Foscam FN8108W-B4 Bedienungsanleitung

Foscam Nicht kategorisiert FN8108W-B4

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Foscam FN8108W-B4 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

123 4 5

7 98 10 11 12

Quick Setup Guide

Security Tips

V1.0

305503001007

NVR Rear Panel

Software Operation

Placement of Wireless

IP Camera

1. Log In

NVR Kit Contents

8-Channel NVR

1.5m (5 ft) Ethernet Cable 4 x Bullet IP Cameras

USB Mouse Mounting Screws

For detailed manuals, tools, etc., please visit foscam.com/downloads.

Wireless Connectivity

WiFi Connection

Router

Computer HD-OUT Cable

LAN

Ethernet Cable

LAN

HD-OUT

Monitor

VGA Cable

VGA

HD-OUT

Foscam

Do not install the wireless NVR in humid and dusty

environment.

Put the wireless NVR in drafty environment in case of

ventilation port being blocked.

Check the power supply to avoid damage because of voltage

mismatch.

Make sure the wireless NVR working within suitable

temperature and humidity environment.

Please install the wireless NVR horizontally, and avoid

vibration.

Short circuit may occur when dust become wet on circuit

board. Please clean the dust on circuit board, connectors, and

NVR case.

Explosion may happen because of improper replacement of

battery, do not replace it by yourself; If you need, make sure it

is the same type of battery. And do not open or repair it.

Please use suitable and professional hard disk to ensure

continues and stable recording.

Lightning protection is needed when device is connected to

communication cables. Ethernet cable which comes from

outside, connecting to the wireless NVR directly is forbidden.

Right placement Wrong placement

4 x Power Adapters for Cameras 1 x Power Adapter for NVR

Quick Setup Guide Warranty Card

2. Setup Wizard

The Setup Wizard can walk you through some important settings

on the NVR.

Camera Installation

Important Note:

When installing the cameras please ensure that the connection

ports at the end of the pig tail wiring are not exposed, as they

are not weather-resistant.

0~90°

0~360°

0~90°

0~360°

Place the cameras in your preferred locations and use the

included screws to mount them.

The shape of wireless NVR signal coverage is a ball, antenna is located in

the center. Signal is strong around antenna, and weak in the dent area of

the 2 antennas.

Based on the signal spreading ways, please make the wireless IP Camera

keeping parallel or tangent with wireless NVR, which ensure stable signal

transmission and better picture quality.

Powering Up

DC 12V/2A

Mouse

WiFi Connection

GND

Please make sure the voltage of power supply is matched

with wireless NVR, and ground connection work well in

socket. Connect the NVR and cameras as shown in the gures

above. Once the NVR is plugged in, press the power switch

located on the rear panel.

After the NVR starts up successfully, the Power LED indicators

will turn green, it means system runs smoothly.

DC 12V/1A DC 12V/1A DC 12V/1A DC 12V/1A

VGA

Monitor

VGA Cable

VGA

HD-OUT

VGA Output

USB

Antenna

Reset

Power Input

(DC12V / 2A)

Power Switch

Ethernet Port

GND

① Turn on the power switch on the rear panel.

After the NVR starts up successfully, the power LED and HDD

LED indicators will turn green. The startup page is displayed

on the screen.

② Change password .

For your security, please set a new password for your NVR

before Log In.

④ After modifying the password, you will be taken to the

Setup Wizard.

① Setting the time.

Uncheck the checkbox

② Format HDD. Click the button to set up the HDD. Format

Note that this will delete all les on the HDD.

HDD Full Setting Select Stop Record and Overwrite . .

③ P2P. If you want to know the UID of the device, please scan

the QR code. If you don’t want to use the Setup Wizard

next time, uncheck the Setup Wizard checkbox. Click the

Finish button to complete the setup wizard.

or Right-click uncheck →Main Menu →Conguration →

the checkbox. Click the button to Setup Wizard Finish

complete the setup wizard.

Uncheck the checkbox

The live view interface will show you the video feed of each IP

Camera.

