Hogue Monogrip Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hogue Monogrip (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
MONOGRIP
®
ASSEMBLY
INSTRUCTIONS
If you have any problems installing
your MONOGRIP please call us at
(805) 239-1440. We will be glad to
help make sure your grip fits perfectly.
Please use these instructions as a
general guide. Due to the large
number of different firearm frame
styles, your particular installation may
be slightly different. Please look for
any supplemental instructions that
may be included in your package. If
you have any problems, do not
hesitate to contact us.
HOGUE® INC.
P.O. BOX 91360
HENDERSON, NV 89009
1-800-438-4747
Hogueinc.com
CRD_INS_R1_03212017
4
5
Mate the firearm handle and MONOGRIP
®
by rst placing
the stirrup and stock pin into the internal guide grooves using
your thumb to spread the grip.
MONOGRIP® should be guided up behind the trigger guard,
then pivoted to cover the frame straps. The grip must mate
with the semi-circular loops at the top of the gun handle.
MONOGRIP® must be fully seated on the frame before
inserting mounting screw.
2Place the stirrup over the bottom strap of the handle and
rotate it until the hole in each side engages the stock pin.
1Before starting to work, MAKE SURE THE FIREARM IS
UNLOADED. Remove existing grips.
When in place, the stirrup is a clamp that provides a screw
thread hanging below the handle for securing the
MONOGRIP® to the frame. No alternation of the firearm
frame is needed. Remove the screw from the stirrup.
6
3
7
Insert the mounting screw through the hole on the bottom of
the grip. Insert the screw so it enters the stirrup threads, and
using an appropriate screwdriver, tighten the screw until snug,
no tighter. Over-tightening does nothing to increase grip
tightness and can damage the screw or stirrup.
Your MONOGRIP® is designed to fit an average size firearm
frame. However, frame dimensions do vary slightly from
firearm to firearm. If necessary, your MONOGRIP
®
can be
adjusted by placing small shim(s) of tape (as shown) on the
lower corner of the front strap. Add or subtract tape until grip
is flush with backstrap.
IMPORTANT!
Check all functions of your firearm after grips are installed.
Test fire your firearm.
®
A FEW WORDS ABOUT FIT
It is a fact that gun frame dimensions
vary from firearm to firearm. No grip is
shipped unless it fits and functions on our
firearms properly. Please keep this in mind.
It is imperative to make sure that every
firearm functions properly with after-market
grips installed. Although the grip functions
properly on our firearms, it is the users
responsibility to check all functions of a
firearm after new grips are installed. This is
especially important if the weapon is to be
used for law enforcement duty. If you do
not feel competent to check the proper
function yourself, we suggest visiting your
gunsmith to check this for you.
It is important to test fire the firearm
before using in the field.
IMPORTANT CONSUMER AND
WARRANTY INFORMATION ON
BACK OF PACKAGE
If any parts are missing Hogue will supply them at no charge.
NOTE: Dan Wesson, Taurus Tracker or Judge and Ruger LCR Models do not require stirrup assembly.
Simply guide the firearm handle into the Monogrip and fully seat the frame. Insert the mounting screw through the
bottom of the grip into the frame threads. Do not over tighten.
* **
* Stirrup is not provided nor
needed for Dan Wesson,
Taurus Tracker or Judge and
Ruger LCR Models.
** Screw is not provided with
Taurus Tracker & Judge
models.


Produktspezifikationen

Marke: Hogue
Kategorie: Nicht kategorisiert
Modell: Monogrip

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hogue Monogrip benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Hogue

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-