FoodSaver GameSaver Pro Plus Bedienungsanleitung
FoodSaver
Vakuumfüller
GameSaver Pro Plus
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für FoodSaver GameSaver Pro Plus (4 Seiten) in der Kategorie Vakuumfüller. Dieser Bedienungsanleitung war für 21 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/4
Features
For important safety information and helpful tips, please refer to the FoodSaver ®Reference Guide
included with your appliance. Questions? Visit us at www.foodsaver.com or call 1-800-777-5452 (U.S.)
or 1-877-804-5383 (Canada). Get tips on vacuum packaging and order FoodSaver ®accessories.
Roll Storage
Compartment
Removable
Vacuum Channel
Rubber Gasket
Sliding Door to
Vacuum Channel
Sealing Strip
L
K
N
J
M
Features of Your GameSaver®Appliance
Tips
Additional Features & Tips
For more usage tips and safety information, please refer to the FoodSaver®Reference Guide or visit our website at www.foodsaver.com.
Tips on Sealing a Bag
Make sure you’ve placed the bag in the proper
place. When making a bag from a roll, make sure end
of cut piece is on Sealing Strip (N), not over rubber
gasket (L) or in Vacuum Channel (K).
Prevent moisture or liquid from being pulled
into the Vacuum Channel or trapped in the
seal. Either pre-freeze moist foods such as raw
meat for 1-2 hours before vacuum packaging, or
place a folded paper towel between food and end of
bag to absorb excess liquids. Be sure to leave at least
3 inches between paper towel and end of bag so that
bag seals properly with paper towel inside.
Make sure the Seal Control Switch (E) is set to
the appropriate position.
Make sure you give appliance time to cool
down. Wait at least 20 seconds between seals.
Under very heavy usage, appliance will shut off
automatically to prevent overheating. If it does, wait
20 minutes to allow appliance to cool off.
Tips on Removing Air from a Bag
Make sure you’ve placed the bag in the proper
place. When vacuum packaging make sure open end
of bag is inside Vacuum Channel (K). Also make sure
roll itself is tucked back into Roll Storage
Compartment (J) or it could prevent appliance from
operating properly.
Check for wrinkles in the bag along the Sealing
Strip. Wrinkles in seal may cause leakage and allow
air to come back into bag. Check for wrinkles in bag
along Sealing Strip (N) before closing lid and vacuum
packaging. If you find wrinkles after sealing bag,
simply cut bag open and vacuum package again.
If motor runs for more than 30 seconds with-
out stopping, you may need to adjust bag and try
again. If you are making initial seal on a piece of bag
material with two open ends, make sure bag is placed
on Sealing Strip, not in Vacuum Channel (K). If you
are vacuum packaging with a bag, make sure open
end is placed down inside Vacuum Channel and make
sure Accessory Hose (B) is not attached. If you are
vacuum packaging with an accessory, check Accessory
Hose in appliance lid and in accessory to ensure a
tight fit. Make sure Seal Control Switch (E) is set to
appropriate position.
General Tips
Tips for Successful Vacuum Packaging
(continued)
1. Vacuum packaging is NOT a substitute for the
heat process of canning. Perishables still need to
be refrigerated or frozen.
2. For best results, use FoodSaver®Bags, Canisters
and Accessories.
3. During the vacuum packaging process, small
amounts of liquids, crumbs or food particles can
be inadvertently pulled into Vacuum Channel (K),
clogging the pump and damaging your appliance.
To prevent this, follow these tips:
a. For moist and juicy foods such as raw meats:
Freeze first and avoid overfilling bags. You can
also place a folded paper towel inside top of bag,
but below seal area, before vacuum packaging.
b. For soups, sauces and liquids: Freeze first and
avoid overfilling bags. Or, use a canister in
refrigerator.
c. For powdery or fine-grained foods: Avoid
overfilling bags or use a canister. You can also
place a coffee filter or paper towel inside
before vacuum packaging.
d. If your appliance features a Removable
Vacuum Channel (K), empty and clean after
each use.
