Extron TLP Pro 725T Bedienungsanleitung

Extron Monitor TLP Pro 725T

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Extron TLP Pro 725T (4 Seiten) in der Kategorie Monitor. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

TLP Pro 725T Series and

TLP Pro 1025T Series • Setup Guide

Overview

The TLP Pro 725T series are 7-inch tabletop capacitive touchscreens with a resolution of 1024x600 and 24-bit color depth. The

TLP Pro 1025T series are 10-inch tabletop capacitive touchscreens with a resolution of 1280x800 and 24-bit color depth.

All these models can be placed on any convenient at surface.

This guide provides instructions for experienced installers to install these touchpanels. For complete instructions, see the

TLPPro 725 and TLP Pro 1025 Series User Guide, at www.extron.com.

Setup Checklist

Get Ready

Download and install the latest version of the following software:

GUI Designer — for designing layouts for Extron TouchLink® Pro touchpanels and third party touch interfaces.

Global Configurator® Professional Global Configurator Plusor — for setting up and conguring the control processor

and touchpanel.

Toolbelt — provides device discovery, device information, rmware updates, and conguration of network settings,

system utilities, and user management for TouchLink Pro devices.

Global Scripter® — provides an integrated development environment for Extron control systems programming.

NOTE: All four software programs are available from www.extron.com.

Obtain the following network information from your network administrator:

DHCP status (on or off). If DHCP is off, you must also obtain:

IP address Subnet mask Gateway

User name — this can be either or .

Password — by default this is (for either admin or user).

Make a note of the touchpanel MAC address.

Mount and Cable All Devices

ATTENTION:

• Do not power on the touchpanels or control processors until you have read the ATTENTION in the “Base” section of

the or the .TLP Pro 725 and TLP Pro 1025 Series User Guide IPCP Pro User Guide or IPL Pro User Guide

• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «Base » du

TLP Pro 725 and TLP Pro 1025 Series User Guide IPCP Pro User Guide or IPLProUserGuide ou du .

Mount the units. There are several mounting options for TouchLink Pro touchpanels (see on the next page).Mounting

Connect the touchpanel to a Power over Ethernet injector (not provided). Extron recommends the XTP PI 100 power injector,

which can be purchased separately.

Connect the power injector to the LAN and power it on.

Set up the Touchpanels for Network Communication

Connect the PC that you are using for setup, the control processor, and touchpanel .to the same Ethernet subnetwork

Use the (see page 4) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask, Setup Menu

gateway, and related settings for the touchpanel.

Conﬁgure the Touchpanels

The , the , and the GUI Designer Help File Global Conﬁgurator Help File Toolbelt Help File provide step-by-step instructions

and more detailed information. The includes an introduction to the software and sections on Global Conﬁgurator Help File

how to start a project and conguration. Global Scripter provides an Extron-exclusive Python library (ControlScript®) and

Global Scripter modules to get you started.

Product Category

IMPORTANT:

Go to for the

complete user guide and installation

instructions befor

e connecting the

oduct to the power sou

rce.

www.extron.com

Mounting

The base allows these touchpanels to be placed on any suitable at surface.

For additional security, the touchpanels can be attached to a table or desktop.

1. Connect an Ethernet cable to the LAN/PoE input (see , ﬁgure 3 F, on the next page) and run the cable through the cable

guide (D).

2. Drill two holes through the desktop from underneath, 3.07” (78 mm) apart

3. Attach the touchpanel with two #8-32 screws through the desktop from underneath into the two mounting holes in the base

of the unit (A).

The touchpanels can also be mounted with the optional Extron SMA-2 swivel mount adapter, which allows them to be secured

to the table and swivel up to 180° in either direction. Attach the SMA-2 to the mounting holes in the base (

A) and follow the

instructions in the .SMA-2 Swivel Mount Adapter Kit User Guide

Front Panel Features

Figure 1 shows the TLP Pro 725T series front panel. The front panel of the TLP Pro 1025T series is very similar.

BB CC

Figure 1. TLP Pro 725T Front Panel

A LCD touchscreen

TLP Pro 725T series — 7-inch, 1024x600 resolution touchscreen

TLP Pro 1025T series — 10-inch, 1280x800 resolution touchscreen

The touchscreen is made with Corning Gorilla Glass, which is stronger and more scratch-resistant than standard glass, while

maintaining touch sensitivity, color saturation, and brightness.

B (2) — Detects motion between three to ve feet from the touchpanel, and at least 15° from the center axis.Motion sensor

zWhen no motion has been detected for a user-dened period of time, the touchpanel enters sleep mode.

zWhen motion is detected by the sensor, the screen display is restored and active.