3. NVR adds IP Camera method

Note: The NVR and IP Camera are already paired. If you need to

match more cameras, please refer to the following steps.

F19911W is supported in this kit, besides the battery camera the

other Foscam models can be added by LAN.

① Right-click on main interface, select Pair IP Camera.

② Click and press the pairing button of the camera tail cablePair

at the same time, until it prompts that the pairing is successful.

③ When nished code matching, The live view interface will

show you the video feed of each IP Camera.

1. Click Pair

4. Record and Playback

① → → → Scheduled Record: Right-click Main Menu Record

choose recording channel (Actually, the Wi-Fi NVR →Save

system have default set 24h scheduled recording).

③ Login page.

Enter the Username and Password, then click on the OK

button.

If you want to modify it to alarm recording, please use the left

mouse button to select the time (turned to green), if the other

channels operate in the same way, select .copy

press the

pairing button

Add F19911W:

Add Other Foscam Camera:

① Right-click on main interface, select Channel cong.

② Click and then click .Add IPC Search Add

③ Select the Camera to be added.

④ Click and enter the username and password for the Add

camera, then click on the .Save

⑤ When nished added, the live view interface will show you

the video feed of each IP Camera.

1. Click Add IPC

2. Click Search Add

4. Click Add

3. Select the camera

to be added

13 14 15 1716

19 20 21 22

23 24

Technical Support

If you have problems with your Foscam device, please contact

the reseller you purchased from, or you can e-mail the

headquarters technical support team: support@foscam.com

Your valuable comments and suggestions on improving

Foscam products are welcomed!

Foscam App

2. Run the APP, and then register for a Foscam

Foscam account.

CE Certificate statement Website:

https://www.foscam.com/company/ce-certificate.html

Exporter and Importer Information Opened to Public:

https://www.foscam.com/company/open-information.html

www.foscam.com

Due to product upgrades and other reasons, this guide may be slow to

update, resulting in slight inconsistencies with the ocial website

information. Please take the ocial website(www.foscam.com)

information as the current standard.

Upgrade

1. You can upgrade your NVR and cameras system with local

Software.

Note:

① The upgrade le must be placed under the root directory of

the U disk.

② Don't lose power for during upgrade.

4. Preview: click device in list to enter preview interface,

select a channel to view it’s picture, as follow shows:

1. You can also simply go to the App Store or Google Play and

search for the term " ". Download the APP to yourFoscam

Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd

Addr: Room 901-902,Building 1B, Shenzhen International Innovation

Valley, Xingke 1st Street, Nanshan District, Shenzhen, Guangdong,

China, 518055

WLAN frequency range: 2400 MHz - 2483.5 Mhz.

Maximum transmission power: < 20dBm

Wireless Standard: IEEE802.11b/g/n

Power Supply: DC 12V 2.0A 24W (NVR)

DC 12V 1.0A 12W (IPC)

NVR Upgrade:

Download the rmware to the U disk Insert U disk to NVR →

USB port Right-click click→ → Main Menu →Upgrade →

Refresh Upgrade → click to upgrade your NVR.

IPC Upgrade:

Download the rmware to the U disk Insert U disk to NVR USB →

port Right-click → → Main Menu →IPC Cong Maintenance→

→ → click Refresh click to update this camera or click CH Select

All to upgrade your all cameras.

IPC Restore default:

Right-click →Main Menu →IPC Cong Maintenance→ →

click to restore default this camera or click to CH Select All

restore default your all cameras.

Note:

Don't shut down the power during upgrade. After upgrading,

NVR restarts.

Product Performance

3. Device Adding: Once logged in, you can tap the "+" button

on the APP, after that scan the QR code, which is located

at the bottom of your NVR.

Foscam VMS

Foscam VMS is a new tool for PC. It does not require plug-ins and

is compatible with Windows & Mac, It supports all Foscam HD

cameras and up to 36 cameras at the same time. If you would

like to manage multiple cameras, we suggest you install the

Foscam VMS. You can download the “Foscam VMS” from

foscam.com/vms, and can download the "Foscam VMS" Mac

version from the APP store:

https://apps.apple.com/cn/app/foscamvms/id1521202507?mt=12

Add the NVR

1. Run Foscam VMS, then you can create a local administrator

account and login.