4. To avoid overfilling, always leave at least 3 inches
of bag material between bag contents and top of
bag. Then leave at least one additional inch of bag
material for each time you plan to reuse bag.
5. Do not create your own side seams for a
FoodSaver®Bag. These bags are manufactured
with a special side seam, which is sealed all the
way to the outer edge.
6. To prevent wrinkles in seal when vacuum
packaging bulky items, gently stretch bag flat
along Sealing Strip (N) before you close lid.
7. If you are unsure your bag was sealed properly,
simply reseal bag about 1⁄ 4 inch above first seal.
8. When you are vacuum packaging items with sharp
edges (dry spaghetti, silverware, etc.), protect
bag from punctures by wrapping item in soft
cushioning material, such as a paper towel. You
may want to use a canister or Mason jar instead
of a bag.
9. When using accessories, remember to leave one
inch of space at top of canister or container.
10. Pre-freeze fruits and blanch vegetables before
vacuum packaging for best results. See pages 2-3
of FoodSaver®Reference Guide for more
information.
© 2007 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved.
First Printing: 03/07 Item # 9100060001017 (03/07)
QuickStart
GameSaver®Pro Plus
Accessory Hose Storage
Accessory Hose
Cancel Button
Instant Seal Button
Seal Control Switch
(5-Position)
Indicator Light
Pulse Button
Accessory Port
Bag Cutter
H
A
B
D
E
C
I
G
F
The Removable Vacuum Channel makes cleanup(K)
easy when small amounts of liquids are inadvertently
pulled into the Vacuum Channel during vacuum
process. (See FoodSaver®Reference Guide for tips on
preventing this.)
After each use, slide open side door (M) on right side
of appliance and pull Vacuum Channel out. Remove
rubber gasket (L) and wipe gasket with damp cloth.
Empty Vacuum Channel and wash in warm soapy
water or place on top rack of dishwasher. Dry
thoroughly before re-inserting into appliance.
Appliance cannot be used without Vacuum Channel
in place.
Removable Vacuum Channel
GS Pro.qxd:QS.1505_GSpro_v3.qxd 4/19/07 4:00 PM Page 5
And More
Bags & Rolls
Pulse Mode allows you maximum control over the
vacuum process for crushable items in bags. After
placing bag in Vacuum Channel (K) and closing lid,
follow these instructions:
1. Set Seal Control Switch (E) to Pulse Mode.
2. Press down firmly on lid to activate motor, then
release.
3. Press Pulse Button (G) and hold for as long as
desired, then release. Indicator Light (F) will flash
quickly after Pulse Button is used. To remove
more air, simply repeat Step 3.
4. After removing desired amount of air, press
Instant Seal Button (D) to seal bag. Indicator Light
will flash slowly when bag is sealing.
5. When motor and light turn off, vacuum process
is complete.
Tip: When using Pulse Mode, you MUST
MUST
MUST
MUST MUST press
Instant Seal Button to seal bag. If there is no activity
for 30 seconds, appliance will shut off automatically
and bag will not be sealed.
The Instant Seal Button (D) stops the vacuum
process early and seals the bag, preventing delicate
foods such as cookies from being crushed.
1. Vacuum package as described in previous sections.
2. To stop process before all air is removed, press and
release Instant Seal Button. Vacuum process will
stop within a few seconds and bag will be sealed.
3. When motor and Indicator Light (F) turn off,
open lid and remove bag.
The Instant Seal Button is also used to end Pulse
Mode (see instructions above).
If you want to seal a bag without vacuuming, use the
Seal Only position on the Seal Control Switch (E).
You can even reseal bags such as Mylar®potato chip
bags.
1. Place open end of bag on Sealing Strip (N) and
close lid.
2. Set Seal Control Switch to Seal Only.
3. Press down firmly on lid with both hands until
motor starts, then release. Motor and Indicator
Light (F) will turn on, indicating bag is sealing.
