Gre RKFA100 Bedienungsanleitung

Gre Staubsauger RKFA100

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Gre RKFA100 (44 Seiten) in der Kategorie Staubsauger. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/44

BK0017000 / PA -

Robot Zwembadreiniger

Bedieningsinstructies

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL THE INSTRUCTIONS

CAUTION: Do not plug the power supply into a grounded outlet or do not switch the

pool cleaner “ON” if it is not fully immersed in water. Operating the cleaner out of water

will cause severe damage immediately and will result in loss of warranty.

Allow the cleaner to remain in the pool for 15 to 20 minutes following the end of its

cleaning cycle. This will allow the motors to cool adequately. Do not leave the cleaner

in the pool all the time. Always remember to turn the power supply “OFF” and unplug it

from the power outlet before removing the cleaner from the pool.

WARNING: The cleaner must not be used when people are in the water. For use

with swimming pool only

Safety Note

- The unit must be supplied through a residual current device (RCD) having a rated

residual operating current not exceeding 30 mA

- The connection to the branch circuit should be consistent with the local and national

wiring rules (electrical code).

- Mishandling of the unit can result in leakage of lubricants.

- If the supply cord is damaged, it must be replaced by the manufacturer’s service

agent or a qualified and trained person in order to avoid hazards.

Dear Customer,

Thank you for choosing our product to clean your pool. We hope that you will enjoy

using your new robot to maintain your swimming pool for years to come.

Before you begin to use your robot, please take a few minutes to carefully read these

operating instructions.

Again, thank you for choosing our product.

ENGLISH

Components

Your new automatic pool cleaner contains:

- The robotic pool cleaner with its floating cable.

- The Power Supply (transformer).

- Cart (optional)

Please read this manual completely before operating your pool cleaner.

While the appearance of your cleaner and some of its components may differ from those

shown here, the function of the cleaner, operating procedures and maintenance

practices are the same.

WARNING: A Ground Fault Current Interrupter (GFCI-USA) or a Residual Current

Device (RCD-EUROPE) must be installed to protect your electric outlet and prevent

any possible electric shock.

This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

their safety. Children should be supervised to ensure that they do not

play with the appliance.

SAVE THESE INSTRUCTIONS

1) Handle

2) Outlet Top

3) Filter Lock Release

4) Filter Top Access

5) Handle Lock Mechanism

1 1 2

6) Side Plate

7) Drive Track

8) Scrubbing Brush

9) Unit Body

12 cm

(4 inch)

3.6m/11.8ft

1. Place the power supply (transformer) at least 3.6 meters / 11.8 feet from the pool and at

least 12 cm / 4 Inch above the surface (fig.1). The transformer will supply low voltage to

the cleaner.

2. Uncoil the cable.(fig.1a)

3. ONLY FOR MODELS WITH FLOATING HANDLE - For proper operation, lock

the moveable handle diagonally across the top of the cleaner's body. Push down

on the handle lock mechanism and slide the handle all the way to the end, then

release the lock. Depending on your model, the handle might be lock button

vertical or horizontal (fig.2a, 2b). The handle will remain fixed in this position.

Repeat this process on the other side of the cleaner.

Remember, the handle must be fixed diagonally (fig.2c)

unit

2c2a Handle lock vertical Handle lock horizontal

Operating the pool cleaner

4. Place the unit in the water. Turn the unit

side to side in the water to allow air to

escape from the body and then let the

cleaner sink to the bottom of the pool

(fig.3). Then, spread the cable over the

surface of the pool as evenly as possible

(fig.1).

5. Plug the cable into the power supply. Make sure the key on the plug exactly

corresponds with the key slot on the socket of the power supply (fig.4).

Plug the power supply into a grounded outlet. Ensure that the electric outlet has been

properly grounded (fig.5). Press the “ON” button on the power supply. The light will

glow indicating that the system is “ ON “ and the pool cleaner will start the cleaning

cycle. The unit keeps record of the number of cleaning cycles. Only an authorized

service center can display the accumulated cleaning cycles.

WARNING: A Ground Fault Current Interrupter (GFCI-USA) or a Residual Current

Device (RCD-EUROPE) must be installed to protect your electric outlet and prevent

any possible electric shock.

Produktspezifikationen

Marke:	Gre
Kategorie:	Staubsauger
Modell:	RKFA100
Gewicht:	16500 g
Produkttyp:	Roboter-Pool-Reiniger
Produktfarbe:	Blue,White
Verpackungsbreite:	510 mm
Verpackungstiefe:	520 mm
Verpackungshöhe:	450 mm
Automatische Abschaltung:	Ja
Kabellänge:	18 m
Einfach zu bedienen:	Ja
Betriebsanleitung:	Ja
Verpackungsart:	Box
Filtertyp:	Filterbeutel
Produkte pro Palette:	12 Stück(e)
Geeignet für:	Pool
Verpackungsvolumen:	11.93 cm³
Mindestbestellmenge:	1 Stück(e)
Filterkapazität:	16000 l/h
Intrastat-Code:	84798997
Geeignet für die Reinigung:	Boden
Geeignet für Pools bis zu:	100 m²
Eingebauter Filter:	Ja
Filterbeutel:	Ja