Hobbywing XRotor micro 20A BLHeli Bedienungsanleitung

Hobbywing Funkgesteuertes Spielzeug XRotor micro 20A BLHeli

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hobbywing XRotor micro 20A BLHeli (1 Seiten) in der Kategorie Funkgesteuertes Spielzeug. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/1

Others

Programmable Items

• F396 chip for great performance , 48MHz .

• BLHeli open-source program implemented in the ESC supports all BLHeli functions like ESC programming and firmware upgrade via the throttle control signal cable.

• Small size combined with light weight for easy installation.

• Compatible with “Regular” signal-receiving mode and “OneShot” signal-receiving mode (that is the ESC can receive fixed throttle signals range from 125µs~250µs).

• The twisted-pair design of the throttle signal cable effectively reduces the crosstalk produced in signal transmission and makes flight more stable.

• Compatible with various flight-controllers and supports a signal frequency of up to 500Hz in “Regular”signal-receiving mode.

Thank you for purchasing this HOBBYWING product! Brushless power

systems can be very dangerous. Any improper use may cause personal injury

and damage to the product and related devices. We strongly recommend

reading through this user manual before use. Because we have no control

over the use, installation, or maintenance of this product, no liability may be

assumed for any damage or losses resulting from the use of the product. We

do not assume responsibility for any losses caused by unauthorized

modifications to our product.

We, HOBBYWING, are only responsible for our product cost and nothing else

as result of using our product.

• Read through the manuals of all power devices and aircraft and ensure the power configuration is rational before using this unit, as incorrect configuration may cause the ESC to overload

and be damaged.

• Ensure all wires and connections must be well insulated before connecting the ESC to related devices, as short circuit will damage your ESC. And ensure all devices are well connected,

(please use a soldering iron with enough power to solder all input/output wires and connectors if necessary,) as poor connection may cause your aircraft to lose control or other

unpredictable issues such as damage to the device.

• Do not use this unit in the extremely hot weather or continue to use it when it gets really hot (around 105 /221 ). Because high temperature will cause the ESC to work abnormally or ℃ ℉

even damage it.

• Users must always disconnect the batteries after use as the current on the ESC is consuming continuously if it`s connected to the batteries (even if the ESC is tur ned off). The battery will

completely be discharged and may result in damage to the battery or ESC when it is connected for a long period of time. This will not be covered under warranty.

IMP OR T ANT

Throttle Range Calibration

Once

1. Power up:

Once

2. Throttle up detected

(arming sequence start):

Once

7. Throttle calibration is finished:

While

measuring

3. Zero throttle detected (arming sequence end):

Once

1. Power up:

Once

2. Throttle up detected

(arming sequence start):

While

measuring

3. Zero throttle detected (arming sequence end):

While

measuring

5. When throttle is below midstick (measuring min throttle):

Once

4. If throttle is above midstick for 3 seconds:

This beep sequence indicates that max throttle has been stored

Attention!

. This operation is only applicable to

code revision 14.4 and later.

. There is no such beep sequence for

prior code revisions. Users need to

disconnect the battery from the ESC,

and then reconnect it to the ESC.

Once

6. If throttle is below midstick for 3 seconds：

This beep sequence indicates that min throttle has been stored This beep sequence indicates the throttle

calibration is finished, and the ESC is ready to go.

This is an extremely powerful brushless motor system. We strongly recommend removing your propellers for your own safety and the safety of those around you

before performing calibration and programming functions with this system.

ESC Programming

While

measuring

5. When throttle is below midstick (measuring min throttle):

Once

4. If throttle is above midstick for 3 seconds:

This beep sequence indicates that max throttle has been stored

Once

7. Full throttle detected after the throttle stick is moved to the top position:

This beep sequence indicates that programming mode is entered.

Enter

programming

mode

Once

6. If throttle is below midstick for 3 seconds：

This beep sequence indicates that min throttle has been stored

Once

8. Beeps - Programming mode"

Function 1, parameter value 1

Once

Function 1, parameter value 2

Once

Function 2, parameter value 1

Parameter value stored

...etc...

If the throttle stick is moved to zero during one of the above sequences,

the parameter value of that function is selected and stored. And you will hear this sound:

The ESC then resets itself.

IMP OR T ANT

Illustration：

Long beep

Short beep

Maximum Volume

Minimum Volume

It will be more convenient if users adjust

parameters via BLHeli Suite (configuration

software).

