Ganz GWK1 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ganz GWK1 (9 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 35 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/9
INS_GWK1_QS_REV– 07/7/15 PAGE 1
QUICK START GUIDE
INDUSTRIAL OUTDOOR 802.11A/N WIRELESS ETHERNET
Thank you for purchasing the GWave wireless kit . This quick start guide is from GANZ
designed to walk you through installation.
This guide applies to the following models:
GWK1: Industrial Point to Point Kit, FCC Version (Includes GWK1_AP and GWK1_CL)
An easy to read LED array displays unit operational status along with received signal
strength ensuring optimal installation and operation. See Figure 2 on Page 2 for LED
Indicator explanations.
See through Figures 3 5 beginning on Page 3 for mounting instructions.
This manual serves the following
GANZ Model Numbers:
GWK1
INS_GWK1_QS_REV– 07/7/15 PAGE 2
FIGURE 1 – INDUSTRIAL WIRELESS ETHERNET LINK
QUICK START USER GUIDE GWK1
FIGURE 2 – STATUS INDICATING LEDS
WEAK SIGNAL EXCELLENT SIGNAL
LED INDICATIONVISUAL CUE
POWER SOLID GREEN Power is supplied to the unit
OFF No power is supplied to the unit, or the unit is in reset.
LAN SOLID GREEN LAN Connected
OFF No Connectivity
RSSI1 SOLID RED Weak Connection
RSSI2 SOLID ORANGE Moderate Connection
RSSI3 SOLID GREEN Solid Connection
RSSI4 SOLID GREEN Excellent Connection
(Advisable to check Status Page to confirm RSSI is > -55)
SIGNAL STRENGTH:
RSSI1POWER
RSSI2LAN
RSSI3
RSSI4
BACKFRONT
BOTTOM
PORT 1PORT 2
IMPORTANT: Only plug PoE power to Port 1.
Connecting a PoE power source to the PSE Port (#2) will
cause a major device malfunction and void the warranty.
PORT 1 PORT 2
INS_GWK1_QS_REV– 07/7/15 PAGE 3
FIGURE 3 – INSTALLATION INSTRUCTIONS
QUICK START USER GUIDE GWK1
Step 1.
Unpack the mounting hardware from the box. Determine if this will be a pole or wall mount application.
The included Mounting kit is designed to support poles up to 2 in (5.8 cm) in diameter. If surface or wall-mounting, additional
hardware will be required.
Step 3.
Slide the weather proof assembly over the cable so it can be
screwed into the enclosure gland. Make sure the rubber sealing
ring is in place as shown in step 3A.
Tighten the weather proof assembly into the enclosure and also
tighten the cap that squeezes the rubber washer over the Ethernet
cable as shown.
Step 2.
A. Route the RJ45 connectorized Ethernet cable through the
weather tight gland connection as shown at left.
Note: The slit rubber washer allows a pre-terminated
Ethernet cable to be used.
Once the cable has been routed through the weather
connection as shown above, push the split rubber gasket
into place and loosely screw the cap that goes over the
rubber washer.
B. Snap the RJ-45 connector in place as shown
A
A
B
B C
Step 4.
A. Connect one end of an RJ-45 Ethernet cable to the OUT
port of the Power Injection Module (PIM) and the other end
to LAN of the access point.
Maximum length of the RJ-45 CAT5 cable is 100 meters.*
B. Connect the RJ-45 Ethernet cable attached to the PIM to a
network device, such as to a switch or to the PC you will use
to configure the access point.
C. Connect the power adaptor to the main electrical supply
and the power plug into the socket of the PIM.
PoE power input: Passive PoE (range 36 to 48 VDC).
The GW1 can also be powered by a suitable IEEE 802.3af/at
PSE device such as a PoE switch or injector.
D. A Drip Loop is recommended as additional precaution
against moisture entering the Access Point housing.
* Up to 200mW radio. For higher power radio upgrade to higher rating
power adapter.
A
D
D
D
B
Ethernet
Network
C
Network
Edge Device
P1 P2


Produktspezifikationen

Marke: Ganz
Kategorie: Nicht kategorisiert
Modell: GWK1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ganz GWK1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Ganz

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-