Futaba P-FTM-TFH Bedienungsanleitung

Futaba ferngesteuertes Spielzeug P-FTM-TFH

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Futaba P-FTM-TFH (8 Seiten) in der Kategorie ferngesteuertes Spielzeug. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

INSTRUCTION MANUAL

Item-No. P-FTM-TFH

TM-24

FUTABA 2.4 GHz T-FHSS Module F-Series

2 Instruction Manual TM-24 Module

This transmitter module is developed to convert

existing Futaba transmitters to the 2.4 GHz

frequency band with previous 35/40 MHz trans-

mission frequencies. The following instruction

manual explains in detail the connection and

operation of the TM-24 Module with the Futaba

F-14 transmitter as an example. The connecti-

on can be done with almost all transmitters via

existing plug connections, but some transmitters

require simple soldering. The installation can also

be done by our Futaba service against payment.

Installation Of 2.4 GHz Antenna

Two of the switch holes on the front side of the

transmitter are required to mount the transmitter

antenna. The clear cover plate can remain, only

the holes have to be opened.

If the existing holes are already fully occupied

with switch / prop modules, the transmitter anten-

na socket can also be attached to the left or right

front of the transmitter. For this, two holes with

D = 6mm must be drilled. The illustrated drilling

template can be used for this purpose. (See

pictures, also for the status LED).

Drilling template for antenna mounting on the

front side of the transmitter

Connecting The Module To The Transmitter

For connection, the enclosed adapter cable with

PCB is used.

The 3-pin connector (servo plug) of the adapter

cable F-14 with additional board is connected

to the corresponding plug-in contact (module

connection) of the TM-24 module. Observe

polarity! The black connecting wire of the plug

cable must point inwards towards the module

board (minus). It is important to ensure that all

3 contacts are plugged in at all times. The white

connection wire must point to the outer edge of

the module (signal line).

FürdieBefestigungderSendeantenne

werdenzweiderSchalterlöcherander

15mm

Antennenkabel

rdieBefestigungderSendeantenne

rdenzweiderSchalterlöcherander

SAFETY INSTRUCTIONS

Please read carefully the safety

instructions within the manual of

your transmitter!

TM-24 T-FHSS Module

Antenna Wire

3www.ripmax.com

Connection To Transmitter

The signal connector for the TM-24 module is

connected to the Trainer socket (4-pin) of the

transmitter F-14 using the adapter cable-trainer

connector. The plug-in contact is reverse-polarity

protected, but do not forcefully press it. One pin

of the plug is not used.

LED Connector

The connector of the LED is connected to the

LED connector. It is not possible to reverse the

polarity, but it should be done with a little „sensiti-

auchfürdieStatusLED,s.u.).

BohrschablonefürAntennen- MontageseitlichvorneamSender

15mm

Antennenkabel

LED-Anschluss

Modulanschluss

Binding-Taster

Antennenclip

AUS EIN

Modul-Schalter

Akkustecker

Akku Buchse F-14

Trainer-Buchse F-14

Adpater-Platine

Adapter PCB

vity“ in order not to damage the plug.

The LED with bracket is installed either in an

existing hole on the switch mounting brackets or

as shown in the gure.

Antenna Clip

The antenna cable has a connection clip, the

counterpart is seated on the module board (see

photo). The clip must be positioned carefully and

centrally to the round edge of the clip onto the

counterpart (antenna socket) and then depres-

sed carefully until a noticeable snapping action

occurs.

ATTENTION! This is an important task for the

safe operation of the F-14, which can have a

signicant impact on the achievable range and

transmission safety, so perform this procedure

accurately and correctly.

Connecting To TX Battery

The adapter board allows Futaba TX batteries to

be connected to the „old“ plug system and the

PCB Connection

Trainer Socket F-14

Battery Socket F-14

Module

Connector Link Button

Antenna Clip

LED Connector

Battery Plug

Module Switch

ON OFF

Produktspezifikationen

Marke:	Futaba
Kategorie:	ferngesteuertes Spielzeug
Modell:	P-FTM-TFH
Breite:	54 mm
Tiefe:	34 mm
Gewicht:	12 g
Produkttyp:	Empfänger Fernsteuerung
Höhe:	9 mm
Zertifizierung:	CE
Nicht für Kinder von 0-3 Jahren:	Ja
Stromverbrauch:	30 mA
Betriebsspannung (min):	5 V