Gemini 7201 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Gemini 7201 (9 Seiten) in der Kategorie Autoalarm. Dieser Bedienungsanleitung war für 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/9
7201
by GEMINI TRADING S.r.l. Via Luigi Galvani 12 21020 Bodio Lomnago (VA) Italia
Tel. +39 0332 943211 - Fax +39 0332 948080
E-mail : info@gemini-alarm.com
7208
0682
DESCRIPTION
The system Gemini 7201 is a compact alarm supplied with sensors and siren, which can be
installed on vehicles with 12Volt battery-negative to earth.
FUNCTIONS
GEMINI 7201.
- Compact alarm with dynamic code (Frequency 433.92 MHz).
- Blinker and electronic siren.
- Negative control for supplementary siren.
- Electrical central door locking control (negative or positive) windows and electric sunroof (for
vehicles equipped with Pack-comfort system).
- Perimetric and volumetric protection (US and HF models).
- LED’s memory and wiring connections diagnosis.
- Remote controlled PANIC function.
He alarm systems are equipped with 2 codified transmitters (art. 7208E).
INSTALLATION INSTRUCTIONS (for the installer)
- To make universal the central door locking system it is necessary to use a 5056 module.
- Connect the power feed wire to the battery positive terminal and the earth directly to the
vehicle frame.
- Connect the alarm Green-Brown wire to the door pin-switch.
- Avoid routing connection wires next to interference sources (sparking plugs cables, high
voltage coil).
- The alarm must be installed in the engine compartment protected from water and with the
key lock switch turned to the top.
- If you install an ultrasonic module the ultrasonic heads must be positioned at the top of each
windscreen pillar and must be pointing at each opposite diagonal corner away from the facia
outlets.
DIP-SWITCHES PROGRAMMING TABLE
1 ON Current absorption sensor ON
1 OFF Current absorption sensor OFF
2 ON Closure control 6 seconds
2 OFF Closure control 1 second
3 ON Comfort control ON (25 seconds)
3 OFF Comfort control OFF
4 ON Diagnostics ON
4 OFF Diagnostics OFF (normal use)
5 ON
5 OFF
Do not use
6 ON Self-learning of a new active code
6 OFF Self-learning of a new excluded code (normal use)
ATTENTION : SET THE DIP-SWITCHES BEFORE TURNING THE EMERGENCY KEY TO ON.
FOLLOWING THE PRESENT RULES IT IS ADVISABLE TO SET THE DIP-SWITCH N. 1 TO OFF.
DIAGNOSTICS: (final check-up o f the installer or quick after sale checks).
The diagnostics function allows during the test or at the end of the installation to verify quickly the
correct working of the alarm system and the electrical connections of the vehicle plant.
DIAGNOSTICS INLET. With the emergency key to OFF, set the dip-switch N.4 to ON. The activation
of the diagnostics function is signalled by 4 acoustic/optical signalling while supplying the alarm
system. At the end of the signalling the module outlets (+A) and the engine immobilisation
activates; the LED lights fix.
In this condition it is possible to test each inlet and if the external connections and/or the internal
circuits of the device work correctly one audible tone or one-direction indicator lights flashing signal
each alarm triggering.
It is necessary to wait 1 second between each alarm input triggering. In the diagnostics modality
the transmitter 1 button does not work as arming/disarming button but it is used to verify the
transmitter’s working. An audible tone or one direction indicator lights flashing signals the correct
working.
The transmitter 2 button activates the Panic alarm. This modality allows testing the siren working
and the outlet of the additional siren with negative control.
To stop the Panic alarm it is necessary to press again on the button 2 of the transmitter (followed
by a neutral period of 5 seconds).
DIAGNOSTICS OUTLET.
1. Press on the transmitter 2 button to activate the panic function.
2. During the alarm signalling, pressing on the transmitter 1 button the system goes back to the
normal working.
ATTENTION! AT THE DIAGNOSTIC OUTLET SET THE DIP-SWITCH N.4 TO OFF.
WIRING CONNECTIONS
(disconnect the negative pole of the battery and only reconnect after the installation is complete)
FUNCTION WIRE COLOUR
Earth ðð BLACK initialled “M”
Battery positive ðð BLACK initialled “R”
Ignition live ðð YELLOW
Direction indicator lights ðð 2 x ORANGE
Door pin switch ðð GREEN-BROWN
Boot and bonnet switch ðð GREEN
Positive alarm armed ðð PINK
Sensors inlet ðð GREEN-BLACK
Outlet negative control for
additional siren ðð YELLOW-BLACK
Central door locking ðð YELLOW-RED, YELLOW-GREY, RED-GREY
NOTE: in the wiring harness there are 2 connectors; connect the 4-pin connector to the
ultrasonic module and the 2-pin connector to the LED.
WORKING DESCRIPTION
ALARM ARMING
Press on the transmitter 1 button. The arming is signalled by 1 direction indicator lights flashing
and one acoustic signal (can be excluded).
ALARM DISARMING
Press on the transmitter 1 button. The disarming is signalled by 3 direction indicator lights flashing
and 3 acoustic signalling (can be excluded); 5 direction indicator lights flashing and 5 audible tones
(can be excluded) if an alarm condition has occurred.