Model

XRotor micro 20A BLHeli

XRotor micro 30A BLHeli

XRotor micro 35A BLHeli

Cont. Current

20A

30A

35A

Peak Current (10sec)

30A

40A

50A

BEC

LiPo

2-4S

3-6S

Weight

6.8g

9.5g

Size

24.0 x 13.9 x 5.5 mm

36.5 x 16.7 x 5.5 mm

Motor Wiring

Normal Start-up Process

Once

1. Power up:

Once

2. Throttle up detected

(arming sequence start):

Once

3. Zero throttle detected

(arming sequence end):

4. After this, the motor will run.

UBEC

Motor

Receiver

Battery

Electronic

Speed

Controller

(Those “gray background and black text” options are the factory default settings.)

*: Only enabled for some ESCs. From code rev 14.4, damped light is default on the ESCs that support it. For prior code revisions, high is default.

**: Default startup power varies by ESC. Generally the default power is lower for larger ESCs.

If for some reason there is an error in the eeprom/flash write operation (e.g. due to loss of power or low voltage), defaults will be loaded.

1. Closed Loop P Gain: it sets the proportional gain for the rpm control loop.

This setting controls the gain from speed error to motor power.

2. Closed Loop I Gain: it sets the integral gain for the rpm control loop.

This setting controls the gain from integrated speed error (summed over time) to motor power.

3. Closed Loop Mode: it sets the range of speeds that the control loop can operate on.

• For the high range, throttle values from 0% to 100% linearly correspond to rpm targets from 0 to 200000 electrical rpm.

• For the middle range, throttle values from 0% to 100% linearly correspond to rpm targets from 0 to 100000 electrical rpm.

• For the low range, throttle values from 0% to 100% linearly correspond to rpm targets from 0 to 50000 electrical rpm.

When closed loop mode is set to Off, the control loop is disabled.

4. Multi Gain: it scales the power applied to the motor for a given input.

Note that this is only for PWM input, for PPM input it has no effect. Beware that a low multi gain will also limit the maximum power to the motor.

5. Startup Power: it is always done with the direct startup method, which runs the motor using back emf detection from the very start.

In this mode power is given by the throttle used, but limited to a maximum level. This maximum level can be controlled with the startup power parameters. Beware that setting startup

power too high can cause excessive loading on ESC or motor.

6. Commutation Timing: it can be adjusted in five steps.

Low is about 0°, mediumlow 8°, medium 15°, mediumhigh 23° and high 30°.

Typically a medium setting will work fine, but if the motor stutters it can be beneficial to change the timing.

7. PWM Frequency

High pwm frequency is around 20kHz, and low pwm frequency is around 8kHz.

Pwm damped light mode: it adds loss to the motor for faster retardation and it always uses high pwm frequency. It is only supported on some ESCs where fet switching is sufficiently fast.

8. PWM Dither: it’s a parameter that adds some variation to the motor pwm off cycle length. This can reduce problems (like throttle steps or vibration) in rpm regions where the pwm

frequency is equal to harmonics of the motor commutation frequency, and it can reduce the step to full throttle. It is primarily beneficial when running damped light mode, Dither is not

applied in closed loop mode.

9. Demag Compensation: it’s a feature to protect from motor stalls caused by long winding demagnetization time after commutation. The typical symptom is motor stop or stutter upo quick

throttle increase, particularly when running at a low rpm. As described earlier, setting high commutation timing normally helps, but at the cost of efficiency.

Generally, a higher value of the compensation parameter gives better protection.

If demag compensation is set too high, maximum power can be somewhat reduced.

10. Rotation Direction: it can be used to reverse motor rotation.

11. Input PWM Polarity: it can be used to inverse the throttle behavior and it’s intended to be used with receivers that provide negative pwm (at least some Walkeras do).

When using PPM input it must be set to positive.

Programming parameters that can only be accessed from configuration software (BLHeliSuite):

• Throttle minimum and maximum values for PPM input (will also be changed by doing a throttle calibration).

•

Throttle center value for bidirectional operation with PPM.

•

Beep strength, beacon strength and beacon delay.

•

Programming by TX. If disabled, the TX can not be used to change parameter values (default is enabled).

•

Thermal protection can be enabled or disabled (default is enabled).

•

(The motor power will be reduced to 75% when its temperature exceeds 140 ; the power will be reduced to 50% when the temperature is above 145 ; the power will be reduced to 25% ℃ ℃

when the temperature goes above 150 ; and the pwoer will be reduced to 0% if the temperature exceeds 155 .) ℃ ℃

•

PWM input can be enabled and disabled (default is disabled). If disabled, only 1-2ms PPM and 125-250µs OneShot125 are accepted as valid input singals. Set to disabled if using OneShot125

with looptimes below 1100.

•

Power limiting for low RPMs can be enabled or disabled (default is enabled). Disabling it can be necessary in order to achieve full power on some low KV motors running on a low supply

voltage. However, disabling it increases the risk of toasting motor or ESC.

Closed loop P gain

Closed loop I gain

Closed loop mode

Multi gain

Startup power**

Commutation timing

Pwm frequency

Pwm dither

Demag compensation

Rotation direction

Input pwm polarity

0.13

HiRange

0.75

0.031

Low

High

Off

Normal

Positive

0.17

MidRange

0.88

0.047

MediumLow

Low

Reversed

Negative

Function 3

0.25

LoRange

1.00

0.063

Medium

DampedLight*

High

Bidirectional

0.38

Off

1.12

0.094

MediumHigh

0.50

1.25

0.125

High

0.75

0.188

1.00

0.25

1.5

0.38

2.0

0.50

3.0

0.75

4.0

1.00

6.0

1.25

8.0

1.50

BLHeli official website https://github.com/bitdump/BLHeli：

BLHeliSuit download https://www.mediafire.com/folder/dx6kfaasyo24l/BLHeliSuite：

This BLHeli ESC Firmware XRotor 20A Multi BLHeli Rev 14.4：（）：

Warnings

Features

Specifications

User Guide

CA UT IONS

AT T ENT ION

Introduction

USER MANUAL

Multi-Rotor

XRotor micro 20A/30A/35A BLHeli

Brushless Electronic Speed Controller

If the throttle stick is moved below max (but not to zero), the current parameter will be

skipped, and programming will proceed to the next parameter. This way it is possible to

access the later parameters without going through all the beeps.

It is generally a good idea to go to full throttle again before selecting a parameter, to

make sure you have selected the right parameter.

Throttle is read in the 1 second pause between the function/parameter beeps.

If the throttle stick is never moved to zero, the ESC will load the defaults and then reset

itself after the last parameter value of the last function. This is a convenient way of

setting all parameters to defaults.

If power is disconnected during the programming sequence, then no changes are done to

the programmed values.

20161227

Produktspezifikationen

Marke:	Hobbywing
Kategorie:	Funkgesteuertes Spielzeug
Modell:	XRotor micro 20A BLHeli

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hobbywing XRotor micro 20A BLHeli benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Funkgesteuertes Spielzeug Hobbywing

Hobbywing XeRun XR10 Pro WP Bedienungsanleitung

25 September 2024

Hobbywing XeRun XR10 Stock Spec G2 Bedienungsanleitung

25 September 2024

Hobbywing XeRun XR10 Justock G3S Bedienungsanleitung

25 September 2024

Hobbywing XeRun XR8 PRO G3 Bedienungsanleitung

25 September 2024

Hobbywing XeRun XR10 Justock G3 Handout Bedienungsanleitung

25 September 2024

Hobbywing XeRun XR8 Plus G2S Bedienungsanleitung

25 September 2024

Hobbywing XeRun XR10 Pro 1S Heavy Duty Bedienungsanleitung

25 September 2024

Hobbywing XeRun XR10 Stock Spec 1S Bedienungsanleitung

25 September 2024

Hobbywing XeRun XR10 PRO 160A Bedienungsanleitung

25 September 2024

Hobbywing Xerun V10 G3 Bedienungsanleitung

5 September 2024

Bedienungsanleitung Funkgesteuertes Spielzeug

Neueste Bedienungsanleitung für -Kategorien-

Proline Trencher Bedienungsanleitung

4 Oktober 2024

Futaba 12Z Bedienungsanleitung

4 Oktober 2024

Graupner 33718.XT60 Bedienungsanleitung

3 Oktober 2024

Amewi Hyper Go Bedienungsanleitung

1 Oktober 2024

Carson Drift Burner Bedienungsanleitung

1 Oktober 2024

Carson Micro X-Warrior 2.0 Bedienungsanleitung

1 Oktober 2024

Biltema 45-8119 Bedienungsanleitung

1 Oktober 2024

Traxxas Stampede Bedienungsanleitung

29 September 2024

Spektrum DX2E 2Ch DSMR Surface Radio w/SR310 Bedienungsanleitung

23 September 2024

Futaba SKYSPORT_4YBF Bedienungsanleitung

17 September 2024