Harley-Davidson J02994 (2003) Bedienungsanleitung
Harley-Davidson
Motorrad
J02994 (2003)
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Harley-Davidson J02994 (2003) (2 Seiten) in der Kategorie Motorrad. Dieser Bedienungsanleitung war fĂĽr 30 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
INSTRUCTIONS
-J02994 REV. 10-10-2003
SHIFTER LINKAGE COVER
General
This “Harley-Davidson script”-style shifter-linkage cover kit
fits 1997 and later FXDWG (Dyna Wide Glide®) model motor-
cycles. This kit also fits 1993 and later Dyna models
equipped with Forward Control Kit 49080-03.
NOTE
A Service Manual for your model motorcycle is available
from any Harley-Davidson dealer.
Installation
1. See the Service Parts illustration. Obtain an upper mount-
ing bracket (2), lower mounting bracket (3), two 1/2-inch
long screws and the Allen wrench (6) from the kit.
2. See Figure 1. Assemble the upper and lower mounting
brackets onto the shaft of the ball screw shell at one
end of between the ball screw (3) andthe shifter rod (1),
the jam nut (2) so the shaft passes above the three
holes in the brackets.
Insert the two screws in the outboard holes of the lower
bracket, and use the Allen wrench to thread them part
way into the holes in the upper bracket. Do not fully
tighten the screws at this time.
3. Repeat Steps 1 and 2 at the other end of the shifter rod.
4. Position the linkage cover (1) on top of the linkage and
examine the fit.
• If the cover fits properly, proceed to Step 8.
• If the center holes in the front and rear upper mounting
brackets cannot be adjusted to line up with the holes
on the inboard side of the cover, the linkage will need
to be adjusted to accept the cover. Proceed to Step 5.
5. See Figure 1 (below) and SHIFTER LINKAGE
ADJUSTMENT in the Service Manual. To adjust the
length of the linkage, remove the link attaching nut (5)
and flat washer at the forward ball screw.
6. Loosen the jam nut (2) at the front end of the shifter rod,
and remove the mounting bracket installed in Step 3.
Rotate the forward ball screw shell to achieve the prop-
er length to allow mounting of the cover.
7. Re-attach the ball screw to the shifter lever with the flat
washer and nut removed in Step 5. Torque the nut on
the ball stud to 70-90 in-lbs (7.9-10.2 Nm).
Torque the jam nut on the shifter rod to 20-24 ft-lbs
(27.1-32.5 Nm).
8. Fasten the rear of the cover (1) to the rear upper bracket
using a short screw (5) from the kit. Fasten the front of
the cover to the front bracket with the remaining screw.
Tighten the cover securely to the upper brackets.
Position the cover upright over the shifter rod, and tight-
en the four remaining screws to clamp the brackets
securely to the ball screw shells.
9. If the linkage needed adjustment (Steps 5 through 7),
the position of the shift foot lever (6) may have
changed.
To return the lever to the original position, loosen the
socket head screw (7) holding the lever to the shaft. Pull
the lever from the shaft, rotate to the desired angle and
slide the lever back onto the shaft.
Torque the screw to 18-22 ft-lbs (24.4-29.8 Nm).
®
Kit Number 33878-04
1 of 2
Figure 1. Stock Shifter Linkage
i02475
1. Shifter rod
2. Jam nut (2)
3. Ball screw shell (2)
4. Shifter lever
5. Link attaching nut
6. Shift foot lever
7. Socket screw
2
31
4
5
2
6
3
7
-J02994 2 of 2
Service Parts
®
Shifter Linkage Cover
Date 10/03
Part No. 33878-04
Item Description (Quantity) Part No.
1 Linkage cover Not sold separately
2 Mounting bracket (upper) (2) 33879-04
3 Mounting bracket (lower) (2) 33880-04
4 Screw, button head, hex socket,
#10-24 x 1/2 in (4) 94381-92T
5 Screw, button head, hex socket,
#10-24 x 1/4 in (2) 3339
6 Allen wrench, 1/8 in Not sold separately
i02476
1
5
2
3
4
5
2
3
4
6
Produktspezifikationen
| Marke: | Harley-Davidson |
| Kategorie: | Motorrad |
| Modell: | J02994 (2003) |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Harley-Davidson J02994 (2003) benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Motorrad Harley-Davidson
20 April 2024
26 Februar 2024
13 November 2022
18 Oktober 2022
16 Oktober 2022
Bedienungsanleitung Motorrad
- Motorrad Juki
- Motorrad Yamaha
- Motorrad Mitsubishi
- Motorrad Beta
- Motorrad Husqvarna
- Motorrad BMW
- Motorrad Honda
- Motorrad Aprilia
- Motorrad Ducati
- Motorrad KTM
- Motorrad Suzuki
- Motorrad Danfoss
- Motorrad Triumph
- Motorrad GasGas
- Motorrad Hero
- Motorrad Kawasaki
- Motorrad Cagiva
- Motorrad ELAC
- Motorrad Texas
- Motorrad Bajaj
- Motorrad Piaggio
- Motorrad Victory
- Motorrad Zero
- Motorrad Hyosung
- Motorrad Sherco
- Motorrad Indian
- Motorrad Mash
- Motorrad Royal Enfield
- Motorrad CRRCpro
Neueste Bedienungsanleitung fĂĽr -Kategorien-
11 August 2024
6 August 2024
4 August 2024
19 Juni 2024
18 Juni 2024
18 Juni 2024
8 Juni 2024
8 Juni 2024
8 Juni 2024
8 Juni 2024