C — Shows the conguration and connection status of the touchpanel:Communication LED

zUnlit during normal operation (the touchpanel is congured and connected to an IP Link Pro control processor).

zBlinks red if the touchpanel has been congured but is not connected to an IP Link Pro control processor.

zSolidly lit if the touchpanel has not been congured.

The indicator can be toggled between enabled and disabled, using the (see page 4). Setup Menu

D — Monitors ambient light level and adjusts screen brightness, based on the settings congured using the Light sensor

Setup Menu.

E — Can be programmed to provide system feedback:Status light

zLight red or green

zBlink or light continuously

For information about programming this light, see the or the .Global Conﬁgurator Help File Global Scripter Help File

TLP Pro 725T Series and TLP Pro 1025T Series • Setup Guide (Continued)

Rear Panel Features

BB CC

Figure 2. TLP Pro 725T Rear Panel

A — Can be programmed to provide system feedback:Status light

• Light red or green Blink or light continuously•

For information about programming this light, see the or the .Global Conﬁgurator Help File Global Scripter Help File

B — Compatible with USB 2.0. The port is concealed behind a plastic cover, which can be removed with a small, USB-A port

at-bladed screw driver.

C — The LAN/PoE cable is inserted through this hole at the back of the base (see below).Cable guide LAN/PoE connector

Base

Figure 3 shows the base of the TLP Pro 725T series models. The base of the TLP Pro 1025T series models are very similar.

FFAA BB DD E

E G

GCC AA

Figure 3. TLP Pro 725T Base

A (2) — See on the previous page.Mounting hole Mounting

B — Activates the setup menu (see on Menu button Setup Menu

the following page).

C — Initiates one of three reset modes for the unit Reset button

(see on the following page).

Reset Modes: a Brief Summary

D — The LAN/PoE cable is inserted through this hole Cable guide

at the back of the base.

E — Indicates power status and reset status of the Reset LED

device (see on the following

Reset Modes: a Brief Summary

page).

F — Attach the LAN/PoE cable to this RJ-45 LAN/PoE Connector

port. The power injector must be purchased separately. Figure 4

shows the Extron XTP PI 100. Your power injector may look

different.

Connect a straight-through Ethernet cable from the power

injector to a switch or router (see gure 4, 1). This cable

carries network information from the switch or router to the

power supply input. A second straight-through cable carries the

network information and 48VDC from the power injector to the

touchpanel (2). Connect the IEC power cord to a convenient

100 VAC to 240 VAC, 50-60 Hz power source (3).

G — A single speaker provides audible feedback for the Speaker

user.

ATTENTION:

• Do not power on the touchpanels or control processors until you have read the ATTENTION in the “Base” section of

the .TLP Pro 725 and TLP Pro 1025 Series User Guide

• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «Base » du

TLP Pro 725 and TLP Pro 1025 Series User Guide.

100-240V

50-60Hz

0.4A MAX

XTP

PWR

XTP PWR

To network switch To touchpanel

1 2

Figure 4. Connecting to a Power Injector

NOTE: Figure 2 shows the TLP Pro 725T series rear panel.

The TLP Pro 1025T series rear panels are very similar.

Product Category

Produktspezifikationen

Marke:	Extron
Kategorie:	Monitor
Modell:	TLP Pro 725T
Touchscreen:	Ja
Bildschirmdiagonale:	7 "
Bildschirmtechnologie:	LCD
Eingebautes Mikrofon:	Nein
Eingebaute Lautsprecher:	Ja
Integrierte Kamera:	Nein
Produktfarbe:	Schwarz
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Warentarifnummer (HS):	85285210
Bildschirmform:	Flach
Helligkeit:	420 cd/m²
Kontrastverhältnis:	700:1
Bildwinkel, horizontal:	75 °
Bildwinkel, vertikal:	75 °
Anzahl der Lautsprecher:	1
Gewicht (ohne Ständer):	790 g
Breite (ohne Standfuß):	180.9 mm
Tiefe (ohne Standfuß):	89.8 mm
Höhe (ohne Standfuß):	121.5 mm
Speicherkapazität:	2048 MB
Wandmontage:	Nein
NVIDIA G-SYNC:	Nein
AMD FreeSync:	Nein
Anzahl der nachgeschalteten Steckplätze vom Typ USB-A:	1
Touchscreen Technologie:	Kapazitiv
Display-Auflösung:	1024 x 600 Pixel
Ethernet/LAN:	Ja