Havis C-3090-4 Bedienungsanleitung

Havis Kfz-Bausatz C-3090-4

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Havis C-3090-4 (4 Seiten) in der Kategorie Kfz-Bausatz. Dieser Bedienungsanleitung war für 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
INSTALLATION INSTRUCTIONS C- - 3090’s & C 3089’s
COMPUTER LAPTOP MOUNT AND ACCESSORIES
TOOLS NEEDED:
Ratcheting wrench
Standard socket set
Open-end wrench set
Allen wrench set
Screwdriver set
Always!
Read all instructions before installing any Havis, Inc. products.
Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
Use hardware provided with install kit
1. MOUNTING C-3090-3 or 4 & C-3089-3 or 4 to C- TCB’S
Photo #3 on page #2 is a basic assembly
instruction of a C-3090-3 (w/ tilt/swivel)
mounting to a C-TCB-x.
The tilt/swivel assembly, ( , which Photo #1)
comes pre-assembled to the C-3090 from the
factory, will bolt directly to the rotating plate,
using the hardware loosely attached to the
plate. You do not need to unassembled the
tilt/swivel from the C-3090.
Note: Be sure the 2” fender washer is assembled between
the rotating plate and the tilt/swivel assembly.
2. C-3090-1 or 2 & C-3089-1 or 2 MOUNTING TO
VEHICLE TUNNEL PLATES:
The C-3090 will come pre-assembled with
tilt/swivel attached.
Mount trak kit into vehicle.
Place console and C-3090 into desired
position on trak. (Photo #2)
Note: Be sure assembly does not interfere with dash or
console.
Slide ¼-20 hex nuts into slots on side of trak
in location to mount C-3090.
Attach C-3090 to trak using ¼-20 x ½” hex
bolts and washers. Tighten in desired area.
Photo #1
Photo #2
C-3090_INST_6-09.docx6- 09
3. ADJUST C-3090 PLATFORM FOR SPECIFIC LAPTOP:
The C-3090 will need to be adjusted to
properly hold your particular laptop.
Note: Do not adjust the latch on the underside of the
laptop.
Loosen the “L” clamps on the sides of
the C-3090. (Photo #4)
Release the latch on the underside of the
laptop.
Place laptop on top of C-3090 platform
and close the latch.
Open laptop and adjust “L” clamps so
they are firm against inside lip of
computer on the latch side.
Loosen ¼-20 nylock nuts on the plate on underside of laptop assembly and adjust to
width of laptop.
Photo #3
C-3090_INST_6-09.docx6- 09
Adjust “L” brackets to clamp the laptop firm.
Release latch and test for strength. Adjust if necessary.
4. PLATFORM WIDENING INSTRUCTIONS: ( Photo #5)
On larger laptops, it may be necessary to use a different hole pattern on the plate.
Remove (#1 in photo #5) ¼” nylock nuts and washers
Remove bracket and use alternate mounting holes to create a wider (#2 in photo #5)
platform.
5. OPTIONAL SCREEN SUPPORT (C-SS & C- -2): ( SS Photo #6)
With laptop adjusted for C-3090, open screen on computer.
With screen open, remove ¼-20 nylock nut from “L” tab holding laptop.
Loosely attach optional screen support as shown.
Adjust screen support around screen and tighten hardware.
Test screen movement.
Photo #4
#1
#2
Photo #5
Photo #6


Produktspezifikationen

Marke: Havis
Kategorie: Kfz-Bausatz
Modell: C-3090-4

Brauchst du Hilfe?

Wenn Sie Hilfe mit Havis C-3090-4 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Kfz-Bausatz Havis

Bedienungsanleitung Kfz-Bausatz

Neueste Bedienungsanleitung für -Kategorien-