Fire-Lite SD365CO Bedienungsanleitung

Fire-Lite Detektor SD365CO

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Fire-Lite SD365CO (4 Seiten) in der Kategorie Detektor. Dieser Bedienungsanleitung war für 40 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

plications, refer to NFPA 72 or the System Smoke Detector Application Guide,

available from FireLite.

WIRING GUIDE

All wiring must be installed in compliance with the National Electrical Code,

applicable local codes, and any special requirements of the Authority Having

Jurisdiction. Proper wire gauges should be used. The installation wires should

be color-coded to limit wiring mistakes and ease system troubleshooting.

Improper connections will prevent a system from responding properly in the

event of a fire.

Remove power from the communication line before installing sensors.

1. Wire the sensor base (supplied separately) per the base wiring diagram.

(See Figure 1.)

2. Set the desired address on the sensor address switches. (See Figure 2.)

3. Install the sensor into the sensor base. Push the sensor into the base

while turning it clockwise to secure it in place.

4. After all sensors have been installed, apply power to the control panel

and activate the communication line.

5. Test the sensor(s) as described in the TESTING section of this manual.

FIGURE 1. WIRING DIAGRAM

(–)

(+)

+ -

UL LISTED COM TIBLEPA

CONTROL NELPA

CLASS A OPTIONAL WIRING

REMOTE

ANNUNCIATOR

(–)

(+)

C0129-04

CAUTION

Do not loop wire under terminal 1 or 2. Break wire run to provide supervision

of connections.

FIGURE 2. ROTARY ADDRESS SWITCHES

TENS ONES

910

3210

C0162-00

SPECIFICATIONS

Operating Voltage Range: 15 to 32 VDC

Operating Current @ 24 VDC: 200 uA (one communication every 5 seconds with green LED blink on communication)

Maximum Alarm Current: 2 mA @ 24 VDC (one communication every 5 seconds with red LED solid on)

Maximum Current: 4.5 mA @ 24 VDC (one communication every 5 seconds with amber LED solid on)

Operating Humidity Range: 15% to 90% Relative Humidity, Non-condensing

Operating Temperature Range: 32°F to 100°F (0°C to 38°C)

Air Velocity: 0 to 4000 ft./min. (0 to 1219.2 m/min.)

Height: 2.7" (69 mm) installed in B200S series sounder base

Diameter: 6.875" (175 mm) installed in B200S series sounder bases

Weight: 3.4 oz. (95 g)

Isolator Load Rating: 0.0063*

*Please refer to your isolator base/module manual for isolator calculation instructions.

UL 2075 listed for Carbon Monoxide

UL 268 listed for Open Air Protection

UL 521 listed for Heat Detectors

This sensor must be installed in compliance with the control panel sys-

tem installation manual. For local audible indication of a fire and/or

carbon monoxide alarm, it is recommended to install the multi-criteria

carbon monoxide (CO) and smoke sensors into a B200S series sounder

base. If a local audible device is not used, care should be taken to de-

velop a proper response plan. The installation must meet the require-

ments of the Authority Having Jurisdiction (AHJ). Sensors offer maximum

performance when installed in compliance with the National Fire Protec-

tion Association (NFPA); see NFPA 72 and NFPA 720. For a complete list

of compatible bases, refer to the Base/Sensor Cross Reference Chart at

systemsensor.com.

GENERAL DESCRIPTION

Model SD365CO is a plug-in type multi-criteria smoke sensor that offers a

photoelectric sensing chamber combined with a carbon monoxide (CO) sen-

sor, 135°F (57.2°C) fixed temperature heat detector and infrared (IR) sensors,

as well as, a carbon monoxide detector. The SD365CO also transmits an alarm

signal due to heat (135°F/57.2°C) per UL 521.

All sensors transmit an analog representation of smoke and/or carbon monox-

ide density over a communication line to a control panel. Rotary dial switches

are provided for setting the sensor’s address. (See Figure 2.)

Two LEDs on the sensor are controlled by the panel to indicate sensor status.

An output is provided for connection to an optional remote LED annunciator

(P/N RA100Z).

FireLite panels offer different features sets across different models. As a result,

certain features of the photoelectric sensors may be available on some control

panels, but not on others.

