Doepfer A-136 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Doepfer A-136 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
doepfer System A - 100 Distortion / Waveshaper A-136
1
1. Introduction
Module A-136 is a distortion and waveshaping mo-
dule with extensive control possibilities. Different set-
tings of 5 distortion/waveshaping parameters enable a
lot of very complex and extreme waveform modificati-
ons.
The incoming audio or cv signal is divided into 3
sections: original, positive and negative component.
For the positive and negative component, clipping
levels (L) are defined. Only voltages beyond this level
effect the output signal. For each of the three sections
the positive or negative amplification (A) can be adju-
sted.
External control voltages can be used to alter both
clipping levels so that dynamic waveform changes are
possible.
The range of modification goes from simple soft or hard
clipping to completely altered waveforms where the
original signal is no longer recognizable.
Typical applications are audio distortion, and waveform
modification for audio signals as well as for control
voltages (LFO, ADSR, random etc.).
Output
+ A
Input
A-136
DIS
A
- A
+ L
- L
Ext. Level
Ext. Level
A-136 Distortion / Waveshaper System A - 100 doepfer
2
2. DIS - Overview Controls:
1 A : Amplification control for original signal
2 + L : Clipping control for positive signal compo-
nent
3 - L : Clipping control for negative signal com-
ponent
4 + A : Amplification control for positive signal
component (above the positive clipping
level)
5 - A : Amplification control for negative signal
component (below the negative clipping
level)
In / Outputs:
! Input : Signal input
" Ext. Level : ext. CV input for positive clipping level
§ Ext. Level : ext. CV input for negative clipping le-
vel
$ Output : Signal output
A-136
DIS
Ext. Level
Input
+ A
Distortion / Waveshaper
010
010
0 10
010
0 10
Output
Ext. Level
+ L
A
- L
- A
+A
-A
+L
-L
A
doepfer System A - 100 Distortion / Waveshaper A-136
3
3. Controls
1 A
Control 1 defines the amplification A of the original
signal. The range of the amplification factor is about
-4...+4. This means that one can obtain actual
amplification (range +1...+4), or attenuation (range
0...+1) or even inversion of the original signal (range
-4...0). The table below shows the approximate
assignment of some control settings and the
corresponding amplification factors:
Tab. 1: How control settings affect amplification
factors
2 + L • 3 - L
Controls 2 and 3 adjust the positive (+L) and
negative (-L) respectively.clipping levels
In the positive signal section only signal voltages
above the positive clipping level +L are affected by the
amplification control +A.
In the negative signal section only signal voltages
below the negative clipping level -L are affected by the
amplification control -A.
Fig. 1: how the clipping levels work (input signal =
triangle)
Control
setting
Amplification
factor Explanation
0 about -4 maximum negative amplification
3,5 about -1 same amplitude as input signal but
inverted
5 about 0 suppression of input signal
6,5 about 1 same amplitude as input signal
10 about 4 maximum positive amplification
0
+ L
- L


Produktspezifikationen

Marke: Doepfer
Kategorie: Nicht kategorisiert
Modell: A-136

Brauchst du Hilfe?

Wenn Sie Hilfe mit Doepfer A-136 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Doepfer

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-