EMG 81 Bedienungsanleitung

EMG Nicht kategorisiert 81

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für EMG 81 (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 25 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/3
INSTALLATION INFORMATION
EMG MODELS: EMG-H, HA, 58, 60, 60A, 81, 85
Warra nty
All EMG Pickups and accessories are warranted for a period of two years. This warranty does not cover failure due to improper installation, abuse or damage. If
upon examination the pickup is determined to be defective, a replacement will be made. Warranty replacement products are covered by this same warranty. This
warranty covers only those pickups and accessories sold by authorized EMG Dealers. This warranty is not transferable.
© 2009 Copyright EMG INC. All Rights Reserved.
PO BOX 4394
SANTA ROSA, CA
95402 USA
P (707) 525-9941
F (707) 575-7046
EMGPICKUPS.COM
0230-0106revD
*Note: Logo Colors are not distinguished on Chrome and Gold Models
**Note: Magnet Type: A (Alnico) A/S (Alnico/Steel) C (Ceramic) C/S (Ceramic/Steel)
Installation notes:
All EMG Pickups are compatible with each other. The connector system is an easy method of installation, avoiding the need to solder.
Older systems may need to be soldered, while the newer systems can be easily connected and modified. If you have an older EMG
Pickup you can install the new system along with it.
EMG accessories like the VLPF, EXG, SPC or RPC Controls can be added to any EMG Pickup System without the need for an extra battery.
SPECIFICATIONS: MODEL :
H HA 58 60 60A 81 85
Logo Color* White Gold Gold Grey Gold Silver Gold
Magnet Type ** C A A/S C A C/S A
Resonant Frequency (KHz) 4.05 3.70 1.53 2.20 1.80 1.63 1.87
Output Voltage (String) 1.00 1.00 3.00 3.00 3.00 3.00 3.10
Output Voltage (Strum) 3.00 3.00 4.50 4.50 4.50 4.50 4.50
Output Noise (60 Hz) -101 -101 -100 -101 -100 -100 -101
Output Impedance (Kohm) 10 10 10 10 10 10 10
Current @9V (Microamps) 80 80 80 80 80 80 80
Battery Life (Hours) 3000 3000 3000 3000 3000 3000 3000
Maximum Supply (Volts DC) 27 27 27 27 27 27 27
IMPORTANT INSTALLATION NOTES:
1) Only one 9-Volt battery is required to power the pickups and any
accessories such as the SPC, RPC, EXG, AB, PA-2, and Pi-2.
Use an Alkaline or Lithium battery for longest life.
2) The Volume and Tone controls included with this EMG System are
25K Ohm. This value is required for the system to work correctly.
3) A stereo output jack (12B) is included with the EMG Pickups;
it grounds the black battery wire to turn on the pickups when
the plug is inserted into the jack. If you are replacing passive
pickups, make sure to use the jack included. If your guitar has a
long panel jack (see Page 2, bottom), make sure it is a stereo
type, a Switchcraft 152B is recommended.
4) When installing EMG Active Pickups, DO NOT connect the bridge
ground wire. This wire is usually soldered to a volume or tone
control casing and goes to the bridge. This wire grounds the
strings and uses them and your body as a shield against hum and
buzz. It also creates a shock hazard.
EMG Pickups are shielded internally and DO NOT require string
grounding. This greatly reduces the possibility of reverse
polarity shock from microphones and other equipment.
5) EMG Active Pickups have very little magnetism compared to
passive pickups. We recommend you adjust the pickups as
close to the strings as possible. Sustain and string movement
will not be inhibited by close adjustment.
6) If your installation is different from the diagrams in these
instructions or you need additional diagrams visit our website:
emgpickups.com for a complete listing of available diagrams.
7) SPECIAL NOTE:
The diagrams shown are for EMG Active Pickups.
All diagrams show the Red Wire coming from the pickups
connected to the battery. If you are installing EMG-HZ
Passive Pickups refer to their diagrams. The Red Wire of
the HZ Pickup is NOT for battery power, it is a coil wire.
2.75
1.50
3.08
3/48 MOUNTING HOLES
.900 .725
Installation Instructions:
EMG Models: EMG-H, HA, 58, 60, 60A, 81, 85
H INSTRUCTIONS Page 3
BRIDGE PICKUP (POSITION 1)
NECK PICKUP (POSITION 2)
OUTPUT (POSITION 3)
NECK PICKUP
BRIDGE PICKUP
Diagram #6b
2 Pickups
Toggle Style Select Switch
Master Volume & Master Tone
MASTER
TONE
FROM NECK PICKUP
FROM BRIDGE PICKUP
BATTERY
NEG (-)
MASTER
VOLUME OUTPUT
T
R
S
OUTPUT CABLE
****Tips and Tricks****
****Tips and T
****Tips and T
****Tips and T
****Tips and Tricks****
ricks****
ricks****
ricks****
Start your installation by:
Start your installation by:
Start your installation by:
Start your installation by:
Start your installation by:
1) Read the General Notes on Page 2 if you haven’t already
1) Read the General Notes on Page 2 if you haven’t already
1) Read the General Notes on Page 2 if you haven’t already
1) Read the General Notes on Page 2 if you haven’t already
1) Read the General Notes on Page 2 if you haven’t already
and determine if you have the right output jack for your