4. When motor and Indicator Light turn off, open lid
and remove bag.
Note: If Sealing Strip is too hot for a mylar bag, try
setting Seal Control Switch to instead of Seal
Only. As long as you place open end of bag on
Sealing Strip (not in Vacuum Channel), no air will be
removed.
1
Additional Features
Pulse Mode
Instant Seal
Seal Only
1. Place item(s) in bag, allowing at least 3 inches
of space between bag contents and top of bag.
2. Open appliance lid and place open end of bag
down into Vacuum Channel (K). Make sure roll
material is tucked backed into Roll Storage
Compartment (J) or it could prevent the
appliance from operating properly.
3. Close lid.
4. Set Seal Control Switch (E) to:
to vacuum package using FoodSaver®bags
(medium seal time).
to vacuum package moist and juicy foods
such as raw meat (longer seal time).
5. To begin vacuum process, press down firmly
on lid with both hands until motor starts, then
release. Motor will continue to run.
6. When motor and Indicator Light (F) turn off,
vacuum and seal process is complete. Open lid and
remove bag. Refrigerate or freeze if needed. (See
FoodSaver®Reference Guide for food safety tips.)
3
2
1. Open appliance lid and place roll into Roll Storage
Compartment (J).
2. Pull out enough bag material to hold item to be
vacuum packaged, plus at least 3 inches. Close lid.
3. Turn Seal Control Switch (E) to .Seal Only
4. Press down firmly on lid with both hands until
motor starts, then release lid. Motor and Indicator
Light (F) will turn on as bag material is sealing.
5. When motor and light turn off, cut bag material by
pressing down lightly on lid and sliding Bag Cutter
(I) from one end of sliding channel to other end.
6. Open lid, remove bag, and tuck roll back into Roll
Storage Compartment before vacuum packaging.
Now you are ready to vacuum package with your
new bag (see below).
Getting Started
Registering your appliance is quick and easy at www.foodsaver.com.
Accessories
FoodSaver®Accessory Guidelines
FoodSaver®Accessories
1. Always leave at least one inch of space between
contents and rim.
2. Wipe rim of canister, container or bottle to ensure
it is clean and dry.
3. Place lid on canister or container, or place stopper
in bottle.
4. For accessories with a large knob on lid, turn knob
to Vacuum. Vacuum package using instructions
below. When vacuum process is complete, turn
knob to Closed before removing Accessory Hose.
5. For accessories without a large knob on lid,
vacuum package using instructions below.
How to Open FoodSaver®Accessories after Vacuum Packaging
FoodSaver Vacuum Packaging Canisters
(without large knob on lid)
To release vacuum and open, push gray rubber
button on lid.
FoodSaver Bulk Canisters and Quick
Marinators (with large knob on lid) and
Universal Lids
To release vacuum and open, turn knob on lid
to Open.
FoodSaver Jar Sealer with Mason Jars
For use with Ball®and Kerr ® brand Mason jars.
IMPORTANT: Do NOT use screw bands when
vacuum packaging jars. To open, wedge spoon
between Mason jar lid and highest part of threaded
rim. Twist spoon gently to release vacuum.
FoodSaver Bottle Stoppers
To release vacuum and open, twist and pull up on
Bottle Stopper.
How to Vacuum Package with FoodSaver®Accessories
1. Prepare container according to FoodSaver®
Accessory Guidelines above.
2. Insert one end of Accessory Hose (B) into
Accessory Port (H) on appliance. Insert other
end into port on accessory. Twist tab on
Accessory Hose while inserting to ensure a tight fit.
3. Turn Seal Control Switch (E) to .
4. To begin vacuum process, press down firmly on
lid until motor starts, then release. Motor will
continue to run.
5. When motor and Indicator Light (F) turn off,
vacuum process is complete.
6. Gently twist and remove Accessory Hose from
accessory and appliance.
