermostat to

On, and make sure the air cleaner is turned on. The fan

and air cleaner run even when the furnace or air

conditioner is off.

NOTE: A manual fan switch may be built into the furnace

or furnace fan controller.

The air cleaner uses less power than a 40 watt light bulb

(two-cell model—33 watts; single cell model—22 watts).

Many believe that the added cost is more than offset by

the added benefits of full-time air cleaning and full-time

air circulation. And you may feel that the room

temperature stays more even when the fan is always on.

Even if your thermostat does not have a Fan On position,

you can obtain maximum available air cleaning benefit by

making sure the air cleaner is always turn to On so it

operates whenever the furnace or air conditioner is on.

Keep the cell(s) and prefilter(s) clean

Although the air cleaner is designed to be efficient over a

wide range of cell dirt loading conditions, regular cleaning

is your best assurance of consistent performance. Also, a

very dirty prefilter and cell reduces air flow and, in turn,

this reduces the efficiency of the furnace or air

conditioner.

Replace postfilter regularly

A high-efficiency postfilter is sometimes installed in the

air cleaner. This filter increases the efficiency of the air

cleaner and should be changed every six months of usage.

If you have a humidifier

All Resideo whole house humidifiers can be used in a

system with the Resideo Electronic Air Cleaner without

any additional filters or system modification.

If your system includes an atomizing humidifier, you may

want to install a standard furnace filter between the

humidifier and the air cleaner.This filter would keep the

humidifier spray mineral deposits from collecting on the

air cleaner.This filter should be checked regularly and

changed when it shows signs of mineral or dirt buildup. If

you do not install a filter, you will probably need to wash

the cell(s) and prefilter(s) more often to remove the

mineral buildup.

If an ultrasonic room humidifier is used often, especially if

filled with tap (undistilled) water, the cell(s) and prefilter(s)

require more frequent washing. A white residue

accumulates on the cell(s) from the minerals in the water.

This residue may also contribute to "white dust.” See About

lint or “white dust” section for more information.

Turn the On-Off switch on the power

box to On.

NOTE: Set the switch to 1 for On

and set the switch to O for

Off.

The air cleaner now operates

whenever your furnace/air

conditioning system fan operates.

For maximum air cleaning benefit

and cleaner air conditioner coils,

leave the air cleaner switch turned

on at all times and the thermostat

fan switch set to On. Of course,

continuous fan operation adds to

your electric bill each month. Check

your equipment for the amount of

electricity needed to run your

System fan.

When the fan and air cleaner come

on, the neon indicator lights.

You may hear a snapping (electrical

arcing) sound occasionally as the air

cleaner operates. This is usually

caused by a larger dust particle that

causes a high voltage discharge.The

snapping sound means that your air

cleaner is working as it should.To

hear the snapping sound,

momentarily press the test button

near the botton of the door. Use the

test button any time you want to

prove air cleaner operation.

The switch remains in the On

position to keep the air cleaner

running.

When the fan and air cleaner stops,

the neon light goes off. The air

cleaner is off until the heating or air

conditioning and fan start again.

If you do not want the air cleaner to

run, set the On-Off switch to Off to

turn off the air cleaner. Your furnace

and air conditioner continue to

operate normally, but without the

added benefit of air cleaning.

Normally, this switch should be turn

to On at all times.

M3584A

M3586A

M6032A

M3585A

M3583A

F50F AND F300E ELECTRONIC AIR CLEANERS

69-0756—07 4

CAUTION

Burn Hazard.

Can cause personal injury.

Allow cell(s) to cool completely in dishwasher and

at tend of wash cycle or wear protective gloves.

Washing the cell(s) in your automatic

dishwasher

Hot water can accumulate in the tubes supporting the

collector plates.Tip the cell(s) so these tubes can drain.

IMPORTANT

• Check your dishwasher Owner’s manual. Some

manufacturers do not recommend washing elec-

tronic cell(s) in their dishwashers.

• If the dishwasher has upper and lower arms, posi-

tion the cell(s) carefully to allow good water circu-

lation.

• Be careful to avoid damaging the cell(s) when

placing them in the dishwasher. Broken ionizer

wires or bent collector plates are not covered

under the Warranty.

• Very dirty cell(s), especially from tobacco or cook-

ing smoke, can discolor the plastic parts and the

lining of some dishwashers.This discoloration is

not harmful. To minimize it, wash the cell(s) more

frequently or try a different brand of detergent.

