Dreadbox Raindrops Bedienungsanleitung

Dreadbox Nicht kategorisiert Raindrops

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Dreadbox Raindrops (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 23 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

MODE

ON footswitch

Set the effect ON or OFF.

Also while holding the footswitch down,

it works as a SHIFT function button.

Tap footswitch

Tap tempo over the Delay Time.

When holding the TAP and the ON buttons down for 3 sec,

you will save the current Algorithm’s state.

Feedback Knob

Set the Delay’s Feedback or the Number of the repeats.

This is the main feedback control, but there are

actually 2 feedback stages:

One right after the delay line, called “Main Feedback”

& the other is located after the effects of the delay lines

(Filter and Pitch Shifter) called . “Post Feedback”

Mix Knob

Controls the Dry/Wet balance of the effect.

At 50% there is a 1:1 mix ratio.

Time Knob

Delay time from 50ms up to about 1 second.

After 700ms, the repeats will start becoming LO-FI.

NOTE: when used as a stereo output,

the R channel will have an offset compared to the L channel,

so as to achieve the stereo spread effect.

MODE Toggle Switch

This changes which parameter the Control knob affects.

For more info check on the Algorithms section (page 3).

Control knob

Depending on the algorithm and the Mode switch position,

this controls different parameters each time.

For more info check on the Algorithms section (page 3).

Output

Audio out , send to an amp,

mixer or monitor.

Input

Audio, line or fretted instrument input.

Accepts up to 2Vpp levels.

9VDC center pin negative

standard effect pedals power

Dreadbox Raindrops is a Hybrid Delay/Pitch Shifter/Reverb pedal that takes the concept of short echos

on a different level. It is equipped with multiple delay stages and different chips and you can choose

between 3 different play modes, where in each one you can have a whole new experience and alternative

soundscapes. You can achieve from simple short echos, to long, dirty and lo-fi delays and from simple

pitch shifting bursts to extensively lasting reverbs.VAT)

Main Page Controls

These are the hands on controls,

that you can access without

holding down the shift.

On/Off Indicator Delay Time Indicator

These are the SHIFT controls, that you can access while holding down the

ON button. Remember, in order to store this so that the pedal remembers

them the next time you power it, you must press and hold both footswitch-

es for 3 seconds!

TIME = EFFECT GAIN

Controls the level of the signal going into the effect’s line. By default, this

should be set at 50%, but in many cases, for example if you plug a hot

signal instrument, you might need to set this lower, so that the effects do

not peak.

FEEDBACK = POST FEEDBACK

This will control the amount of feedback that is send after the effect’s

section. For example, feedbacks after the Pitch Shifter will introduce the

shimmer effect. Be carefully though, as this feedback control and the main

one will add up and self-oscillation can be produced.

NOTE: On the reverb’s algorithm, this control is deactivated.

MIX = LOW PASS FILTER

This controls the Cut Off of a 1-pole Low Pass Filter.

CONTROL = TAP DIVISIONS

This is actually a multiplication over the tap tempo. It has fixed areas over

4 selections and it’s X1, X2, X4, X8.

MODE toggle switch

Tails ON/OFF ( ON = 2, OFF = 1). By setting this to ON, will allow the repeats

of the delay to be kept on even when the effect is set to by pass.

A. Send an Audio signal or an instrument to the input (mono signals it’s better to be send to the R INPUT)

B. Connect the Output to an Amp or a Monitor (mono signals should to be pulled out of the L OUTPUT)

C. Power the effect by using a 9VDC center pin negative power adapter (specialized for effect pedals)

D. Press the ON footswitch to enable the effect

E. Press both footswitches to change algorithms

F. To engage the secondary functions (SHIFT page) press and hold down the ON footswitch. While this is on hold, you have access to different parameters

G. In order to save the current algorithm’s settings, press and hold both footswitches for 3 seconds

MODE MODE

- CMOS Buffered Bypass

- 9VDC center pin negative

supply 150mA at least

-True stereo IN/OUT

- All IN/OUT are TS unbal-

anced 6.4mm jacks

- dimensions: 14x10x5 cm

- weight: 0,525 kg

There are 3 different algorithms offered into RAINDROPS.

1. A modulated delay

2. Pitch shifted delay

3. Large reverb

On each algorithm you can save a single preset, by holding down both footswitches for 3 seconds.

This preset will be stored and each time you power off the effect, or you cycle through the algorithms, you will have these

settings as default.

A Modulated Delay is simply the effect where the Delay Ttime is modulated by an LFO.

On this algorithm the MODE switch + CONTROL knob has the following functions:

MODE = 1 —> CONTROL = LFO RATE

MODE = 2 —> CONTROL = LFO AMOUNT

This algorithm has a Pitch Shifter as its Post Effect. The Pitch Shifter will control only the Wet signal. The Post Feedback

can have a drastic effect here, as each repeat will be shifted again.

On this algorithm the MODE switch + CONTROL knob has the following functions:

MODE = 1 —> CONTROL = PITCH (from 0 to 12 semitones - none quantised)

MODE = 2 —> CONTROL = PITCH SHIFT AMOUNT

Additionally to the Delay signal, a long tailed reverb is added .

On this algorithm the MODE switch + CONTROL knob has the following functions:

MODE = 1 —> CONTROL = REVERB DECAY

MODE = 2 —> CONTROL = REVERB MIX

Circuit: Analog signal, hybrid delay, Digital reverb

Bypass: Buffered opamp, a constant 3 to 4dB volume drop is expected and is compensated over the tremolo effect, to counter the “signal volume drop” feeling a tremolo has.