SPECIAL FUNCTIONS
Panic
Is obtained pressing the transmitter 2 button with the alarm armed or disarmed after the neutral
time of 45 seconds. The siren activates for 29 seconds. To de-activate the siren within the 29
seconds, press again on the transmitter 2 button.
SIREN EXCLUSION
While alarm disarmed, turn the ignition key of the vehicle to ON. Press on the transmitter 2 button
for at least 3 seconds, the LED lights fix till the releasing of the transmitter’s button to signal the
siren sound exclusion.
Turn again the ignition key to OFF and arm the alarm system. The disarming of the system sets to
zero the function.
SELF-LEARNING OF THE CODE OF A NEW TRANSMITTER.
1. Disarm the alarm with the transmitter.
2. Set the dip-switch N.6 to ON.
3. Turn the vehicle ignition key to ON for at least 1 second and then to OFF. The LED lights fix till
the ignition key is turned to OFF.
4. Turn the key to OFF and within 30 seconds press one of the transmitter’s buttons to learn. The
LED lights for 0,5 seconds to signal the code memorisation.
NOTE: If the operation is not carried out within 30 seconds it will be necessary to repeat the
operation from point 3.
It is possible to learn a maximum number of 4 transmitters; for each transmitter’s coding repeat the
operation from point 3.
ATTENTION! AT THE END OF THE PROCEDURE SET THE DIP-SWITCH N.6 TO OFF.
ULTRASONIC SENSOR EXCLUSION AND WINDOWS CLOSURE.
During the first 25 seconds of neutral time, it is possible to de-activate the ultrasonic sensors and to
stop the window closure pressing on the transmitter 2 button. One-direction indicator lights
flashing signals the operation.
If the time set is 1,5 or 6 seconds, the exclusion of the ultrasonic inlet disables the positive outlet on
the alarm Pink wire (+A); to obtain the disabling of the closure relay set the comfort time of 25
seconds.
To exclude the ultrasonic inlet with the windows completely closed; it is necessary to wait the
complete closure of the window and to press on the transmitter 2 button.
ACOUSTIC SIGNAL LING EXCLUSION (CHIRP)
1. While alarm disarmed, turn the ignition key of the vehicle to ON.
2. Press on the transmitter 1 button for at least 3 seconds. The LED flashes for 0,5 seconds to
signal the audible tone exclusion.
3. Position again the vehicle ignition key to OFF.
CHIRP FUNCTION ACTIVATION.
1. While alarm disarmed turn the vehicle ignition key to ON.
2. Press on the transmitter 1 button for at least 3 seconds. The LED flashes for 0,5 second; the
activation of the Chirp function is signalled by one audible tone.
LED’S MEMORY
While alarm disarmed it is possible to verify if an alarm condition has occurred and to determine
the cause following the LED flashing.
LED SIGNALLING ALARM TRIGGERING
Y l Y Ultrasonic sensors inlet
Y Y l Y Y Ignition live (engine immobilisation)
Y Y Y l Y Y Y Door, boot and bonnet pin switch and
absorption sensor.
l LED OFF (2,5 seconds) Y LED ON ( 400mS)
NOTE: to stop the LED flashing it is necessary to turn the ignition key to ON.
ACTIVE FUNCTIONS WHILE ALARM ARMED
IMMEDIATE AFTER 45 SECONDS
- Ignition live: activates while arming the
system; the detection is obtained after the
neutral time of 45 seconds.
- cut wires (art.7203)
- current absorption;
- door, boot and bonnet opening;
- sensors inlet.
NOTE: the neutral time is signalled through the LED lightning fix.
Transmitters battery discharging
The discharging of the battery is signalled through the
LED of the transmitter. If the LED flashes while
pressing one of the transmitter’s buttons it is
necessary to replace the batteries.
Batteries model : CR1616
Note:
put the batteries in the appropriate container.
TECHNICAL DATA
Power supply 12VDC
Current absorption alarm ON with US module 16mA
Current absorption alarm OFF 9 mA
Working temperature -30°+ 85°C
Engine immobilisation relay contact capacity 8A a 20°C
Blinker and central door locking relay contact capacity 10A a 20°C
Power sound at 1 meter in open space > 118dB
Minimum sensitivity absorption sensor 5W
Current for positive control alarm armed 500 mA
Produktspezifikationen
| Marke: | Gemini |
| Kategorie: | Autoalarm |
| Modell: | 7201 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Gemini 7201 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Autoalarm Gemini
16 September 2024
14 August 2024
13 August 2024
13 August 2024
13 August 2024
12 August 2024
12 August 2024
12 August 2024
11 August 2024
11 August 2024
Bedienungsanleitung Autoalarm
- Autoalarm Technaxx
- Autoalarm Waeco
- Autoalarm Audiovox
- Autoalarm Cobra
- Autoalarm Viper
- Autoalarm GT
- Autoalarm Jablotron
- Autoalarm Spy
- Autoalarm Clifford
Neueste Bedienungsanleitung für -Kategorien-
30 August 2024
23 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024