Fluke 7102 Bedienungsanleitung
Fluke
Temperaturregeln
7102
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Fluke 7102 (6 Seiten) in der Kategorie Temperaturregeln. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/6
1
Introduction
The Fluke Calibration 7102/7103 Micro-Bath (The Product) is a portable and bench-top
temperature calibrator that calibrates thermocouple and RTD temperature probes. For complete
Product use instructions, download the 7102 User’s Guide or the 7103 User’s Guide from
www.flukecal.com.
Note
The Product CD no longer ships with these Products.
Contact Fluke Calibration
Fluke Corporation operates worldwide. For local contact information, go to our website:
www.flukecal.com
To register your product, view, print, or download the latest User’s Guide or manual supplement, go
to our website.
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
+1-425-446-5500
info@flukecal.com
7102/7103
Micro-Bath
Safety Information
1-year limited warranty. See the User’s Guide for the full warranty.
PN 5311971
August 2021
© 2021 Fluke Corporation. All rights reserved. Specifications are subject to change without notice.
All product names are trademarks of their respective companies.
7102/7103
Safety Information
2
Safety Information
More specific safety information is listed in the User’s Guide where applicable.
A Warning identifies hazardous conditions and procedures that are dangerous to the user.
XW Warning
To prevent possible electrical shock, fire, or personal injury:
• Read all safety information before you use the Product.
• Carefully read all instructions.
• Use this Product indoors only.
• Do not use the Product if it operates incorrectly.
• Follow local regulations regarding use with toxic, flammable, corrosive, or
otherwise hazardous fluids. Incorrect product installation, abuse, or damage can
lead to operator exposure to these fluids. Limit hazardous-fluid exposure to
permitted levels in case of leakage or rupture.
• Do not operate the Product in an excessively wet, oily, dusty, or dirty environment.
• Do not use the Product if it is altered or damaged.
• Disable the Product if it is damaged.
• Replace the mains power cord if the insulation is damaged or if the insulation
shows signs of wear.
• Make sure that the power cord is positioned in such a way as it cannot contact hot
surfaces or temperature probes. Always inspect power cord before use for any
damage to the insulation due to contact with hot surfaces, cuts or abrasions.
• Do not alter the Product and use only as specified, or the protection supplied by
the Product can be compromised.
• Do not use the Product around explosive gas, vapor, or in damp, dusty, or wet
environments.
• Do not use the Product above its rated frequency.
• Connect an approved three-conductor mains power cord to a grounded power
outlet.
• Do not put the Product where access to the mains power cord is blocked.
• Make sure that the space around the Product meets minimum requirements. Leave
at least 15 cm (6 inches) of clearance around the Product.
• Do not use an extension cord or adapter plug.
• Do not keep the Product in operation and unattended at high temperatures.
• Turn the Product off and remove the mains power cord. Stop for two minutes to let
the power assemblies discharge before you open the fuse door.
• Replace a blown fuse with exact replacement only for continued protection
against arc flash.
• Turn off the Product and remove the mains power cord. Stop for 2 minutes to let
the internal circuits discharge before you open the fuse door or remove Product
covers.
• Have an approved technician repair the Product.
Micro-Bath
Safety Information
3
• Do not install an access cover without holes onto a bath that is energized.
Dangerous pressures may result from fluid vaporizing.
• Do not use the Product for any application other than calibration work. The
Product is for temperature calibration only. Any other use of the unit may cause
unknown hazards to the user.
• To move the Product, lift the Product by the handle provided. Do not move the
Product until the display reads <25 °C (77 °F) and the Product has been drained or
the transport lid installed.
• Always ensure the Product is cool before you close it for storage.
• Do not touch the well access surface of the Product.
• Do not mix water and oil when exceeding temperatures of 90 °C (194 °F). The
temperature of the well access is the same as the actual temperature shown on
the display. For example, if the Product is set at 125 °C (257 °F) and the display
reads 125 °C, the well is at 125 °C (257 °F).
• Do not operate near flammable materials. Extreme temperatures could ignite the
flammable material.
• The top sheet metal of the Product may exhibit extreme temperatures for areas
close to the well access.
• Do not turn off the unit at temperatures >100 °C (212 °F). This could create a
hazardous situation. Select a set-point <100 °C (212 °F) and allow the Product to
cool before you turn it off.
• Do not remove the fluid at high temperatures. The fluid will be the same
temperature as the display temperature.
• Use of this Product at high temperatures for extended time periods requires
caution.
• Always operate this Product at room temperatures listed in Environmental
Conditions in the User’s Guide.
• Overhead clearance is required. Do not place the Product under a cabinet or other
structure.
• Use a ground fault interrupt device.
• Fluids may expand at different rates. Allow for fluid expansion inside the well by
Keeping the fluid level at least 1.9 cm (0.75 inches) below the top of the well at all
times.
Produktspezifikationen
| Marke: | Fluke |
| Kategorie: | Temperaturregeln |
| Modell: | 7102 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Fluke 7102 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Temperaturregeln Fluke
9 April 2024
2 Juni 2023
20 Oktober 2022
15 Oktober 2022
Bedienungsanleitung Temperaturregeln
- Temperaturregeln Panasonic
- Temperaturregeln AEG
- Temperaturregeln Techno Line
- Temperaturregeln Technoline
- Temperaturregeln Ventus
- Temperaturregeln Honeywell
- Temperaturregeln Kathrein
- Temperaturregeln Dimplex
- Temperaturregeln JUNG
- Temperaturregeln Carel
- Temperaturregeln AstralPool
- Temperaturregeln SRS
- Temperaturregeln Emko
- Temperaturregeln Jumo
Neueste Bedienungsanleitung für -Kategorien-
28 Mai 2024
28 Mai 2024
24 Mai 2024
3 Mai 2024
31 März 2024
13 März 2024
7 März 2024
24 Februar 2024
21 Februar 2024
20 Januar 2024