Esotec Siena Bedienungsanleitung

Esotec Nicht kategorisiert Siena

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Esotec Siena (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/5
Instruction manual
Solar pond pump set
Napoli LED, Napoli LED top and Siena LED
These instructions relate ONLY to this product and contain important informa-
tion for using the product for the first time. Please keep these instructions for
later reference and should always accompany the product in the event of trans-
ference to a new user.
1. Introduction
Dear Costumer, thank you for purchasing the solar pump kit.
With this solar pump kit you purchased a product manufactured according to the cur-
rent state of technology.
This product fulfils all requirements of the valid European and national regula-
tions. The conformity was proved. The relevant declarations and documentati-
on are deposited with the manufacturer.
To maintain this state and guarantee a safe operation, you as the user will have to fol-
low this operating manual!
2. Safety Instructions
- In case of damages caused by not following
this operating manual, the warranty rights
will expire! We exclude liability for any
consequential damages!
- We exclude liability for property or
personal damages caused by inappropriate
handling or not following the safety instructions.
- In these cases any guarantee rights will expire.
Due to safety and admission reasons (CE) it is not allowed to arbitrarily reconstruct
and/or change the solar pump kit.
Therefore, please keep to the operating manual.
The accident prevention rules of the association of the industrial trade cooperative
association for electric plants and working material are to be considered in industrial
environments
3. Appropriate Use
- The pumping system is designed for the outdoor use in garden ponds. The accu-
mulator storage is charged during sunshine. The solar pump may be switched
“on” “off”and via a switch. An LED-display informs you about the charge condi-
tion of the accumulator.
- Direct solar radiation is required for the correct function.
- The pumping system is characterized by its easy assembly. Tools are not requi-
red for the assembly.
- The pump must not be used for the raising of drinking water.
- The performance may be adjusted via a controller on the pump.
- In order to avoid any disturbing gurgling, simply attach fewer standpipes to the
pump.
- In order to safely interrupt the pumping it is required to interrupt the cable connec-
tion between solar module and pump.
4. Assembly/installation and start of operation
For the details of assembly/installation and start of operation, please see the instruc-
tion manuals of the accumulator box and the pond pump.
5. Service and Maintenance
In order to preserve the performance of the pump, it is required to wash out the pump
and its parts with warm water depending on the pollution of the water.
For directions for the service and maintenance of the pump and accumulator storage,
please see the instruction of the pump and accumulator storage.
Occasionally wipe the solar module clean with a soft and slightly moistened cloth.
Note: Before carrying out operations on the pump, interrupt the plug connection bet-
ween pump and battery pack in order to avoid any unintentional starting during the
operations.
6. Technical Data
Solar pumping system Napoli LED Napoli LED top Siena LED
- System voltage: 12 -24 VDC 12 -24 VDC 12 -24 VDC
Solar module
- Nominal power: 10 Wp 20 Wp 20 Wp
- Nominal voltage: 17,5 V 17 V 17 V
- Nominal current: 580 mA 1,2 A 1,2 A
- Open-circuit voltage: 21,6 V 21 V 21 V
- Short-circuit current: 680 mA 1,32 A 1,32 A
- Projection system: IP 65 IP 65 IP 65
- Temperature range: -30°C to +75°C -30°C to +75°C -30°C to +75°C
- Dimensions: 440 x 255 x 25 mm 530 x 360 x 25 mm 530 x 360 x 25 mm
Water pump:
- Operating voltage: 12 to 24 V DC 12 to 24 V DC 12 to 24 V DC
- Power consumption (12/24V): 3 W/ 12 W 3 W/ 12 W 5 W/ 22 W
- Max. delivery height (12/24V): 0,8 m/ 2 m 0,8 m/ 2 m 0,9 m/ 2,8 m
- Delivery rate (12/24V): 470 l/h/ 750 l/h 470 l/h/ 750 l/h 900 l/h/ 1500 l/h
