Elite ProAV Saker Tab-Tension Bedienungsanleitung

Elite ProAV Projectiescherm Saker Tab-Tension

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Elite ProAV Saker Tab-Tension (8 Seiten) in der Kategorie Projectiescherm. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
Rev.04 -D 1 2417 www.eliteproav.com
Electric Wall/Ceiling Projection Screen
Saker
Saker
Saker
SakerSaker
-
-
-
--
Tab
Tab
Tab
TabTab Te
Te
Te
TeTensio
nsio
nsio
nsionsion
n
n
nn Series
Series
Series
SeriesSeries
User’s Guide
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra
Black Top Drop in the roller. Please be aware of this as it will void your warranty with EliteProAV™.
Unapproved changes or modications (except for cutting the power cord for hardwire installations) to this
unit are prohibited and will void your warranty. For more information, please contact our Technical Support
Department at (877) 511- 1211 Ext. 604.
• Please retain this user’s guide for future reference.
• To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the
manufacturer.
• Handle the unit carefully during transportation to avoid any damages.
• To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
• The power outlet supplying power to the unit should be close to the unit and easily accessible.
• Do not install the unit on uneven or inclined surfaces.
• Do not put heavy objects on the power cord and position it properly to avoid creating a trip
obstacle.
• Never overload the power cord to prevent an electric shock or re due to a loose contact or a short
circuit.
• There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself.
No one except authorized technicians can open and make repairs to this unit.
• Make sure the power source this unit is connected to has a continuous power flow.
• If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to
avoid overheat.
• Do not handle the power plug when your hands are wet or your feet are in contact with water.
Do not use this unit under the following circumstances.
• Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.
• Avoid direct Sunshine, rain shower and moisture.
• Keep away from re sources and high temperature to prevent this device from overheating.
• Cut o the power supply rst before transportation or maintenance.
• Fully disconnect from the power supply when the unit is not in use for a long period of time, as
should be done with any other electric household appliance.
• To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is
obvious damage or if there are any evident broken parts.
Rev.04 -D 2 2417 www.eliteproav.com
WARNING
The Screen’s is already set to its maximum drop distance. There is Top Black Drop NO extra top black
drop in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modications to this product are prohibited and will void the warranty with the manufacturer.
Please contact EliteProAV™ Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rul es.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures.
 Reorient or relocate the receiving antenna of the device which may cause interference.
 Increase the separation between the screen and the device’s receiver.
 Connect the equipment into a different power outlet other than the device.
Pre- Installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign
particles such as dust, sawdust, and/or liquids.
NOTE
Regardless of the mounting method, the screen should be securely supported so that the vibration or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
that the fasteners used are of adequate strength and suitable for the installation location. Included mounting
screws are complimentary and may not be appropriate for all mounting surfaces. Use appropriate anchors to
safely secure the screen to the mounting surface or consult with a professional installer.
Hardware Parts List
Please make sure all parts listed below are included before proceeding with the installation.
A. Wall/Ceiling mount
bracket x2
B. M5x60 Screw x4
C. M -12 Dry wall
anchor x4
D.Bracket
connector x2
E. 1 M5x1 Bolt
Screw x4
F. M5x25MM round head
cross screws x2
G. M5x30MM eyebolt
screw & M5 nut x2
H. Hidden wall
bracket x2
I. R18xR6x1
washer x4
J. Snap link x2
For 135” obel w For 135”-180”
Rev.04 -D 3 2417 www.eliteproav.com
Installation Instructions
For installation assistance, please consult a professional Installer. EliteProAV™ is not liable for faulty installations.
A. Wall Mount
I.Flush mount with wall/ceiling brackets (xed position)
1. Begin (D) all the way to each end of the housing.by sliding the bracket connector
2. Then attach it to the wall/ceiling mount bracket ( (A) with the M5x11 bolt screw E).
3. Measure and mark the (WxH) distance between the two holes on each bracket.
4. Drill a hole for each screw hole on the marked areas.
5. Insert a dry- awall nchor (C) into the wall.
6. Insert aM5x60 Screw (B) in each dry-wall anchor (C) and screw it in leaving about 1/8” of an inch.
7. Hang the screen by aligning the end cap holes to the M5x60 screws ( . B)
II. Flush hidden mount (movable position)
This mount method allows the screen to slide horizontally.
1. Determine where the screen will be installed. Then, measure and mark the distance between the top and bottom
screw holes from each hidden wall mount bracket (H).
2. Drill a hole on all marked areas and brackets with the install the dry-wall anchor(C) ), M5x60 screw (B , and a
washer )(I . Make sure both brackets are properly leveled.
3. Hang the screen by placing the back over the brackets downward “catch “located on the upper “catch”.
4 . After making sure the screen is secured, you can slide it left / right to properly center it in position.
5 . Lastly, screw the M5 screw (F) into the upper hole of the bracket to add additional support for the screen.
H
Bracket connector
(D)
Wall/Ceiling Mount
Bracket (A)
M5x11 Bolt Screw
M5x60
screws (b)
Wall
Dry-wall
anchors (C)
H
W
Wall
Front view of bracket (h)
Side view of
bracket (h)

Produktspezifikationen

Marke: Elite ProAV
Kategorie: Projectiescherm
Modell: Saker Tab-Tension

Brauchst du Hilfe?

Wenn Sie Hilfe mit Elite ProAV Saker Tab-Tension benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten