Hobbywing UBEC 5A HV (3-10S) Bedienungsanleitung

Hobbywing Funkgesteuertes Spielzeug UBEC 5A HV (3-10S)

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hobbywing UBEC 5A HV (3-10S) (1 Seiten) in der Kategorie Funkgesteuertes Spielzeug. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/1
User Manual of 5A HV－
－
－
－－UBEC HW-SM811DUL-20130412
- 1 -
5 Amps High Voltage Switch Mode UBEC
1. Why do you need a high voltage UBEC?
The 5A-HV-UBEC is a switch-mode DC-DC regulator supplied with a 3S to 10S Lipo battery pack
and outputs a consistent safe power for your receiver, gyro and servos. It is very suitable for big
electric RC models such as fixed-wing aircrafts and helicopters which use more than 4 cells lithium
battery.
Using this UBEC, the receiver can obtain the power supply directly from the main battery pack, so
the additional battery pack for receiver is unnecessary.
Compared with the linear mode UBEC, the overall efficiency of the switch-mode UBEC is much
higher, so it can extend the working time of the receiver battery pack, and because a switch mode
UBEC can significantly reduce the heat emission, it can avoid the loss of control caused by the
over-heat problem which is frequently happened with the linear mode UBEC.
2. Specification:
2.1. Output Voltage: 5V or 6V (Changeable with an jumper )
2.2. Continuous output current: 5 Amps
2.3. Burst output current: 7.5 Amps
2.4. Input: 8V-42V (3-10 cells lithium battery pack)
2.5. Quiescent current: 20mA
2.6. Size: 48mm*27mm*9mm (length*width*height)
2.7. Weight: 30g
3. Features:
3.1. Designed with an advanced switch mode DC-DC regulator IC, the max efficiency of the chip
is up to 92%.
3.2. The output current is very large, the continuous output current is up to 5 Amps, and the
burst output current is up to 7.5 Amps.
3.3. Output short-circuits protection function.
3.4. A metal shield covers almost all the electronic components, and a filter (ferrite ring) is
attached with the output wires to significantly reduce the electromagnetic interference.
3.5. Ultra-wide input voltage from 8V-42V.
3.6. Safe power on with the polarity protection function. If the input polarity is not correct, the
UBEC can’t work, but it will not be damaged. What you need to do is just swapping the
battery pack’s polarity.
3.7. Shows the working status with an indicator (LED), it lights when the output is in normal
range.
3.8. A switch to turn on or turn off the output.
3.9. Accessory: A step-down voltage regulator with 0.7V down (from 6.0V to 5.3V)
4. Wiring
5. About RF interference
Although we have tried our best to reduce the electromagnetic interference caused by switch model
UBEC, it may still cause some interference to the receiver. So please install the filter (ferrite ring) far
away from the UBEC’s main board, and DON’T stack the filter on the main board. Please put the
whole UBEC as far as possible away from the receiver.
6. How to Use the UBEC?
6.1. Change the output voltage
The output voltage is chosen by a jumper. Please look at the upper picture, there are 3 pins at the
right corner, the upper one is Pin1, the middle one is Pin2, and the bottom one is Pin3. If the switch
is located at Pin1 and Pin2, the output is 6V. If the switch is located at Pin2 and Pin3, the output is
5V.
6.2. Working status indicator (LED)
The LED shows the status of the UBEC. When it lights, it means the UBEC has the normal output. If
it couldn’t light, please check the battery connections.
6.3. Turn on or turn off the UBEC
Push the switch to the "ON" position to turn on the UBEC; Push the switch to the “OFF" position to
turn off the UBEC.
6.4. About the 0.7V step-down voltage regulator
This 0.7V regulator is used for servos cannot work with 6V (including Futaba servo 9241, 9251,
9253, 9254, 9255, 9256 and etc). It changes the voltage from 6V to 5.3V. When the UBEC output is
set to 6V, please connect the regulator between the receiver and the above servos.
If you are using a servo can work with 6V input, the 0.7V regulator is unnecessary.
5A UBEC
5A UBEC
5A UBEC
5A UBEC5A UBEC Switch
Input
Output
6V
5V Jumper for output
voltage selection

Produktspezifikationen

Marke: Hobbywing
Kategorie: Funkgesteuertes Spielzeug
Modell: UBEC 5A HV (3-10S)

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hobbywing UBEC 5A HV (3-10S) benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Funkgesteuertes Spielzeug Hobbywing

Hobbywing

Hobbywing XeRun XR10 Pro WP Bedienungsanleitung

25 September 2024
Hobbywing

Hobbywing XeRun XR10 Stock Spec G2 Bedienungsanleitung

25 September 2024
Hobbywing

Hobbywing XeRun XR10 Justock G3S Bedienungsanleitung

25 September 2024
Hobbywing

Hobbywing XeRun XR8 PRO G3 Bedienungsanleitung

25 September 2024
Hobbywing

Hobbywing XeRun XR10 Justock G3 Handout Bedienungsanleitung

25 September 2024
Hobbywing

Hobbywing XeRun XR8 Plus G2S Bedienungsanleitung

25 September 2024
Hobbywing

Hobbywing XeRun XR10 Pro 1S Heavy Duty Bedienungsanleitung

25 September 2024
Hobbywing

Hobbywing XeRun XR10 Stock Spec 1S Bedienungsanleitung

25 September 2024
Hobbywing

Hobbywing XeRun XR10 PRO 160A Bedienungsanleitung

25 September 2024
Hobbywing

Hobbywing Xerun V10 G3 Bedienungsanleitung

5 September 2024

Bedienungsanleitung Funkgesteuertes Spielzeug

Neueste Bedienungsanleitung für -Kategorien-

Proline

Proline Trencher Bedienungsanleitung

4 Oktober 2024
Futaba

Futaba 12Z Bedienungsanleitung

4 Oktober 2024
Graupner

Graupner 33718.XT60 Bedienungsanleitung

3 Oktober 2024
Amewi

Amewi Hyper Go Bedienungsanleitung

1 Oktober 2024
Carson

Carson Drift Burner Bedienungsanleitung

1 Oktober 2024
Carson

Carson Micro X-Warrior 2.0 Bedienungsanleitung

1 Oktober 2024
Biltema

Biltema 45-8119 Bedienungsanleitung

1 Oktober 2024
Traxxas

Traxxas Stampede Bedienungsanleitung

29 September 2024
Spektrum

Spektrum DX2E 2Ch DSMR Surface Radio w/SR310 Bedienungsanleitung

23 September 2024
Futaba

Futaba SKYSPORT_4YBF Bedienungsanleitung

17 September 2024