Garmin GA 38 GPS Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Garmin GA 38 GPS (38 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/38
Remote GPS Antenna Installation Instructions.................................................................................. 2
Instructions d'installation de l'antenne GPS externe.......................................................................... 5
Istruzioni di installazione dell'antenna GPS esterna.......................................................................... 8
Externe GPS-Antenne – Installationsanweisungen......................................................................... 11
Instrucciones de instalación de la antena GPS remota................................................................... 14
Instruções de Instalação da Antena de GPS Remota..................................................................... 17
Installatie-instructies voor externe GPS-antenne.............................................................................20
Vejledning til installation af GPS-fjernantenne................................................................................. 23
GPS-etäantennin asennusohjeet..................................................................................................... 26
Installeringsinstruksjoner for ekstern GPS-antenne.........................................................................28
Installationsinstruktioner för fjärrmonterad GPS-antenn.................................................................. 31
Instrukcja instalacji zdalnej anteny GPS.......................................................................................... 34
远程 GPS 天线安装说明...................................................................................................................37
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used without the express permission of Garmin.
El número de registro COFETEL/IFETEL puede ser revisado en el manual a través de la siguiente página de internet.
March 2016 190-01139-91_0BPrinted in Taiwan
TA-2013/783
Remote GPS Antenna Installation
Instructions
WARNING
See the Important Safety and Product Information guide in the
GPS device product box for product warnings and other
important information.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
This antenna can be installed to provide a stronger GPS signal
to a compatible Garmin® chartplotter. This antenna uses a BNC
connector to connect to the port labeled ANTENNA or EXT GPS
on a compatible Garmin chartplotter.
Antenna Mounting Considerations
You can mount the antenna on a flat surface, install it under
fiberglass, or attach it to a standard 1 in. OD, 14 threads per
inch, pipe-threaded pole (not included). You can route the cable
outside of the pole or through the pole. For optimal performance,
consider these guidelines when selecting the antenna mounting
location.
To avoid interference with a magnetic compass, the antenna
should not be mounted closer to a compass than the
compass-safe distance value listed in the product
specifications.
To ensure the best reception, the antenna should be
mounted in a location that has a clear, unobstructed view of
the sky in all directions À.
The antenna should not be mounted where it is shaded by
the superstructure of the boat
Á, a radome antenna, or the
mast.
The antenna should not be mounted near the engine or other
sources of Electromagnetic Interference (EMI) Â.
If a radar is present, the antenna should be mounted above
the path of the radar Ã. If necessary, the antenna may be
mounted below the path of the radar
Ä.
The antenna should not be mounted directly in the path of the
radar Å.
The antenna should be mounted at least 3 ft. (1 m) away
from (preferably above) the path of a radar beam or a VHF
radio antenna Æ.
On a sailboat, to prevent inaccurate speed readings caused
by excessive heeling, the antenna should not be mounted
high on the mast.
The antenna provides more-stable readings when located
nearer to water level.
Testing the Mounting Location
1Temporarily secure the antenna in the preferred mounting
location and test it for correct operation.
2If you experience interference with other electronics, move
the antenna to a different location, and test it again.
3Repeat steps 1–2 until you observe full or acceptable signal
strength.
4Permanently mount the antenna.
Surface Mounting the Antenna
NOTICE
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid any cracking in the gel-coat layer when the screws are
tightened.
Stainless-steel screws may bind when screwed into fiberglass
and overtightened. Garmin recommends applying an anti-seize
lubricant to the screws before installing them.
Before you permanently mount the antenna, you must test the
mounting location for correct operation (Testing the Mounting
Location, page 2).
1Using the surface-mount bracket À as your mounting
template, mark the three pilot-hole locations and trace the
cable-hole in the center of the bracket.
2Set the surface-mount bracket aside.
Do not drill through the bracket.
3Drill the three 3.2 mm (1/8 in.) pilot holes.
4Use a 25 mm (1 in.) hole saw to cut the cable hole in the
center.
2 Installation Instructions
5Place the seal pad Á on the bottom of the surface-mount
bracket, aligning the screw holes.
6Use the included M4 screws to secure the surface-mount
bracket to the mounting surface.
7Route the cable  through the 25 mm (1 in.) hole and
connect it to the antenna.
8Verify the large gasket à is in place on the bottom of the
antenna, place the antenna on the surface-mount bracket,
and twist it clockwise to lock it in place.
9Secure the antenna to the mounting bracket with the included
M3 set screw Ä.
10 Route the cable away from sources of electronic interference.
Mounting the Antenna with the Cable Routed Outside
the Pole
Before you permanently mount the antenna, you must test the
mounting location for correct operation (Testing the Mounting
Location, page 2).
1Route the cable through the pole-mount adapter
À, and
place the cable in the vertical slot Á along the base of the
pole-mount adapter.
2Screw the pole-mount adapter onto a standard 1 in. OD, 14
threads per inch, pipe-threaded pole (not included).
Do not overtighten the adapter on the pole.
3Connect the cable to the antenna.
4Place the antenna on the pole-mount adapter and twist it
clockwise to lock it in place.
5Secure the antenna to the adapter with the included M3 set
screw Â.
6With the antenna installed on the pole mount, fill the
remaining gap in the vertical cable slot with a marine sealant
(optional).
7Attach the pole to the boat if it is not already attached.
8Route the cable away from sources of electronic interference.
Mounting the Antenna with the Cable Routed Through
the Pole
Before you permanently mount the antenna, you must test the
mounting location for correct operation (Testing the Mounting
Location, page 2).
1Position a standard 1 in. OD, 14 threads per inch, pipe-
threaded pole (not included) in the selected location, and
mark the approximate center of the pole.
2Drill a hole using a 19 mm (3/4 in.) drill bit for the cable to
pass through.
3Fasten the pole to the boat.
4Thread the pole-mount adapter onto the pole.
Do not overtighten the adapter.
5Route the cable through the pole and connect it to the
antenna.
6Place the antenna on the pole-mount adapter and twist it
clockwise to lock it in place.
7Secure the antenna to the adapter with the included M3 set
screw À.
8With the antenna installed on the pole mount, fill the vertical
cable slot Á with a marine sealant (optional).
9Route the cable away from sources of electronic interference.
Mounting the Antenna Under the Deck
NOTICE
Before attaching the under-deck mounting bracket to the
surface, verify the included screws will not penetrate the
surface. If the included screws are too long, you must purchase
surface-appropriate screws to complete the installation.
Before you permanently mount the antenna, you must test the
mounting location for correct operation (Testing the Mounting
Location, page 2).
Because the antenna cannot acquire signals through metal, it
must be mounted under a fiberglass surface only.
1Place the adhesive pads
À on the under-deck mounting
bracket Á.
2Place the antenna in the under-deck mounting bracket.
3Adhere the under-deck mounting bracket to the mounting
surface.
4Secure the under-deck mounting bracket to the mounting
surface with screws.
5Connect the cable to the antenna
Â.
6Route the cable away from sources of electronic interference.
Installation Instructions 3


Produktspezifikationen

Marke: Garmin
Kategorie: Nicht kategorisiert
Modell: GA 38 GPS

Brauchst du Hilfe?

Wenn Sie Hilfe mit Garmin GA 38 GPS benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Garmin

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-