- Protection system: IP 68 IP 68 IP 68
- Temperature range: +4 to +40°C +4 to +40°C +4 to +40°C
- Dry running: dry protected dry protected dry protected
Accumulator storage:
- Accumulator (lead gel): 12V/ 7Ah 12V/ 7Ah 12V/ 7Ah
- Output voltage: 12 to 24 VDC 12 to 24 VDC 12 to 24 VDC
- Runtime with fully charged
accumulator: max. 13 h max. 13 h max. 6 h
- Max. module capacity: 20 Wp (36 cells) 20 Wp (36 cells) 20 Wp (36 cells)
- Max. output current: 800 mA 800 mA 800 mA
Attention: Do not put the housing into the blazing sun! Overheating risk!
LED Light ring:
- Illuminants: 6 LEDs 6 LEDs 6 LEDs
- Operating voltage: 12 to 24 VDC 12 to 24 VDC 12 to 24 VDC
- Protection class: IP 68 IP 68 IP 68
- Operating temperature range: +4 to +40°C +4 to +40°C +4 to +40°C
Note: Protect the pump from frost!
In cold winter months, it is required to take the pump out of the water and store it in
a warm place. The solar module may be left outside during the winter.
7. Safety Instructions:
DANGER for children! Keep children away from swallowable small parts (ascending
pipe and sprinklers) and the packaging material. Danger of suffocation!
WARNING: risk of stumbling! Lay the connecting cable so that it will not become a
trip hazard!
CAUTION Material damage! When setting up the solar module without module brak-
ket, please pay attention to an adequate stability. The solar module may be damaged
in case of tipping or in case of an impact of a foreign object.
Disposal instruction for electric appliances:
Dear customer, if you want to get rid of the article, please dispo-
se it according to the current regulations. The municipal authori-
ty will provide you with information.
Manufacturer:
esotec GmbH
Gewerbegebiet Weberschlag 9
D-92729 Weiherhammer
Tel.-Nr: +49 (0)9605-92206-28
Fax.-Nr: +49 (0)9605-92206-10
e-mail:info@esotec.de
Internet: www.esotec.de
Additional parts:
5 m extender cable for water pump and solar module: 101738
5 m extender cable for fountain light: 101740
Copyright esotec GmbH
!
GB
Customer support:
If you have problems or questions regarding this product, simply contact us!
Monday to Friday 8 am to 12 noon and 1 pm to 4 pm.
By phone: 09605-92206-27
By e-mail for ordering spare parts: ersatzteil@esotec.de
By e-mail for questions about the product: technik@esotec.de
Product manufacturer item No.:
solar pump system Napoli LED: 101773
solar pump system Napoli LED top: 101776
solar pump system Siena LED: 101780
Operating manual
These instructions relate ONLY to this product and contain important informa-
tion for using the product for the first time. Please keep these instructions for
later reference and should always accompany the product in the event of trans-
ference to a new user.
1. Introduction
Dear Costumer,
Thank you for purchasing the solar light. With this solar light you purchased a product
manufactured according to the current state of technology.
This product fulfils all requirements of the valid European and national regula-
tions. The conformity was proved. The relevant declarations and documentati-
on are deposited with the manufacturer.
To maintain this state and guarantee a safe operation, you as the user will have to fol-
low this operating manual!
2. Safety Instructions
- In case of damages caused by not
following this operating manual, the
warranty rights will expire! We exclude
liability for any consequential damages!
- We exclude liability for property or
personal damages caused by inappropriate
handling or not following the safety instructions.
- In these cases any guarantee rights will expire.
Due to safety and admission reasons (CE) it is not allowed to arbitrarily reconstruct
and/or change the solar light.
Therefore, please keep to the operating manual.
The accident prevention rules of the association of the industrial trade cooperative
association for electric plants and working material are to be considered in industrial
environments.
3. Intended use
This submersible pump is designed for pumping water in garden ponds, fountains,
water dishes, etc. It can pump water through a hose connection or can be operated
