Dimplex CFS60 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Dimplex CFS60 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
08/19440/1 (UK) Issue 1
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility
(EMC) EN55014, EN60555-2 and EN60555-3 which cover the essential requirements of EEC Directives 73/23 and 89/336
Switch Panel
CFCS
2
CFS30
1
3
5
4
7
6
CFS30
CFS60
CFS90
CFS120
SPC
123
T
I
0
D
N L1 L2 L3
380 - 415V
3PN + E
T
C
M
A B
1L1 3L2 5L3 13NO A1
A214NO6T34T22T1 2T1 4T2 6T3 14NO A2
A113NO5L33L21L1
N L F H1 H2
E
D
230-240V ~1PN
T
E L1 F H1 H2E N L
C
M
E
CFS60
CFS90
CFS120
CFS60
CFS90
CFS120
134mm
75mm
48mm
85mm
145mm
120mm
‘1’
‘2’
‘3’
c
d
'y'
b
a
y
2
3
x
1
a
b
d
c
Dimplex Industrial Fan Heater
Switch Panel : CFCS
Important Safety Advice
Always disconnect the supply before working on
the product.
This product should be mounted safely onto a
suitable wall.
Ensure that cables are of adequate current carrying
capacity.
The Switch Panel should not be installed in a toilet
or washroom.
WARNING: Isolate electrical supply to ALL modular
linked units when carrying out maintenance.
Electrical
The installation of this appliance should be carried out by a
competent electrician and be in accordance with the current
IEE wiring regulations.
Installation
The backing box should be fixed to a suitable wall with
appropriate conduit used where applicable to carry the cable
between the heater and the switch panel. (see Fig. 3 for
dimensions)
This cable used to connect the heater to the switch panel
should have sufficient cores (typically 5 core) to allow
connection as per the enclosed wiring diagram and be at
least 1.0mm².
Test all switch settings once installation is complete.
Connections – To the Switch Panel
Connection are made as shown in Fig. 4. (References listed
below).
1 - FAN ON - OFF
2 - HEAT 1
3 - HEAT 2
T - TERMINAL BLOCK
SPC - SWITCH PANEL CABLE TO HEATER (NOT
SUPPLIED)
Tip: When stripping back the switch panel cable make note
of the numbering or colours of each wire and their
associated connections to the terminal block.
Connections – To the Heater
Note: Suitable conduit should be used to run switch panel
cable to heater.
- Control connections to the CFS30 model is achieved by
detaching the control housing (‘y’ in Fig. 5) by removing the
two screws and hinging the housing as shown. Then remove
a knock-out from the back panel of the heater and using 5
core cable (see ‘b’ in Fig. 5) make the control connections
to terminal block ‘d’ also shown in Fig. 5.
- Control connections to the CFS60, CFS90 & CFS120
models are achieved by detaching the control housing (‘y’
in Fig. 6) by turning the two quarter turn screws and hinging
the housing as shown (see step 1 in Fig. 6). The bottom
panel (‘x’ in Fig. 6) is detached by removing two screws and
lifting off as shown (see steps 2 & 3 in Fig. 6). Then remove
one of the smaller knock-outs and using 5 core cable (see
‘b’ in Fig. 7) make the control connections to terminal block
‘d’ also shown in Fig. 7.
On completion of control connections, fix the switch panel
cable in the back panel using a suitable cable gland (not
supplied) and replace the control housing and bottom panel.
Switch on power to heater and ensure that all switch settings
are functioning correctly.
Operation of switch panel
Switch on electrical supply (MAINS IN) to the heater. Switching
the switch marked ‘I’ energises the fan and for CFS30 model
switches on the electrical supply to the heater. The heat
selection switches allow heat settings to be chosen as shown
below:
Settings - I Fan Only
I + Half Heat
I + Full Heat
The desired heater setting can be obtained through switch
selection.
Recycling
For electrical products sold within the
European Community.
At the end of the electrical products useful life
it should not be disposed of with household
waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for
recycling advice in your country.
Cleaning
WARNING: DISCONNECT SUPPLY before carrying out
maintenance.
External appearance can be maintained by wiping
occasionally with a damp cloth ; for stain removal, a weak
soap solution can be applied with a cloth and the surface
wiped dry. Care must be taken to avoid any moisture ingress
into the product.
After Sales Service
Your product is guaranteed for one year from the date of
purchase.
Within this period, we undertake to repair or exchange this
product free of charge provided it has been installed and
operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales service you should contact
our customer services help desk on 0870 727 0101. It would
assist us if you can quote the model number, series, date of
purchase, and nature of the fault at the time of your call. The
customer services help desk will also be able to advise you
should you need to purchase any spares.
Please do not return a faulty product to us in the first instance
as this may result in loss or damage and delay in providing
you with a satisfactory service.
Please retain your receipt as proof of purchase.
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE


Produktspezifikationen

Marke: Dimplex
Kategorie: Nicht kategorisiert
Modell: CFS60

Brauchst du Hilfe?

Wenn Sie Hilfe mit Dimplex CFS60 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Dimplex

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-