Electro Harmonix MIG-50 MKII Bedienungsanleitung
Electro Harmonix
Gitarrenverstärker
MIG-50 MKII
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Electro Harmonix MIG-50 MKII (6 Seiten) in der Kategorie Gitarrenverstärker. Dieser Bedienungsanleitung war für 30 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/6
MIG-50
50W All Tube Guitar Amplifier
Congratulations on your purchase of the Electro-Harmonix MIG-50, an all tube, two
channel, 50W guitar amplifier head. The EHX MIG-50 is a faithful reissue of the
Sovtek MIG-50 with modern enhancements to both the electronics and mechnical
design. The MIG-50 comes installed with three 12AX7 preamp tubes and two 5881
power tubes.
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Clean only with a dry cloth.
Do not block any ventilation openings.
Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding-type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your
outlet consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched.
Unplug this amplifier during lightning storms or when unused for long periods of
time.
WARNING: To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
Do not expose this apparatus to dripping or splashing and ensure that no object
filled with liquids is placed on the equipment.
Maintain at least six inches of unobstructed air space behind the unit to allow for
proper ventilation and cooling. Air must be capable of freely moving around the
amplifier.
This amplifier is capable of producing very high sound pressure levels which may
cause temporary or permanent hearing damage. Use care when adjusting volume
levels during use.
Do not turn the amplifier on without a loudspeaker.
Refer all servicing and maintenance to qualified service personnel including
replacement of fuses and vacuum tubes. Changes and modifications not expressly
approved by EHX can void the warranty.
DO NOT attempt to remove the amplifier chassis. There are no serviceable parts.
DO NOT use this apparatus near water.
Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is dama r objects have ged, liquid has been spilled o
fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
The ventilation should not be impeded by covering the ventilation openings with
items, such as newspapers, tablecloths, curtains, etc.
No naked flame sources, such as ed on the lighted candles, should be plac
apparatus.
Apparatus is not for use in tropical climates.
Only use attachments/accessories specified by the manufacturer.
The appliance coupler shall remain readily operable.
The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
the product.
GETTING STARTED
BEFORE PLUGGING POWER INTO YOUR MIG-50 AMP MAKE SURE:
1. Both the POWER and STANDBY toggle switches are off, set to their DOWN
position.
2. The AC voltage marked on the rear panel matches the wall voltage for your
region or the AC voltage powering your amp.
3. The LOUDSPEAKERS output on the rear panel should be connected via a properly
rated speaker cable to a speaker cabinet with the correct impedance (a 16Ω
cabinet to the 16Ω jack or an 8Ω cabinet to the 8Ω jack, etc.). WARNING: Only
connect one speaker output at a time! Running the amp into a speaker cabinet
with mismatched impedances or with no cabinet at all could severely damage the
MIG-50 and void your warranty. Be sure to select a cabinet that can handle the
full rated 50WRMS power rating for your amp.
HOW TO POWER YOUR MIG-50 AMP:
1. Flip the STANDBY switch to the ON position first.
2. Flip the POWER switch to the ON position. The lamp should light.
3. As soon as the tubes warm up, you are ready to ROCK & ROLL!
NOTE: Contrary to popular wisdom, the STANDBY switch can actually do more harm
than good in some cases, such as is the case in the MIG-50. To increase the reliability
and longevity of your MIG-50, flip the STANDBY switch on FIRST.
FRONT PANEL
INPUT I Jack – This ¼” jack is the audio input for the normal channel. The input
impedance is 1MΩ.
INPUT II Jack – This ¼” jack is the audio input for the bright channel. The input
impedance is 1MΩ.
VOL I Knob – Controls the overall loudness of channel I, the normal channel.
VOL II Knob – Controls the overall loudness of channel II, the bright channel.
TONE Knobs – TREBLE, MIDDLE, BASS and PRESENCE controls are used to alter the
amplifier’s frequency response. Adjust to taste and experiment with different settings.
Lamp – Lights when the POWER switch is on.
Replacement part: Dial Lamp #47, T-
3-¼, 6.3V, 0.15A, bayonet base
REAR PANEL
AC INLET – Plug the standard IEC power cable into this jack.
FUSE (MAINS) – Within the AC inlet jack is the fuse holder. To access the fuse, use
a small flathead screwdriver to carefully slide the fuse holder out.
100VAC (Japan) ....................... 3A / 250V slow-blow 5x20mm fuse
117VAC (US/Canada) ............... 3A / 250V slow-blow 5x20mm fuse
230VAC (EU/Australia) ............. 1.6A / 250V slow-blow 5x20mm fuse
WARNING: The AC voltage rating is marked on the amplifier’s chassis.
Failure to use the appropriate fuse could damage the amplifier.
Produktspezifikationen
| Marke: | Electro Harmonix |
| Kategorie: | Gitarrenverstärker |
| Modell: | MIG-50 MKII |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Electro Harmonix MIG-50 MKII benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Gitarrenverstärker Electro Harmonix
8 August 2024
19 Dezember 2023
Bedienungsanleitung Gitarrenverstärker
- Gitarrenverstärker Valeton
- Gitarrenverstärker Roland
- Gitarrenverstärker Vox
- Gitarrenverstärker Yamaha
- Gitarrenverstärker Marshall
- Gitarrenverstärker Peavey
- Gitarrenverstärker Fender
- Gitarrenverstärker Behringer
- Gitarrenverstärker Boss
- Gitarrenverstärker Line 6
- Gitarrenverstärker Radial Engineering
- Gitarrenverstärker Hartke
- Gitarrenverstärker ART
- Gitarrenverstärker Orange
- Gitarrenverstärker Harley Benton
- Gitarrenverstärker Blackstar
- Gitarrenverstärker Bugera
- Gitarrenverstärker TC Electronic
- Gitarrenverstärker Palmer
- Gitarrenverstärker Ampeg
- Gitarrenverstärker Laney
- Gitarrenverstärker SPL
- Gitarrenverstärker Ashdown Engineering
- Gitarrenverstärker Suhr
- Gitarrenverstärker AER
- Gitarrenverstärker Markbass
- Gitarrenverstärker EBS
- Gitarrenverstärker Fishman
- Gitarrenverstärker Voodoo Lab
- Gitarrenverstärker GR Bass
- Gitarrenverstärker Two Notes
- Gitarrenverstärker Hughes & Kettner
- Gitarrenverstärker Dimavery
- Gitarrenverstärker AMT
- Gitarrenverstärker Budda
- Gitarrenverstärker Empress Effects
- Gitarrenverstärker DACS Audio
- Gitarrenverstärker Rivera
- Gitarrenverstärker DV Mark
Neueste Bedienungsanleitung für -Kategorien-
3 Oktober 2024
3 Oktober 2024
3 Oktober 2024
3 Oktober 2024
3 Oktober 2024
23 September 2024
19 September 2024
16 September 2024
6 September 2024
5 September 2024