Doepfer A-101-2 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Doepfer A-101-2 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
doepfer System A - 100 Vactrol Lowpass Gate A-101-2
1
1. Introduction Module A-101-2 is a vactrol based combination of
Low Pass filter (LP) and VCA. Additionally a combined
mode LP+VCA is available. In this mode the sound
becomes more dull as the loudness decreases.
The A-101-2 was inspired by module 292 of Don Buchla.
He also intruduced the term "Low Pass Gate" for this
combination of functions.
The function of the module is controlled by a manual
switch or by two gate inputs.
In principle the A-101-2 is a 12 dB low pass that can be
switched to VCA or a combination of Low Pass and
VCA. The controlling elements for frequency resp. loud-
ness are so-called vactrols. A vactrol is a combination
of a light depending resistor (LDR) and a light emit-
ting diode (LED) both put into a small light-proof case.
Vactrol based circuits are known for their soft low-
distortion sound. For details about vactrols please use
the corresponding link in the A-101-2 info page on our
web site www.doepfer.com.
Frequency resp. loudness is controlled manually and
by two control inputs.
The audio input is very sensitive in filter mode to obtain
distortion effects if desired.
The resonance function "colors" to the sound and is
adjustable all the way up to self-oscillation.
In contrast to the Buchla design the A-101-2 offers the
resonance feature, attenuators for both CV and audio
input, and two gate inputs to control the function of the
module in addition to the manual toggle switch.
A-101-2 Vactrol Lowpass Gate System A - 100 doepfer
2
Controls:
1 F/A manual frequency/loudness control
2 CV2 attenuator for CV input "
3 Level attenuator for audio input §
4 Resonance resonance control
5 Function function toggel LP / LP+VCA / VCA
6LED control for frequency/loudness
Inputs / Outputs:
! CV In 1 frequency/loudness CV input 1
" CV In 2 frequency/loudness CV input 2
§ Audio In audio input
$ Audio Out audio output
%a G1 function control input 1 (gate 1)
%b G2 function control input 2 (gate 2)
2. Overview
1!
"
§
$
2
3
4
5
%a
%b
6
doepfer System A - 100 Vactrol Lowpass Gate A-101-2
3
3. Controls / Inputs / Outputs
1 F/A (control) / ! CV In 1 (socket)
2 CV2 (control) / " CV In 2 (socket)
This group of elements is responsible for the filter fre-
quency resp. loudness (audio level / amplitude) accor-
ding to the selected function. Control 1 F/A is used to
adjust the frequency resp. loudness manually. The con-
trol voltage inputs ! CV In 1 and " CV In 2 enable
voltage control of the frequency resp. loudness by
means of external voltages (e.g. ADSR, LFO, random
voltage, S&H). The input is equipped with the" CV In 2
attenuator 2 CV2. Input ! CV In 1 has no attenuator
available.
Remark: Module A-101-2 uses so-called vactrols to
control frequency and resp. loudness. The light depen-
ding resistors inside the vactrols show a considerable
slowness of the resistance variation. Consequently fre-
quency resp. loudness changes are not as fast as for
other A-100 filters or VCAs that do not use vactrols. Fast
attacks or decays (CV = ADSR) or FM effects in audio
range (CV = LFO or VCO) are not possible with vactrol
based circuits. Please use one of the other A-100 filters
or VCAs for these purposes. By means of a LFO with
gradually increasing frequency one can discover the
maximum modulation frequency that the vactrols are
able to follow.
The LED near the frequency control 1 is a rough
measure of the current frequency resp. loudness. This
LED is connected in series with the LEDs inside the
vactrols and consequently shows the current illumination
inside the vactrols.
Due to the"crooked" response of vactrols the filter has
not an exact control standard (like V/Oct or dB/V). The
inevitable tolerances and tracking errors between diffe-
rent vactrols will also lead to an individual sound of each
module and individual frequency and resonance beha-
viour.
3 Level (control) / § Audio In (socket)
This is the audio input of the module with the correspon-
ding level control (attenuator). At socket § the audio
signal to be processed by the module is fed in (e.g. VCO
output).
The audio input is very sensitive in the low pass mode so
that even distorted sounds can be obtained - especially
for higher resonance settings. From about middle posi-
tion ( ~ 5) distortion appears with A-100 standard audio
signals (e.g. VCO output). Even in the VCA and combi-
ned LP+VCA mode distortions are possible. But they are
distinctly smaller than in low pass mode.


Produktspezifikationen

Marke: Doepfer
Kategorie: Nicht kategorisiert
Modell: A-101-2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Doepfer A-101-2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Doepfer

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-