DPW Design Limit Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für DPW Design Limit (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Limit L-2, Triple Limiter
The L-2 is a three individual soft knee limiter module in Eurorack format. An all analog unit.
It can be used for audio signal manipulation or as a utility module for control voltages. The three
channels can be AC or DC coupled.
It can be used for normal limiting/compression but also for creative wave shaping.
Compared to the previous L-1 module the only change is added noramling between the channels.
The soft knee of the limiter is actually 8 consecutive soft knees for each channel starting at -6dB
compared to 5V and spread evenly up to 5V.
The limiter will brick wall limit to +/- 5V both in AC and DC mode.
In other words it gradually increase the compression from +8dBu and brick wall limits at +14dBu.
Controls
For each channel there is a volume control that sets how hard the limiter
is driven.
When the knob is at 9 o'clock what passes through is almost unaffected only
compressing high peaks. Turning the the knob to full on will give 5 times
amplification drive in to the limiter, giving a rounded distorted sound.
The three channels are completely independent.
AC/DC coupling for Lim1 and Lim2 is done with the switch on the panel.
AC/DC coupling for Lim3 is done by a jumper on the back of the module.
When the jumper is mounted Lim3 is DC coupled.
The module is delivered with the jumper mounted.
If you want higher compression than just one limiter you can chain
several limiters, this is pre-patched via normaling.
If nothing is connected to IN on channel 2 or 3 they will get their input
from the channel above as shown by the dotted lines on the front
panel. This is also so you easily can get tree different compressed
versions of the same sound out.
Connecting something in on 2 or 3 will disconnect the noramling.
Device specs
Module size: 6 hp wide, 32 mm deep with power connector.
Input impedance: 20 kohm
Output impedance: 1 kohm
Power requirements: +/- 12V. Max power consumption +/- 20 mA
Connect the power cable with the red stripe (-12V) down.
The unit is protected for reverse power.
DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden
www.dpw.se MAN-L-2 Rev B
Use case examples
A few examples, just to get your imagination going.
Normal limiting/compression
As there are three limiters two of them can for instance be used for a stereo drum bus and you still have one
more for an additional effect.
The limiter can be used to add more weight to sounds like for instance a kick. Or a way to bring out the tails
of plucky sounds by compressing the transients and amplifying the rest of the sound. Another useful case is
to compress thin sounding sounds so they sit better in a mix with analog synths.
The L-2 is also very handy to have in feedback patches.
Level protection
If you set the L-2 low you will not be able to hear the effect of the compression, it will sound
transparent but will never allow peaks above +/-5V. This can be a way to protect your sound
card or the front of house mixer from high peaks if you are playing in a club.
Waveshaping AC mode
Can be used in AC mode to drive signals to shape it through the limiter. Mild settings will add a bit of
harmonics and hard drive will add a mild distortion. Try it on sine waves to get some pleasant harmonics and
make the sine cut a bit better through the mix.
Also try mixing different waves going into the L-2 and compressing
them together.
As the chanels are normalled in series you could have three
different versions of compressed signals out with just one signal in.
This can be used for variantions of your sound by connecting a
switch for selection of output.
Waveshaping DC mode
As above for AC mode but for LFOs, envelopes or other slowly changing signals.
By mixing several LFOs you can get a result higher that +/-5V. The L-2 can be used in DC mode to
guarantee that the result never will be above +/- 5V.
Can also be useful if you use envelopes that are +8V as control voltages and you want them to be max 5V.
PWM of any signal
Set the L-2 to DC mode. If you offset your audio signal with a voltage you can drive the signal harder in to
one side of the limiter to give an asymmetric wave.
This can be done by connecting an AV-1 before the L-2, using
channel A for audio and the B knob for voltage offset. SUM
connects to the input of L-2.
You don't have to use an AV-1. Any DC coupled mixer will do.
If you connect an LFO to the B input of the AV-1 then the LFO will
carry the audio and drive it harder in to the positive and negative
limits of the L-2. This will give the possibility to do some kind of
PWM of sine waves or any other signal.
You can as shown in the picture like in the waveshaping example get different versions of this PWM like
signal out if you don't connect anything in on channel 2 and 3.
Please check www.dpw.se for updates of the manual and demo videos.
DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden
www.dpw.se MAN-L-2 Rev B


Produktspezifikationen

Marke: DPW Design
Kategorie: Nicht kategorisiert
Modell: Limit

Brauchst du Hilfe?

Wenn Sie Hilfe mit DPW Design Limit benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert DPW Design

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-