and determine if you have the right output jack for your
and determine if you have the right output jack for your
and determine if you have the right output jack for your
and determine if you have the right output jack for your
instrument. A Stereo 12B type (Included) or a 152B Long Panel
instrument. A Stereo 12B type (Included) or a 152B Long Panel
instrument. A Stereo 12B type (Included) or a 152B Long Panel
instrument. A Stereo 12B type (Included) or a 152B Long Panel
instrument. A Stereo 12B type (Included) or a 152B Long Panel
Jack will be required.
Jack will be required.
Jack will be required.
Jack will be required.
Jack will be required.
2) Remove the strings
2) Remove the strings
2) Remove the strings
2) Remove the strings
2) Remove the strings
3) Remove any existing Pickups and controls
3) Remove any existing Pickups and controls
3) Remove any existing Pickups and controls
3) Remove any existing Pickups and controls
3) Remove any existing Pickups and controls
(remember the order and function of each control)
(remember the order and function of each control)
(remember the order and function of each control)
(remember the order and function of each control)
(remember the order and function of each control)
4) Determine a good spot for the Pickup Buss and make sure the
4) Determine a good spot for the Pickup Buss and make sure the
4) Determine a good spot for the Pickup Buss and make sure the
4) Determine a good spot for the Pickup Buss and make sure the
4) Determine a good spot for the Pickup Buss and make sure the
cable or wires from the selection switch will reach the Pickup Buss,
cable or wires from the selection switch will reach the Pickup Buss,
cable or wires from the selection switch will reach the Pickup Buss,
cable or wires from the selection switch will reach the Pickup Buss,
cable or wires from the selection switch will reach the Pickup Buss,
5) Install the EMG Volume and Tone Controls and tighten them in.
5) Install the EMG Volume and T
5) Install the EMG Volume and T
5) Install the EMG Volume and T
5) Install the EMG Volume and Tone Controls and tighten them in.
one Controls and tighten them in.
one Controls and tighten them in.
one Controls and tighten them in.
6) Then install the pickups keeping any excess cable under the pickup
6) Then install the pickups keeping any excess cable under the pickup
6) Then install the pickups keeping any excess cable under the pickup
6) Then install the pickups keeping any excess cable under the pickup
6) Then install the pickups keeping any excess cable under the pickup
rather than in the control cavity.
rather than in the control cavity
rather than in the control cavity
rather than in the control cavity
rather than in the control cavity.
.
.
.
RED
RED
RED
GROUND
BRIDGE P/U
NECK P/U
OUTPUT
OUTPUT TO MASTER VOLUME
2 Pickups / Toggle Select Switch / Master Volume and Tone
1) Install the Pickups and route the Pickup cables to the control cavity.
If the cables are too long, wind up the excess and keep it under the pickup.
2) Mount the Volume and Tone controls into the body.
Plug both Pickup cables onto the Pickup Buss (BLACK Shroud) as shown,
Refer to diagram #6a
Bridge Pickup to position 1
Neck Pickup to position 2.
3) Plug a coax cable from the Pickup Buss (position 3) to the Master Volume
control as shown in diagram #6b.
4) Plug a coax cable from the Master Volume to the Master Tone as shown.
5) Strip the insulation from the switch wires and Insert them into the GREEN
Terminal Block and tighten the screws with a small screwdriver.
The Bridge pickup goes to the BR Terminal
The Neck pickup goes to the NK Terminal
The Output of the switch goes to the O Terminal
If there is a ground wire coming from the switch, insert it into one of the black
terminals on the terminal block.
6) Plug the output cable onto the Master Tone control and connect the output
wires to the output jack by pushing the connectors on as shown.
WHITE wire onto the TIP (T) contact,
BLACK wire onto the SLEEVE (S) contact
BLACK Battery Negative wire onto the RING (R) contact.
7) Plug the RED Wires of the pickups onto the V+ Supply Buss (RED Shroud)
along with the RED of the battery clip.
Extra pins on the V+ Supply Buss are for EMG Accessories.
8) Put the battery in the insulating foam piece provided and place it securely in the
control cavity.
We suggest that you plug in the instrument and test it before closing the
control cavity.
Diagram #6a
1) Install the Pickups and route the Pickup cables to the control cavity.
If the cables are too long, wind up the excess and keep it under the pickup.
2) Mount the Volume and Tone controls into the body.
Plug both pickup cables onto the Volume controls as shown.
Plug a coax cable from the Bridge Volume control to the Pickup Buss (Position 1)
Plug a coax cable from the Neck Volume control to the Pickup Buss (Position 2)
3) Plug a coax cable from the Pickup Buss (position 3) to the Master Tone
control as shown.