• Do NOT allow the dishwasher to run through the

dry cycle. This bakes on any contaminants not

removed during the wash cycle and reduces air

cleaner efficiency.

1. Put the cell(s) on the lower rack of the dishwasher

with the airflow arrow pointing up. It may be neces-

sary to remove the upper rack. Do not block water

flow to the upper arm.

HINT: Lay a few large water glasses between the spikes on

the lower rack, and rest the cell(s) on them so the spikes do

not damage the aluminum collector blades.

2. Using your regular dishwashing detergent, allow the

dishwasher to run through the complete wash and

rinse cycle. Do not use the dry cycle. To avoid burns,

let the cell(s) cool completely before removing, or

wear protective gloves when removing the cell(s).

Remember that water may be trapped inside the

cell(s) plates. Tip the cell(s) so these tubes can drain.

3. Wipe the ionizer wires and contact board on the end

of the cell using your thumb and forefinger with a

small, damp cloth.

4. Inspect the dishwasher. You may want to rerun the

wash and/or rinse cycle with the dishwasher empty if

you see dirt or residue from washing the cell(s). If

dirt or residue seems excessive, wash the cell(s)

more often or try a different detergent.

CAUTION

Hazardous Chemical.

Can cause personal injury.

Do not splash detergent solution in eyes.

Washing the cell(s) in a tub

• Wear rubber gloves to avoid prolonged detergent

contact with your skin.

• Keep detergent and solution out of reach

of children.

NOTE: Always wash the cell(s) first, then the prefilter(s),

to keep heavy prefilter lint from getting caught in

the cell(s).

1. Use a large enough container, such as a laundry tub

or trash container, to hold one or both cell(s).

NOTE: Sharp corners on the cell(s) can scratch the sur-

face of a bathtub.

2. Dissolve about three-fourth cup of automatic dish-

washer detergent per cell in enough hot water to

cover the cell(s). If the detergent does not dissolve

readily, or forms a scum on the water, try another

brand, or use softened water.

3. After the detergent has completely dissolved, place

the cell(s) in the container and allow to soak for 15 to

20 minutes or until water cools. Agitate them up and

down a few times and remove. Repeat steps 2 and 3,

if necessary, for very dirty cells.

4. Next, wash the prefilter(s) the same way. Empty and

rinse the wash container.

5. Rinse the cell(s) with a hard spray of very hot water;

rinse the tub clean, then fill the tub with clean hot

water and soak for 5 to 15 minutes. Rinse until the

water draining from the cell(s) and prefilter(s) no

longer feels slippery.

6. Soak cell(s) in a final clear water rinse for ten min-

utes.

7. Wipe the ionizer wires and contact board on the end

of the cell using your thumb and forefinger with a

small, damp cloth.

Replacing electronic air cleaner

components

1. Inspect the cell(s) for broken ionizer wires and bent

collector plates. Repair, as necessary, or call your

contractor for service.

2. Slide the prefilter(s) into the upstream prefilter

guides.

3. Slide the air cleaner cell(s) in so the air flow arrow

points downstream and the handle(s) face outward.

4. Firmly close the access door.

5. Turn on the air cleaner. If the cell(s) and prefilter(s)

are wet, the neon light may not come on and you

may hear arcing. If the arcing is annoying, simply

turn the air cleaner off for two to three hours or until

the cell(s) are dry.

Produktspezifikationen

Marke:	Honeywell
Kategorie:	Nicht kategorisiert
Modell:	F300B2012

Brauchst du Hilfe?

Wenn Sie Hilfe mit Honeywell F300B2012 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Honeywell

Honeywell RCHTSENSOR-1PK/U Bedienungsanleitung

26 August 2024

Honeywell TrueZONE HZ432 Bedienungsanleitung

15 August 2024

Honeywell Evohome HR92WE Bedienungsanleitung

11 August 2024

Honeywell F300B2012 Bedienungsanleitung

8 August 2024

Honeywell CN51 Bedienungsanleitung

6 August 2024

Honeywell HCS80 Bedienungsanleitung

6 August 2024

Honeywell F100F2044/U Bedienungsanleitung

5 August 2024

Honeywell F100F1625/U Bedienungsanleitung

5 August 2024

Honeywell EvoHome THR99C3102 Bedienungsanleitung

4 August 2024

Honeywell 42206395 Bedienungsanleitung

4 August 2024

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024