2. Tap the "+" button on the Foscam VMS and follow the setup

wizard to add your NVR.

Please refer to the user manual for more detailed adding steps.

3. Preview: click device in Lan Device list to enter preview

interface, select a channel to view it’s picture, click to

enter , as follow shows:

2. You can upgrade the rmware of your NVR and cameras with

Foscam App.

Open Foscam APP and Login the NVR, select Settings > NVR

Firmware Camera Firmware or Upgrade.

3. You can upgrade the rmware of your NVR and cameras with

Foscam VMS.

Open and Login Foscam VMS, select Setup > > System

System Upgrade Camera Upgrade or .

Note:

In all upgrade methods, don't shut down the power during

upgrade. After upgrading, NVR restarts.

6. Motion Detection Record

Right-click → Main Menu →IPC Cong Advanced → →

Motion Detect Enable Choose → → Set Sensitivity & Region &

Body Filter & Body Rectangle . →Apply

7. Auto Bridge

By new mesh network auto-bridging function, without any

manual setting, wireless camera in further area will have a

judgment about the WIFI signal and auto connect to the

camera which have a better WIFI signal, to achieve more stable

and reliable video transmission.

Auto bridging is designed to expand the coverage area of

wireless signal, instead of enhancing the signal. When camera is

a little far away from NVR, or there are too many interference

factors/sources between them, camera in further area will auto

bridge/connect to the one nearby to transmit the video data.

① → → Right click Pair IP Camera Repeater.

② Then, bridging relationship will be showed on the interface

automatically.

1.Click the button to select

the rmware to the U disk

2.Click the button to

Upgrade

1.Click the button to select

the rmware to the U disk

2.Choose the channel camera

you need to upgrade

3. Click the button to

Upgrade

1.Choose the channel camera

you need to Restore

2. Click the button to

Restore

Note: For the best experience, please update Foscam VMS to the

latest version!

Firmware upgrade step:

① Click " " button to downloadDownload the latest rmware

the latest rmware to your computer.

② Click " " button , choose le rmware version youBrowse

want to upgrade on the web page.

③ Click " " button and wait till it's nished.Upgrade

Basic

Device Manager

Application

System

Factory Reset

Camera Firmware

Reboot

NVR Firmware

Current firmware version 2.71.1.79：

Download the latest firmware

Browse

Device Settings

Upgrade 3

FN7108W

FN8108H

smartphone, or scan the QR Code on the below, it will take

you to the download page to install the . Foscam APP

② → → → Playback: Right-click Main Menu Playback choose

channel and date click timeline to check record.→

5. Backup

Insert U disk to NVR USB port Right-click → → Main Menu →

Backup Search → → choose channel, type and time select →

target le →Backup

Note: EmptyIf target le can not be searched out, please click →

Add. Please remove the les which is no need before backup.

Ensure insert device (like USB) in 30 second, as system reserved

searching time for it is 30 second.

Produktspezifikationen

Marke:	Foscam
Kategorie:	Nicht kategorisiert
Modell:	FN8108W-B4

Brauchst du Hilfe?

Wenn Sie Hilfe mit Foscam FN8108W-B4 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Foscam

Foscam FN8108W-B4 Bedienungsanleitung

4 September 2024

Foscam FN9108E-B4 Bedienungsanleitung

25 August 2024

Foscam FN9108H Bedienungsanleitung

25 August 2024

Foscam FNA108H Bedienungsanleitung

25 August 2024

Foscam FN9108HE Bedienungsanleitung

25 August 2024

Foscam T8EP Bedienungsanleitung

24 August 2024

Foscam T5EP Bedienungsanleitung

24 August 2024

Foscam FNA108HE Bedienungsanleitung

26 Februar 2024

Foscam FN7104W-B4 Bedienungsanleitung

10 November 2022

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024