The multi-criteria CO and smoke sensors only support LiteSpeed protocol sys-

tems. The possible features available in the multi-criteria CO and smoke sen-

sors, if supported by the control unit are:

1. The sensor’s LEDs can operate in three ways—on, off, and blinking—and

they can be set to red, green, or amber. This is controlled by the panel.

2. The remote output may be synchronized to the LED operation or con-

trolled independent of the LEDs.

3. Devices are point addressable up to 159 addresses.

Please refer to the operation manual for the UL listed control panel for specific

operation. The photoelectric sensors require compatible addressable com-

munications to function properly. Connect these sensors to listed-compatible

control panels only.

SPACING

FireLite recommends spacing sensors in compliance with NFPA 72. In low air

flow applications with smooth ceilings, space sensors 30 feet apart (9.1 m).

For specific information regarding sensor spacing, placement, and special ap-

I56-6601-001

INSTALLATION AND MAINTENANCE INSTRUCTIONS

SD365CO

Multi-Criteria CO and Smoke Sensor

One FireLite Place

Northford, CT 06472

Phone: 203.484.7161

1 I56-6601-001

4/22/2019

FIGURE 3. FEATURES OF THE FIRE/CO DETECTOR

Base Alignment Notch

Infrared

Light

Pipe

CO Test Point

Magnet Test Point

Thermistors

Infrared

Light

Pipe

LEDs

C2043-00

FIGURE 4. CLEANING THE FIRE/CO DETECTOR

Cover

Removal

Tabs

Sensor Cover

Sensing Chamber

Cover and Screen

Infrared

Light

Pipe

Thermistors

Sensing

Chamber

}

C2044-00

CAUTION

Dust covers provide limited protection against airborne dust particles during

shipping. Dust covers must be removed before the sensors can sense smoke.

Remove sensors prior to heavy remodeling or construction.

TAMPER RESISTANCE

Model SD365CO includes a tamper-resistant capability that prevents removal

from the base without the use of a tool. Refer to the base manual for details on

making use of this capability.

TESTING

Before testing, notify the proper authorities that the system is undergoing

maintenance, and will temporarily be out of service. Disable the system to

prevent unwanted alarms.

All sensors must be tested after installation and periodically thereafter. Test-

ing methods must satisfy the Authority Having Jurisdiction (AHJ). Sensors

offer maximum performance when tested and maintained in compliance with

NFPA 72. Sensitivity readings are available through the FACP. Refer to the

manufac turer’s published instructions for proper use.

The sensor can be tested in the following ways:

A. Functional: Magnet Test (P/N M02-04-01 or M02-09-00)

This sensor can be functionally tested with a test magnet. The test mag-

net electronically simulates smoke in the sensing chamber, testing the

sensor electronics and connections to the control panel.

a. Hold the test magnet in the magnet test area as shown in Figure 3.

b. The sensor should alarm the panel.

Two LEDs on the sensor are controlled by the panel to indicate sensor

status. Coded signals, transmitted from the panel, can cause the LEDs

to blink, latch on, or latch off. Refer to the control panel technical docu-

mentation for sensor LED status operation and expected delay to alarm.

NOTE: The magnet test initiates an approximately 10 minute period

when the detector's signal processing software routines are not active.

B. Smoke Entry

Canned aerosol simulated smoke (canned smoke agent) may be used for

smoke entry testing of the smoke detector.

The multi-criteria CO and smoke sensor uses algorithms to process sig-

nals received from multiple sensors to determine alarm conditions and

reduce false alarms. Therefore, a single burst of canned smoke will not

immediately place the detector into an alarm condition because the de-

tector algorithms correctly determine a burst of canned smoke is not fire.

In order to perform functional testing of the photoelectric sensor, the

device must be placed into test mode. Test mode allows the detector to

isolate the individual sensors for testing. The device can be placed into

test mode through either of the following methods.

a. Put the device into test mode by holding a test magnet in the magnet

test area as shown in Figure 3 for 6-12 seconds.

NOTE: If the magnet is held in place for too long the fire alarm test func-

tion will be triggered. (See Magnet Test, above.) Reset the panel and

proceed with testing the smoke entry portion of the device.

b. Perform smoke entry testing immediately following the magnet test.

The magnet test initiates an approximately 10 minute period when the

detector’s signal processing software routines are not active.