through attached lifting tubes with water sprinklers.
A solar module or a power pack with a voltage of 12 to 24 volts can be used as the
energy source. When used with a solar module, the pump works only if enough
solar radiation strikes the solar module.
A battery box (accessory) is delivered along with this pump. When battery is on, an
LED light (accessory) can be attached to the lifting tube. This gives the fountain a
decorative lighting. The LED light rings are available in different colours.
The delivery rate of the pump can be adjusted using the regulator on the front side
of the pump. The water pump has no On/Off switch. As soon as the pump is con-
nected to its power supply, it starts pumping water.
4. Installation and commissioning
1. Roll out the connecting cable of the
pump completely.
2. Ensure that the cap is firmly in place on
the socket.
3. Place the pump in water (please note
Point 5 here).
4. Connect the lifting tubes till they project
out of the water surface. For this, first
attach the reducer to the pump.
5. You can now choose from 2 different
water nozzles.
6. Alternatively, the pump can also be used
for pumping water through a hose. For
this, you just have to attach a hose to the
pumpĘĽs pipe.
7. Now supply power to the water pump
through a solar module. Use the enclo-
sed plug with cable (red = positive pole,
black = negative pole) for this. If you
have purchased this pump as a complete
solar power system, then the appropriate
plug is already attached to the solar module.
Note: The plug has reverse-polarity protection, no force should be used while inser-
ting. The glass of the solar module is fragile.
Caution! Risk of injury! A broken module cannot be repaired again and must be dis-
posed off in an environmental-friendly way.
8. If the pumping capacity is too high, you can reduce the amount of water. Simply
turn the regulator on the front side of the pump in clockwise direction. Please
do not use force while adjusting. The adjustment range is 45°.
4.1 Operation with LED light ring
The accessories include a LED light ring. This light ring can be easily slipped onto
the lifting tube.
Electrical connection is established via the socket on the pump. For this, remove
the drain plug, insert the light ring plug in the socket and tighten the cap nut firmly.
5. Dry run protection
The pump is equipped as standard with a dry run protec-
tion. Two sensor points are provided on the side of the
housing for this. The pump works if these points are
under water. If a point projects out of the water, the pump
does not work.
6. Care and maintenance
For optimum performance of the pump, it must be washed occasionally with warm
water depending on the water contamination. To wash the pump, open the housing
as follows:
Note: Please do not use force while dismantling or assembling the pump. The parts
are very fragile and can break easily.
1. Disconnect the pumpĘĽs plug.
2. Pull the front cover of the pump forward like a slide gently (Figure 1).
3. Turn the front cover of the pump by about 45° clockwise (Figure 1) and carefully
pull the cover forward (Figure 2). Watch out for the plastic shaft and the seal while
doing this.
4. Carefully drag the impeller out of the pump (if necessary, use pliers). (Figure 3).
5. Now clean all the parts carefully with warm water.
6. Then plug the shaft with the impeller carefully into the hole of the pump. Ensure
that the shaft is fitted firmly.
7. Now place the cover carefully over the pump. Ensure that the seal is fitted proper-
ly.
8. Turn the front cover again by 45 degrees counter-clockwise into the starting posi-
tion.
9. Slide the lower part of the pump completely into the pump housing.
The pump is ready to use again.
7. Malfunction
Pump is not pumping water
- Is the pump completely submerged in water? Dry run protection (Point 5)
- Is the polarity of the supply voltage reversed? Cable colour brown = + pole,
blue = negative pole
- Is the pump dirty? Cleaning the pump, see Point 6.
8. Technical data
Operating voltage: 12 - 24 V DC
