Franke TP-50 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Franke TP-50 (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
FOOD WASTE DISPOSER
FRANKE TURBO PLUS OWNERS GUIDE
Important - Read all instructions thoroughly
Please retain for future reference
1. Read all instructions before using the appliance.
2. To reduce the risk of injury, close supervision is necessary
when an appliance is used near children.
3. Do not put fingers or hands into a waste disposer while it
is functioning.
4. Turn the power switch to the off position before attempting
to clear a jam or remove an object from the disposer.
5. When attempting to loosen a jam in a waste disposer,
use a long wooden utensil e.g. spoon.
6. When attempting to remove objects from a disposer, use
long-handled tongs or pliers.
7. To reduce the risk of injury please note:
- this disposer is not for grinding hard materials, such as
glass and metal;
- this disposer must be connected to the electric supply by
means of either a power supply cord or insulated wires in a
flexible conduit;
- when installing the disposer, care must be taken to ensure
that the reset button of the overload protection device
remains readily accessible.
8. Additionally for continuous feed models:
- Care must be taken to ensure that the supply is
disconnected by switching off the electric supply or by
removing the plug from the socket-outlet before freeing a
jammed rotor.
- When not operating the disposer, leave the stopper in place
to reduce the risk of objects falling into the disposer.
- Do not operate disposer unless splash guard is in place.
9. For proper electrical earth instructions see the
ELECTRICAL CONNECTION details of this manual.
10. All installations should be carried out by a qualified electrician.
11. The symbol on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead, it shall be handed over to the applicable environmental
collection point for the recycling of electrical and electronic
equipment. For more detailed information about recycling of
this product, please contact your local authority, your
household waste disposal service or the shop where you
purchased the product.
IMPORTANT SAFETY INSTRUCTIONS
Instructions pertaining to risk of fire, electric shock or injury to persons.
Save these instructions.
WARNING - When using electrical appliances, basic precautions should always be
followed, including the following:
www.franke.co.uk
For overflow or dishwasher connections, complete the
following procedure. Alternatively go on to section 3.
1 Using a blunt instrument (steel punch or wooden dowel),
knock out entire plug (see 1A). Do not use a screwdriver or
sharp instrument. (When knockout plug falls into Disposer,
you may remove it or grind it up when the disposer is used.
This will not damage the disposer in any way, but may take
some time to grind over the course of several uses).
2 Connect dishwasher hose (see 1B) using a hose clamp.
Make sure all plumbing connections are tight and in accordance
with all plumbing codes and ordinances. Run water and check
for leaks.
1. OVERFLOW/APPLIANCE CONNECTIONS
KNOCK
OUT PLUG
2A
WOOD OR
METAL DOWEL
2B
RUBBER
H OSE
DISHWASHER
HOSE
*
AI GAR P
*Air gap may not be require d
for all ins allations. Check loca t l
plumbing codes .
DRAIN
D RISPOSE
1A
1B
WHEN YOU DO NOT WISH TO UTILISE THE AIR SWITCH
(e.g. if hard wiring the WDU to a standard electrical switch)
Follow the following procedure:
1 With the disposer mounted on the sink and the unit connected
to the mains, turn ON the wall mounted switch.
2 Connect the air switch tube to the nipple on the underside
of the unit.
3 If the disposer is OFF, depress air switch actuator to
turn the disposer ON.
4 With the disposer ON pull air switch hose from disposer
connection and discard air switch actuator and hose.
5 Turn the disposer OFF by turning off the switch, usually
controlled by a wall mounted switch.
6 Operation of disposer is now controlled in a typical manner
by the wall mounted switch.
FRANKE TURBO PLUS MODELS
TP-50
Continuous Feed
TP-75
Continuous Feed
TP-125
Continuous Feed
TP-125B
Batch Feed
136
356
193
270
295
218
381
136
330
253
416
136
330
253
491
136
A Disassemble the mounting assembly, as it has been shipped,
by turning the sink flange until the projections align with the
notches in the mount ring and allow you to pull the sink flange
up and out of the remaining mount assembly. Note the
sequence of these parts as they are stacked and refer to A
and B to identify each part. Unpack the 3 mount screws and
screw them half way through the mount ring (notice “THIS
SIDE UP” is imprinted on top of the mount ring). Next, stack
the rubber gasket on top of the protector ring and sit them on
top of the pointed ends of the mount screws.
B Keep these assembled parts together and set aside. Before
you connect the disposer to the mount assembly under the
sink, you may want to practice engaging the groove of the
cushion ring to the ridge at the bottom of the sink flange
(see A and read Sec. 5).
C Be sure your sink is clean. Pack the underside rim of the sink
flange with plumber’s putty (see C). Position the sink flange so
it is centered and readable as you look into your sink. Push the
sink flange firmly into the sink opening to make a good seal.
DO NOT move or rotate the sink flange once seated or the seal
may be broken.
D Take the remaining portion of the mount assembly, as it was
set aside and make sure that the rubber gasket is on top of the
protector ring. From under the sink, while holding the sink
flange firmly with one hand, line up the notches in the mount
ring with the projections of the sink flange. Slide the mount
assembly up onto the sink flange, past the projections and
give the mount assembly a 1/4 turn, so that it will hang by
itself (see D).
E Tighten the 3 mounting screws evenly with a screwdriver
(see E). DO NOT OVERTIGHTEN! Trim off excess putty.
2a. INSTALLATION OF 3-BOLT MOUNTING ASSEMBLY
For TP-50, TP-75 and TP-125 models. Read completely before starting
NB - Pay close attention to the order of mount assembly parts,
as they have been correctly assembled by the factory.
(See A and B.)
metsyS tnuoM tloB-3
PROTECTOR RING
SINK MOUNT RING
MOUNTING SCREWS (3)
SINK FLANGE
SINK FLANGE GASKET
3A
STOPPER*
SINK FLANGE**
SINK
HOPPER
ELBOW
GASKET
SCREWS
SERIAL #- RECORD ON
WARRANTY CARD
MOUNTING
SCREWS**
SCREW
CLAMP**
PROJECTIONS
RIDGE
RIDGE
DISCHARGE
ELBOW
ELBOW
FLANGE
DISHWASHER
DISCHARGE INLET
CUSHION RING**
RUBBER SINK
FLANGE GASKET**
PROTECTOR RING**
MOUNT RING**
PLUMBER’S
PUTTY
END BELL
(ELECTRICAL
CONNECTIONS)
* Batch Feed Stopper looks different than the stopper illustrated.
** Mount Assembly (see B) 2
MOUNTING
SCREWS
PROTECTOR
RING
RUBBER
GASKET
SINK
FLANGE
CUSHION RING
3B
SCREW
CLAMP
MOUNTING
RING
Mount Assembly
B
3E
3D
3C
C D E
A


Produktspezifikationen

Marke: Franke
Kategorie: Nicht kategorisiert
Modell: TP-50

Brauchst du Hilfe?

Wenn Sie Hilfe mit Franke TP-50 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Franke

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-