Once in test mode, test the smoke detector using one of the tested and ap-

proved aerosol smoke products. Refer to the manufacturer’s published instruc-

tions for proper use of the canned smoke agent. When used properly, the

canned smoke agent will cause the smoke detector to go into alarm.

Tested and approved aerosol smoke products include:

Manufacturer Model

HSI Fire and Safety 25S, 30S (PURCHECK)

SDi SMOKE CENTURION , SOLOA10,

SMOKESABRE, TRUTEST, SOLO 365

No Climb TESTIFIRE 2000

CAUTION

Canned aerosol simulated smoke (canned smoke agent) formulas will vary

by manufacturer. Misuse or overuse of these products may have long term

adverse effects on the smoke detector. Consult the canned smoke agent manu-

facturer’s published instructions for any further warnings or caution statements.

C. Direct Heat Method (Hair Dryer of 1000-1500 watts)

A hair dryer of 1000-1500 watts should be used to test the thermistors.

Direct the heat toward the thermistor, holding the heat source approxi-

mately 12 inches (30 cm) from the detector in order to avoid damaging

the plastic housing. The detector will reset only after it has had sufficient

time to cool. Make sure both thermistors are tested individually.

D. Multi-Criteria Testing

Testifire® by SDi provides testing of the smoke, heat and CO sensors. Consult

the manufacturer’s published instructions for complete usage instructions.

A sensor that fails any of these tests may need to be cleaned as described

under CLEANING, and retested. When testing is complete, restore the system

to normal operation and notify the proper authorities that the system is back

in operation.

E. Functional Gas Test

NOTE: Check with local codes and the AHJ to determine whether or not

a functional gas test is desired for an installation.

A canned CO testing agent may be used to verify the detector’s ability to

sense CO. Carbon Monoxide alarm thresholds are designed around CO

concentrations over time, as defined in UL standard 2034. Therefore, a

single burst of CO test agent will not immediately place the detector into

an alarm condition. In order to perform functional testing of the CO sen-

sor, the device must be placed into test mode. Test mode eliminates the

time and concentration requirements needed for alarm and allows the

CO sensor to be tested. The device can be placed into test mode through

either of the following methods.

a. Put the device into test mode by holding a test magnet in the magnet

test area as shown in Figure 3 for 6-12 seconds.

NOTE: If the magnet is held in place for too long the fire alarm test func-

tion will be triggered. Reset the panel and proceed with testing the CO

portion of the device.

b. Perform functional gas entry testing immediately following the magnet

test. The magnet test initiates an approximately 10 minute period when

the detector's signal processing software routines are not active.

Once in test mode, test the CO sensor using a tested and approved

canned CO testing agent. A tested and approved canned CO testing agent

is Solo detector testers model C6 CO Detector Tester available from SDi.

Complete the CO sensor testing as follows:

Spray a UL approved CO agent into the top of the detector near the CO

sensor opening for at least 1 second. CO sensor opening is indicated by

2 I56-6601-001

4/22/2019

a triangle on the sensor cover. (See Figure 3.) Use the applicator straw

included with the CO agent to more efficiently direct the CO into the

detection cell during testing.

The detector will go into alarm if gas entry is successful. It may take up

to 1 minute for the device to alarm. Once the detector is in alarm allow

5 minutes for the CO to clear and exit the detector.

The detector will automatically enable the signal processing after 10 min-

utes.

Testing the detector will activate the alarm relay and send a signal to

the panel.

CLEANING

Before removing the detector, notify the proper authorities that the smoke

detector system is undergoing maintenance and will be temporarily out of

service. Disable the zone or system undergoing maintenance to prevent un-

wanted alarms.

1. Remove the sensor to be cleaned from the system.

2. Remove the sensor cover by pressing firmly on each of the four removal

tabs that hold the cover in place. (See Figure 4.)

3. Vacuum the screen carefully without removing it. If further cleaning is

required continue with Step 4, otherwise skip to Step 7.

4. Remove the chamber cover/screen assembly by pulling it straight out.

5. Use a vacuum cleaner or compressed air to remove dust and debris from

the sensing chamber.

6. Reinstall the chamber cover/screen assembly by aligning the arrows on

the top with the two round-top posts on the sensing chamber, and gently

pressing it until it fits securely.

7. Replace the cover using the LEDs to align the cover and then gently

pushing it until it locks into place. NOTE: Make sure that the thermistors

do not become bent under the cover.