4) Strip the insulation from the switch wires and Insert them into the GREEN
Terminal Block and tighten the screws with a small screwdriver.
The Bridge pickup goes to the BR Terminal
The Neck Pickup goes to the NK Terminal
The Output of the switch goes to the O Terminal
If there is a ground wire coming from the switch, insert it into one of the black
terminals on the terminal block.
5) Plug the output cable onto the Tone control and connect the wires to the
output jack by pushing the connectors on as shown.
WHITE wire onto the TIP (T) contact,
BLACK wire onto the SLEEVE (S) contact
BLACK Battery Negative wire onto the RING (R) contact.
6) Plug the RED Wires of the pickups onto the V+ Supply Buss (RED Shroud)
along with the RED of the battery clip. Extra pins are for EMG Accessories.
7) Put the battery in the insulating foam provided and place it securely in the
control cavity.
We suggest that you plug in the instrument and test it before closing the
control cavity.
2 Pickups / Toggle Select Switch / 2 Volumes and Master Tone
Refer to Diagram #7 (Next Page)
- 9V +
Installation (Two Pickup Guitars with Selection switch):
Guitars with two pickups and a selection switch will use the EMG B157 Pickup Buss.
The Pickup Buss is a convenient way to wire your guitar without soldering.
There is a separate sheet attached to these instructions that describes the
Pickup Buss in detail.
In all installations it’s best to find a place to mount the Pickup Buss in the control
cavity before starting. Then, after the cables are routed use the velcro to mount it
securely.
H INSTRUCTIONS Page 4
OUTPUT
T
R
S
NK VOLUME
FROM NECK PICKUP
FROM BRIDGE PICKUP
BR VOLUME
BATTERY
NEG (-)
NK TONE
BR TONE
Diagram #8
2 Pickups
2 Volume (either volume will act as a master)
2 Tone
Toggle Style Switch
OUTPUT
T
R
S
NK VOLUME
FROM NECK PICKUP
FROM BRIDGE PICKUP
BR VOLUME
BATTERY
NEG (-)
MASTER
TONE
Diagram #7
2 Pickups
Toggle Style Switch
Volume each Pickup (Volumes are independent)
Master Tone
OUTPUT CABLE
RED
RED
RED
GROUND
BRIDGE P/U
NECK P/U
OUTPUT
GROUND
BRIDGE P/U
NECK P/U
OUTPUT RED
RED
RED OUTPUT CABLE
2 Pickups / Toggle Select Switch / 2 Volumes and 2 Tones)
Refer to Diagram #8
1) Install the Pickups and route the cables to the control cavity.
If the cables are too long, wind up the excess and keep it under the pickup.
2) Mount the Volume and Tone controls into the body
Plug both Neck and Bridge pickup cables onto the Volume Controls as shown.
Plug a coax cable from the Bridge (BR) Volume control to the Pickup Buss
(Position 1).
Plug a coax cable from the Neck (NK) Volume control to the Pickup Buss
(Position 2).
3) Plug a coax cable from the Bridge (BR) Volume control to the Bridge (BR) Tone
control as shown.
4) Plug a coax cable from the Neck (NK) Volume control to the Neck (NK) Tone
control as shown.
5) Strip the insulation from the switch wires and Insert them into the GREEN
Terminal Block and tighten the screws with a small screwdriver.
The Bridge pickup goes to the BR Terminal
The Neck Pickup goes to the NK Terminal
The Output of the switch goes to the O Terminal
If there is a ground wire coming from the switch, insert it into one of the black
terminals on the terminal block.
6) Plug the output cable onto the Pickup Buss (Position 3) and push the connectors
onto the jack as shown.
WHITE wire onto the TIP (T) contact,
BLACK wire onto the SLEEVE (S) contact
BLACK Battery Negative wire onto the RING (R) contact.
7) Plug the RED Wires of the pickups onto the V+ Supply Buss (RED Shroud)
along with the RED of the battery clip. Extra pins are for EMG Accessories.
8) Put the battery in the foam insulator provided and place it securely in the
control cavity.
We suggest that you plug in the instrument and test it before closing the
control cavity.
- 9V +
- 9V +

Produktspezifikationen

Marke: EMG
Kategorie: Nicht kategorisiert
Modell: 81

Brauchst du Hilfe?

Wenn Sie Hilfe mit EMG 81 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Nicht kategorisiert EMG

EMG

EMG Velociptor Racer ES106EW Bedienungsanleitung

26 August 2024
EMG

EMG Velociptor Evo ES88EW Bedienungsanleitung

21 August 2024
EMG

EMG 35DC Bedienungsanleitung

20 Juli 2024
EMG

EMG 81 Bedienungsanleitung

18 April 2024
EMG

EMG Racer Bedienungsanleitung

14 April 2024
EMG

EMG Velociptor Climb ES110OR Bedienungsanleitung

17 August 2023

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024
Ferplast

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024
AEG

AEG MECK52 Bedienungsanleitung

16 Oktober 2024
Makita

Makita UR012G Bedienungsanleitung

16 Oktober 2024
Stihl

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024
Ernesto

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024
IFM

IFM AC901S Bedienungsanleitung

16 Oktober 2024
Nedis

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024
AEG

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024
ART

ART ProChannel II Bedienungsanleitung

16 Oktober 2024