Degree of protection: IP 68
Power consumption: Approx. 5 W at 12 VDC - approx. 22 W at 24 VDC
Pump lift: Max. 0.9 m at 12 VDC - max. 2,8 m at 24 VDC
Delivery rate: Max. 900 l/h at 12 VDC - max. 1500 l/h at 24 VDC
Operating temp. range: +4 to +40°C
Note: The pump is only suitable for pumping water.
Note: Protect the pump from frost!
During cold winter months, the pump must be taken out of the water and
placed/stored in a warm area. The solar module can spend the winter outdoors.
!
GB
Sensorpoints
lifting tubes
water nozzle
water nozzle
lifting tubes
Customer support:
If you have problems or questions regarding this product, simply contact us!
Monday to Friday 8 am to 12 noon and 1 pm to 4 pm.
By phone: 09605-92206-27
By e-mail for ordering spare parts: ersatzteil@esotec.de
By e-mail for questions about the product: technik@esotec.de
Product: Manufacturer Item No.: 101758
turn 45°
12
3
Drain plug
Light ring
connection
9. Safety information:
DANGEROUS for children! Children could easily swallow the small parts that come
with this pump and its packaging material. Please keep at a safe distance. These
parts could otherwise lead to choking or suffocation!
WARNING against danger of stumbling! Lay out the connection cable such that it
does not create the threat of tripping or stumbling!
CAREFUL: material damage! If you set up the solar module without a module hold-
er, you must make sure that it is sturdy enough to retain its position. If the module falls
down or a foreign object hits against it, the solar module can be damaged.
10. Spare parts
1. White ceramic shaft: Item No.: 911040
2. Pump impeller: Item No.: 911041
3. Internal rubber bush: Item No.: 911042
4. Front cover: Item No.: 911043
5. Seal for cover: Item No.: 911044
6. Sliding carriages with suction bases: Item No.: 911045
7. Suction bases (4 pieces) Item No.: 911046
8. Complete nozzle set: Item No.: 911047
Manufacturer/Importer
esotec GmbH - Gewerbegebiet Weberschlag 9 - D-92729 Weiherhammer
Tel.-Nr: 09605-92206-0 - Fax.-Nr: 09605-92206-10 - Internet: www.esotec.de
Disposal:
Dear customer,
please cooperate in avoiding waste. When you intend to dispose of the product in
future, please consider that it contains valuable raw materials suited for recycling.
Therefore, do not dispose it of with domestic waste but bring it to a collection point
for the recycling of waste electrical and electronic equipment.
Thank you very much for your cooperation!
Copyright, esotec GmbH
1
2
3inside 4+5 6
77
3inside
11. Accessories
11.1 extender cable (5 m) for water pump
Item-no: 101738
11.2 battery box 12 V/ 7 Ah
Item-no: 101734
- The battery station can be used in the esotec pumping systems Verona,
Toskana, Napoli, Napoli LED, Siena and Siena LED.
- The accumulator box is installed between pump and solar module.
- The pump may be switched-on and –off via a switch.
- The installed accumulator is protected against under- and overcharge.
- Two LEDs inform you about the condition of the accumulator.
- The system is ready to plug-in and is set up in a matter of minutes.
11.3 light rings (only in combination with battery box)
LED light ring white (with 6 weißen LED´s) Item-no: 101790
LED light ring yellow (with 6 yellow LED´s) Item-no: 101791
LED light ring blue (with 6 blue LED´s) Item-no: 101792
LED light ring green (with 6 green LED´s) Item-no: 101793
LED light ring red, green, blue (with each 2 LED´s) Item-no: 101794
5 m Extender cable for light rings Item-no: 101740

Produktspezifikationen

Marke: Esotec
Kategorie: Nicht kategorisiert
Modell: Siena

Brauchst du Hilfe?

Wenn Sie Hilfe mit Esotec Siena benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert Esotec

Esotec

Esotec Palermo LED Bedienungsanleitung

23 August 2024
Esotec

Esotec Palermo Bedienungsanleitung

23 August 2024
Esotec

Esotec Palermos-S Bedienungsanleitung

23 August 2024
Esotec

Esotec Siena Bedienungsanleitung

12 Mai 2024
Esotec

Esotec Garda Bedienungsanleitung

12 August 2023
Esotec

Esotec Rimini Plus Bedienungsanleitung

28 April 2023

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024