Draper SmartTrim Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Draper SmartTrim (7 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 70 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/7
If you have any difficulties installing or servicing your
SmartTrim for Barco UniSee, call your dealer or Draper, Inc.
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
© 2019 All Rights Reserved | FORM: SmartTrim_Inst19R
SmartTrim for Barco UniSee®
INSTALLATION
INSTRUCTIONS
TRIM
FLANGE
TRIM FACE
VENTED
FLANGE
MOUNTED TO WALL:
Approx. 0.25" (6.35mm)
gap between flange
and wall typical
page 2 of 7
SmartTrim for Barco UniSee
Tools Required
Important Safety Information
WARNING
Improper installation and use of SmartTrim can result in serious injury. Primarily, injuries can occur when the SmartTrim falls due to imprecise installation, mishandling of the
SmartTrim during installation or installation on an insufcient structure. Please use extreme care.
1. Please read the following installation guidelines thoroughly and follow them carefully. Failure to do so may cause product to fall or otherwise fail, and could result in serious injury.
2. Installation of SmartTrim should only be performed by an authorized, qualied, and experienced professional.
3. Do not affix the unit to walls that have inadequate strength to permanently hold the unit during use. It is the owner's and installer's responsibility to conrm the wall to which the
unit attaches is sufcient to permanently hold the weight and stress loads of the unit at all times. Draper, Inc., is not responsible for improper installation, application, testing or
workmanship related to the product at place of installation.
4. All brackets and other hardware must be installed level. Barco UniSee must be level and square.
5. Never leave the area during SmartTrim installation or maintenance unless it is secure and safe.
6. During installation or removal, carefully watch the surrounding area for any potential safety concerns including nearby persons or objects.
7. Installation of SmartTrim should be performed only by authorized and qualified personnel, who have been trained in the safe and effective installation of the SmartTrim &
understand its safety features.
8. SmartTrim may need to comply with local, state or district rules and regulations, in particular when installed in schools.
All applicable rules and regulations should be reviewed before installation and use.
9. Failure to precisely follow installation guidelines invalidates all warranties.
10. Custom products
/
installations may not be reflected in this manual. Call Draper, Inc., if you have questions about custom products or any questions about your installation.
Before Beginning Installation
1. Look for any job site conditions that could interfere with installation of the system.
2. Read carefully and be sure to understand all installation instructions and all related operations manuals. These instructions are intended to as a guide for the installer and owner.
They should be followed closely and combined with the expertise of experienced qualied installers. Draper, Inc., is not responsible for improper installation, application, testing
or workmanship related to the product at place of installation. Please retain all instructions for future use.
3. Open cartons lengthwise.
4. Locate and lay out all pieces.
5. Inspect all boxes to make sure you have received the proper SmartTrim parts.
6. If you have any difculties with installing or servicing your SmartTrim, call your dealer or Draper, Inc., 765 987-7999.
No. 5 HEX WRENCH
Barco Unisee
Service Tool
OR
Section 1 - SmartTrim List of Parts
Standard Parts for all installations For installations larger than 2 x 2
Section 2 - SmartTrim Panel Map
Caution: UniSee LCD Display wall must be properly assembled, aligned on all axes and level.
page 3 of 7
SmartTrim
for Barco UniSee
®
C C 2 8 7 . 0 4 2 S A
C C 2 8 7 . 0 4 3 S AC C 2 8 7 . 0 4 4 S A
C C 2 8 7 . 0 3 8 S AC C 2 8 7 . 0 3 7 S A
C C 2 8 7 . 0 3 9 S A C C 2 8 7 . 0 4 0 S A C C 2 8 7 . 0 4 1 S A
C C 2 8 7 . 0 3 9 S A C C 2 8 7 . 0 4 0 S A C C 2 8 7 . 0 4 1 S A
C C 2 8 7 . 0 3 6 S A
Corner
Vertical
Trim B - (2x)
CC287.039SA
Corner
Vertical
Trim A - (2x)
CC287.041SA
Top Left Trim - (1x)
CC287.036SA
Top Right Trim - (1x)
CC287.038SA
Bracket Washers - (12x)
Bracket Fasteners [M6x20] - (12x)
Top Horizontal Trim - (varies)
CC287.037SA
Bottom Left Trim - (1x)
CC287.044SA
Bottom Right Trim - (1x)
CC287.042SA
Bottom Horizontal Trim - (varies)
CC287.043SA
Corner Trim Brackets -
(4x)
C002.1552SA
Corner Trim Brackets -
(4x)
C002.1553SA Middle
Vertical
Trim - (varies)
CC287.040SA
Edge Trim Brackets -
(varies)
C002.1554SA
Bracket
Alignment
Tool -
(1x)
C002.1555SA
Figure 1


Produktspezifikationen

Marke: Draper
Kategorie: Nicht kategorisiert
Modell: SmartTrim

Brauchst du Hilfe?

Wenn Sie Hilfe mit Draper SmartTrim benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Draper

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-