8. Reinstall the detector.

9. Test the detector as described in TESTING.

10. Reconnect disabled circuits.

11. Notify the proper authorities that the system is back on line.

ABOUT CARBON MONOXIDE DETECTORS

CAUTION

CAUTION: This carbon monoxide detector is designed for indoor use only.

Do not expose to rain or moisture. Do not knock or drop the detector. The

detector will not protect against the risk of carbon monoxide poisoning if

not properly wired. The detector will only indicate the presence of carbon

monoxide gas at the sensor. Carbon monoxide gas may be present in other

areas.

This carbon monoxide detector is NOT:

• Designed to detect any gas other than carbon monoxide

• To be seen as a substitute for the proper servicing of fuel-burning appli-

ances or the sweeping of chimneys.

• To be used on an intermittent basis, or as a portable alarm for the spill-

age of combustion products from fuel-burning appliances or chimneys.

Carbon monoxide gas is a highly poisonous gas which is released when fuels

are burnt. It is invisible, has no smell and is therefore impossible to detect

with the human senses. Under normal conditions in a room where fuel burn-

ing appliances are well maintained and correctly ventilated, the amount of

carbon monoxide released into the room by appliances should not be danger-

ous.

SYMPTOMS OF CARBON MONOXIDE POISONING

Carbon monoxide bonds to the hemoglobin in the blood and reduces the

amount of oxygen being circulated in the body. The following symptoms

are examples taken from NFPA 720. They represent approximate values for

healthy adults:

Concentration (ppm CO) Symptoms

200 Mild headache

after 2-3 hours of exposure

400 Headache and nausea

after 1-2 hours of exposure

800 Headache, nausea, and dizziness

after 45 minutes of exposure;

collapse and unconsciousness

after 2 hours of exposure

Many causes of reported carbon monoxide poisoning indicate that while vic-

tims are aware that they are not well, they become so disoriented that they

are unable to save themselves by either exiting the building or calling for

assistance.

Also young children and pets may be the first to be affected.

Per UL standard 2075, the SD365CO has been tested to the sensitivity limits

defined in UL standard 2034.

ALARM THRESHOLDS ARE AS FOLLOWS:

Parts Per Million Detector response time, min.

70 ±5ppm 60-240

150 ±5ppm 10-50

400 ±10ppm 4-15

What to do if the carbon monoxide detector goes into alarm:

Immediately move to a spot where fresh air is available, preferably out-

doors.

IMPORTANT: This detector should be tested and maintained regularly fol-

lowing National Fire Protection Association (NFPA) 720 requirements.

CO SENSOR LIFETIME

The CO cell has an expected lifetime of approximately ten years. The detector

is programmed to signal the approach of end of this lifetime to the control

panel. The CO cell is not a field replaceable component. The smoke sensor

will continue to operate using other sensing elements (photoelectric, heat and

infrared) even though the CO cell is no longer operational. The CO detector

will not operate once the CO cell has reached its end of life.

SPECIAL NOTE REGARDING SMOKE DETECTOR GUARDS

Smoke detectors are not to be used with detector guards unless the combina-

tion has been evaluated and found suitable for that purpose.

3 I56-6601-001

4/22/2019

Produktspezifikationen

Marke:	Fire-Lite
Kategorie:	Detektor
Modell:	SD365CO

Brauchst du Hilfe?

Wenn Sie Hilfe mit Fire-Lite SD365CO benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Detektor Fire-Lite

Fire-Lite SD365CO Bedienungsanleitung

22 Juni 2023

Bedienungsanleitung Detektor

Neueste Bedienungsanleitung für -Kategorien-

Alecto HA-58 Bedienungsanleitung

4 Oktober 2024

Amprobe ULD-400-T Bedienungsanleitung

1 Oktober 2024

Hager EE809 Bedienungsanleitung

22 September 2024

DSC RM-2 Bedienungsanleitung

14 September 2024

K40 Platinum200 Expert Bedienungsanleitung

12 September 2024

K40 Platinum360 Expert Bedienungsanleitung

12 September 2024

K40 RL200di Bedienungsanleitung

12 September 2024

Noyafa NF-820 Bedienungsanleitung

6 September 2024

STI BIO-7505 Bedienungsanleitung

6 September 2024

Soler & Palau CPTA Bedienungsanleitung

6 September 2024