7. To test vacuum, simply tug on accessory lid. It
should not move.
Note: For important tips on using accessories
with different foods, please refer to the FoodSaver®
Reference Guide.
1
How to Make a Bag from a FoodSaver®Roll
How to Vacuum Package with FoodSaver®Bags
Pull Out Bag Material Set Seal Control Switch Press and Release Lid
Place Bag in Vacuum Channel Set Seal Control Switch Press and Release Lid
Insert Accessory Hose Set Seal Control Switch Press and Release Lid
GS Pro.qxd:QS.1505_GSpro_v3.qxd 4/19/07 4:00 PM Page 2
Produktspezifikationen
| Marke: | FoodSaver |
| Kategorie: | Vakuumfüller |
| Modell: | GameSaver Pro Plus |
Brauchst du Hilfe?
Wenn Sie Hilfe mit FoodSaver GameSaver Pro Plus benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Vakuumfüller FoodSaver
29 Mai 2024
9 Mai 2024
21 April 2024
31 März 2024
30 März 2024
14 März 2024
20 Februar 2024
15 Februar 2024
23 Januar 2024
Bedienungsanleitung Vakuumfüller
- Vakuumfüller Domo
- Vakuumfüller Emerio
- Vakuumfüller G3 Ferrari
- Vakuumfüller SilverCrest
- Vakuumfüller Sunbeam
- Vakuumfüller Guzzanti
- Vakuumfüller Princess
- Vakuumfüller AEG
- Vakuumfüller Alfa
- Vakuumfüller Ambiano
- Vakuumfüller Ardes
- Vakuumfüller Asko
- Vakuumfüller ATAG
- Vakuumfüller Buffalo
- Vakuumfüller Caso
- Vakuumfüller Concept
- Vakuumfüller Ellrona
- Vakuumfüller Gaggenau
- Vakuumfüller Klarstein
- Vakuumfüller Koenic
- Vakuumfüller Miele
- Vakuumfüller Proficook
- Vakuumfüller Rommelsbacher
- Vakuumfüller Sammic
- Vakuumfüller Severin
- Vakuumfüller Solis
- Vakuumfüller Unold
- Vakuumfüller Gastroback
- Vakuumfüller Hendi
- Vakuumfüller Korona
- Vakuumfüller Steba
- Vakuumfüller Taurus
- Vakuumfüller Eta
- Vakuumfüller Krups
- Vakuumfüller Smeg
- Vakuumfüller Trebs
- Vakuumfüller Brandt
- Vakuumfüller Bartscher
- Vakuumfüller Neff
- Vakuumfüller V-ZUG
- Vakuumfüller Laica
- Vakuumfüller Leifheit
- Vakuumfüller Rotel
- Vakuumfüller Gemini
- Vakuumfüller Imetec
- Vakuumfüller Champion
- Vakuumfüller Vacmaster
- Vakuumfüller JML
- Vakuumfüller OBH Nordica
- Vakuumfüller Peach
- Vakuumfüller Royal Sovereign
- Vakuumfüller Fisher & Paykel
- Vakuumfüller Orbegozo
- Vakuumfüller Emga
- Vakuumfüller Tilia
- Vakuumfüller Zepter
- Vakuumfüller Berkel
- Vakuumfüller Magic Vac
- Vakuumfüller Nesco
- Vakuumfüller Nutrichef
- Vakuumfüller CalmDo
- Vakuumfüller VacPak-It
- Vakuumfüller Weston
- Vakuumfüller Catler
- Vakuumfüller Anova
- Vakuumfüller Flaem-Nuova
- Vakuumfüller Flaem
- Vakuumfüller Luvele
- Vakuumfüller Create
Neueste Bedienungsanleitung für -Kategorien-
25 Juni 2024
13 Juni 2024
4 Juni 2024
28 Mai 2024
22 Mai 2024
22 Mai 2024
9 Mai 2024
30 April 2024
30 April 2024
18 April 2024