Emga 710110 Bedienungsanleitung
Emga
Bordsteinwärmer
710110
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Emga 710110 (17 Seiten) in der Kategorie Bordsteinwärmer. Dieser Bedienungsanleitung war für 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/17
710110 en ma ev ol 2014
INSTRUCTIONS
ASSEMBLY, INSTALLATION, USE AND MANTEINANCE.
Ed. 03/2012
The producer decline every responsibility on any print and/or transcription mistake contained in this booklet
The producer can change features and datas of this booklet with the proposal of keeping on increase the quality of its products.
Anytime and without notice, this booklet can’t be considered as contract with third parties.
1
Item:
*710.110 1/1 GN
Summary
1. Instruction Warnings ........................................................................................................2
2. Safety and Right Use Warnings.......................................................................................2
3. Warran .2 ty .........................................................................................................................
4. Installation........................................................................................................................3
4.1 Techn eatures .4 ical F ....................................................................................................
4.2 Assembly....................................................................................................................4
4.3 Componen .5 ts..............................................................................................................
5. .............................................................................................Cleaning ancean end Maint .6
5.1 Breakdowns .6 ..............................................................................................................
5.2 Electrical scheme .......................................................................................................7
6 s. Di po .8 sal ..........................................................................................................................
710110 en ma ev ol 2014
INSTRUCTIONS
ASSEMBLY, INSTALLATION, USE AND MANTEINANCE.
Ed. 03/2012
The producer decline every responsibility on any print and/or transcription mistake contained in this booklet
The producer can change features and datas of this booklet with the proposal of keeping on increase the quality of its products.
Anytime and without notice, this booklet can’t be considered as contract with third parties.
2
1. Instruction Warnings
The final user has to hold the whole instructions. User must store up this document
in case of use. Producer do not assume any responsibility for damages incurred due to the
failure of improper use of this manual.
All measures in this manual are in mm.
2. Safety and Right Use Warnings
This product meets the latest technological evolutions and current
safety guidelines.
The carving stations with infrared lamps, object of this booklet, is
projected to be in compliance with directives and field laws, in order to
guarantee a safe and reliable product.
Any other use will be considered inapposit to the original destination.
Producer do not assume any responsibility for damages caused by an improper use.
Responsibility lies only on user.
A proper use also includes compliance with the instructions for use and installation
and any additional documentation as well as the conditions of inspection and
maintenance.
3. Warranty
This product is designed and produced for a professional environment. Due to
commercial and construction requirements, the manufacturer reserves the right to make
changes in order to enhance the quality and use of product. The producer, in compliance
with European Community legislation, guarantees its products for 24 months. This
guarantee does not include electrical parts, labor and all replacements related to an
improper use of the good.
Any manipulation carried out automatically excludes the liability of the manufacturer.
The products or parts to be replaced or repaired for unequivocal defects in workmanship
and materials used must be in a “free port” at the offices of the producer, who after a
careful inspection, will repair or replace them. The repairs are carried out exclusively at the
headquarters of the manufacturer, and none cost incurred by the customer for repairs will
be refunded by the manufacturer unless expressly agreed.
710110 en ma ev ol 2014
INSTRUCTIONS
ASSEMBLY, INSTALLATION, USE AND MANTEINANCE.
Ed. 03/2012
The producer decline every responsibility on any print and/or transcription mistake contained in this booklet
The producer can change features and datas of this booklet with the proposal of keeping on increase the quality of its products.
Anytime and without notice, this booklet can’t be considered as contract with third parties.
3
4. Installation
The manufacturer declines every responsibility of damage of someone
or something caused by the failure to comply with the instructions of this
manual.
After the unpacking of the item from its packing, proceed by removing
the adhesive plastic tape before sarting up the product. Any residual glue has
to be removed carefully (do not use abrasive cleaners).
The assembly for the end use concerns only to the infrared bulbs that have to be
screwed-in inside the specific ceramic lampholder, and to the protection domes to be fixed
with the provided screws following the scheme at page 4.
The device is designed to run on AC to the voltage specified on the technical data
plate (located on the bottom of the unit).
The grounding line is marked by the colours yellow/green and must not be
interrupted.
The device is provided with a cable in accordance with the CE regulations and with
has CE and schuko plug (that can be replaced, when necessary, with a different plug,
suitable for the specified wattage and in accordance to the current regulations and
guidelines; when necessary, replace the provided cable with a new one with the same
features).
Before switching the applicance:
• Check if the electrical system can withstand the appliance’s load (WATT as indicated
on the techical plate)
• Make sure that the electrical system is provided with ground connection according to
the current norms and guidelines.
• Connect the device to the grounding network through a cable which has to be
connected to the specified screw located on the external casing of the device itself.
(Component n. 22, see exploded view page 5).
To switch on the device, turn the thermostat knob on the required temperature (max 90°)
then the indicator light will turn on and when the right temperature is reached it will turn
off; through the thermostat the selected temperature will be preserved.
Turn the knob to the position “0” (OFF) to switch off the device.
The infrared lamps have an independent system and are managed from the switch
located on the top of the device.
WARNING:
Once turned on, the appliance will reach the desired temperature
very quickly. In order to avoid any inconvenience, turn the device on
only shortly before starting the service and turn it off shortly after the
end. Do not make any structural change to the appliance.
Produktspezifikationen
Marke: | Emga |
Kategorie: | Bordsteinwärmer |
Modell: | 710110 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Emga 710110 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Bordsteinwärmer Emga
28 August 2024
Bedienungsanleitung Bordsteinwärmer
- Bordsteinwärmer Domo
- Bordsteinwärmer Emerio
- Bordsteinwärmer Gaggenau
- Bordsteinwärmer Bartscher
- Bordsteinwärmer Suntec
- Bordsteinwärmer CaterChef
- Bordsteinwärmer Accucold
Neueste Bedienungsanleitung fĂĽr -Kategorien-
29 September 2024
29 September 2024
15 August 2024
10 August 2024
7 August 2024
4 August 2024
1 August 2024
30 Juli 2024
29 Juli 2024
19 Juli 2024