Digital Yacht ANT200 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Digital Yacht ANT200 (2 Seiten) in der Kategorie Marine. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
QUICK START AIS400-01-VR1
Installation & Quick Start Guide
ANT200 AIS Receiver
1. Introduction
Congratulations on the purchase of your ANT200 AIS Receiver. It is recommended that your receiver is installed by a
professional installer. You will need to purchase a suitable 1” x 14 TPI thread mounting bracket for the ANT200.
Before operating the unit you should also familiarise yourself again with the user manual of the chart
plotter that you are connecting the ANT200 to. Pay particular attention to the AIS section and any settings
that need to be configured for correct operation.
2. Before you start
The ANT200 is a smart “all in one” AIS receiver solution for small boats. Simply connect the ANT200 to a 12v or 24v DC
supply and it will immediately start receiving AIS target data and outputting this data in high speed NMEA 0183 format
(38,400 baud).
In some installations, it maybe desirable to connect low speed NMEA 0183 (4800 baud) GPS data to the ANT200 and for
the ANT200 to merge (multiplex) the AIS data with the GPS data and send everything at 38,400 baud to a dedicated
chart plotter or PC with just one serial port.
Carefully consider how you wish to connect the ANT200 to your existing navigation system before you start installing
cables. To display the AIS targets and data you will need:
Suitable dedicated chart plotter that can read and display AIS data via NMEA0183
Or a suitable PC Navigation software running on a PC with Microsoft Windows XP®/Windows 2000® or Windows
Vista®/Windows 7® with a free RS232 serial port or a free USB port and USB to serial port adaptor.
www.busse-yachtshop.de | info@busse-yachtshop.de
DIGITAL YACHT LTD
ANT200 Quick Start Guide
3. Installation
Before starting installation select a suitable location for the ANT200 AIS Receiver. The unit is water proof and designed
for on-deck mounting. The ANT200 antenna has the popular 1” x 14 TPI thread mount, found in many VHF antennas. A
wide variety of different brackets are available for this type of threaded mount, consult your local marine electronics
dealer or chandlery for more information.
The 1” x 14 TPI thread mount can also be removed, allowing the ANT200 to be flush mounted on a flat horizontal surface.
The ANT200 is supplied with 15m of cable and this should be routed through the vessel to a suitable dry internal location
where it can be connected to the boat’s DC power system and the equipment it will be interfaced with. The cable can be
shortened, lengthened or joined without problems.
The ANT200 should be connected to the boat’s DC supply via a 1 Amp fuse. The unit requires 9.6V to 28.8V supply
voltage.
Below are the wiring details for the ANT200 and a connection diagram that shows how to interface it to other navigational
equipment.
Wiring Colours;
Red
Power + (12v or 24v)
Black
Power (0v)
Grey
NMEA Out + (AIS+GPS data)@38400
Brown
NMEA Out -
Yellow
NMEA In+ (GPS data)@4800
Green
NMEA In-
Connection Diagram;
NOTE: Connection of the GPS Unit to the ANT200 is not mandatory but can be useful in
some installations where the dedicated chart plotter only has one NMEA Input port
www.busse-yachtshop.de | info@busse-yachtshop.de


Produktspezifikationen

Marke: Digital Yacht
Kategorie: Marine
Modell: ANT200

Brauchst du Hilfe?

Wenn Sie Hilfe mit Digital Yacht ANT200 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Marine Digital Yacht

Bedienungsanleitung Marine

Neueste Bedienungsanleitung für -Kategorien-