DeWalt D25213K Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für DeWalt D25213K (7 Seiten) in der Kategorie bohren. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/7
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286
(JUL09) Part No. N018731 Copyright © 2006, 2009 DEWALT
D25113, D25213, D25313, D25223, D25323, D25324, D25330
The following are trademarks for one or more DEWALT power tools: the yellow and black
color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box
configuration; and the array of lozenge-shaped humps on the surface of the tool.
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-DÔWALT • www.dewalt.com
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not avoided, result will
in death or serious injury.
WARNING: could Indicates a potentially hazardous situation which, if not avoided,
result in death or serious injury.
CAUTION: may Indicates a potentially hazardous situation which, if not avoided, result
in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation
which, if not avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)
WARNING: To reduce the risk of injury, read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or
a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-
related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power
tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with these
instructions taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could result
in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Additional Safety Instructions for Rotary Hammers
• Wear ear protectors. Exposure to noise can cause hearing loss.
• Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.
• Hold power tools by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact with a “live”
wire will make exposed metal parts of the tool “live” and shock the operator.
• Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss of
control.
• Wear safety goggles or other eye protection. Hammering operations cause chips to
fly. Flying particles can cause permanent eye damage. Wear a dust mask or respirator for
applications that generate dust. Ear protection may be required for most applications.
• Keep a firm grip on the tool at all times. Do not attempt to operate this tool without
holding it with both hands. It is recommended that the side handle be used at all times.
Operating this tool with one hand will result in loss of control. Breaking through or encountering
hard materials such as re-bar may be hazardous as well. Tighten the side handle securely
before use.
• Do not use this tool to mix or pump easily combustible or explosive fluids (benzine, alcohol,
etc.).
• Do not mix or stir inflammable liquids labelled accordingly.
• Do not operate this tool for long periods of time. Vibration caused by hammer action may
be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure
by taking frequent rest periods.
• Do not recondition bits yourself. Chisel reconditioning should be done by an authorized
specialist. Improperly reconditioned chisels could cause injury.
• Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and
bits may get extremely hot during operation. Small bits of broken material may damage bare
hands.
• Never lay the tool down until the bit has come to a complete stop. Moving bits could
cause injury.
• Do not strike jammed bits with a hammer to dislodge them. Fragments of metal or
material chips could dislodge and cause injury.
• Slightly worn chisels can be resharpened by grinding.
• Keep the power cord away from the rotating bit. Do not wrap the cord around any part
of your body. An electric cord wrapped around a spinning bit may cause personal injury and
loss of control.
• Air vents often cover moving parts and should be avoided. Loose clothes, jewellery or
long hair can be caught in moving parts.
• An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that
is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. When using more than one extension to
make up the total length, be sure each individual extension contains at least the minimum
wire size. The following table shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge
number, the heavier the cord.
Minimum Gauge for Cord Sets
Ampere Rating
Volts Total Length of Cord in Feet (meters)
120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
More
Than
Not More
Than
AWG
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
NOTE: Do not overheat the bit (discoloration) while grinding a new edge. Badly worn chisels
require reforging. Do not reharden and temper the chisel.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also
use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially designed to filter out microscopic
particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.
WARNING: Always use eye protection. All users and bystanders must wear eye protection
that conforms to ANSI Z87.1.
WARNING: Always wear proper personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
may contribute to hearing loss.
• The label on your tool may include the following symbols. The symbols and their definitions
are as follows:
V ........................ volts A .......................amperes
Hz ...................... hertz W ......................watts
min ....................minutes .................... alternating current
.................direct current .................... alternating or direct current
......................Class I Construction no ..................... no load speed
.......................... (grounded) ..................... earthing terminal
......................Class II Construction ..................... safety alert symbol
.......................... (double insulated) BPM ................. beats per minute
…/min ...............per minute RPM ................. revolutions per minute
Motor
Your DEWALT tool is powered by a D WALT-built motor. Be sure your power supply agrees E
with the nameplate markings. Voltage decrease of more than 10% will cause loss of power and
overheating. All DEWALT tools are factory tested.
COMPONENTS (Fig. 1)
WARNING: Never modify the power tool or any part of it. Damage or personal injury could
result.
A. Variable speed switch F. Chuck
B. Active vibration handle G. Dust cover
(D25223, D25323, D25324 only) H. Depth adjustment rod
C. Forward/reverse slider (D25113, D25213, I. Side handle
D25313, D25223, D25323, D25324) J. Depth stop button
D. Mode selector (D25113, D25213, K. Locking collar (D25324 only)
D25313, D25223, D25323, D25324) L. Lock-on button (D25113, D25330 only)
E. Mode selector button (D25113, D25213, M. Chisel rotation (D25330 only)
D25313, D25223, D25323, D25324)
D25113, D25213, D25313, D25223, D25323, D25324 Heavy-Duty 1" (26 mm) SDS Plus ® Rotary Hammers
D25330 Heavy-Duty SDS Plus® Chipping Hammer
Marteaux rotatifs industriels SDS Plus®, 26 mm (1 po), D25113, D25213, D25313, D25223, D25323, D25324
Marteau burineur industriel SDS Plus® D25330
Rotomartillos SDS Plus® de 26 mm (1") para trabajos pesados D25113, D25213, D25313, D25223,
D25323, D25324 Martillo de soldador SDS Plus® para trabajos pesados D25330
INTENDED USE
These heavy-duty rotary hammers have been designed for professional drilling and hammerdrilling,
screwdriving and light chipping at various work sites (i.e., construction sites). DO NOT use under
wet conditions or in presence of flammable liquids or gases.
These heavy-duty rotary hammers are professional power tools. DO NOT let children come into
contact with the tool. Supervision is required when inexperienced operators use this tool.
Active Vibration Control (Fig. 1)
D25223, D25323 AND D25324 ONLY
The active vibration control reduces rebound vibration from the hammer mechanism. Reducing
hand and arm vibration allows for more comfortable use for longer periods of time and extends
the life ofthe unit.
For best vibration control, hold the tool with one hand on the main handle (B) and the other hand
on the side handle (I). Apply just enough pressure so the hammer is approximately mid-stroke.
The hammer only needs enough pressure to engage the active vibration control. Applying too
much pressure will not make the tool drill or chip faster and active vibration control will not
engage.
Torque Limiting Clutch
All rotary hammer drills are equipped with a torque limiting clutch that reduces the maximum
torque reaction transmitted to the operator in case of jamming of a drill bit. This feature
also prevents the gearing and electric motor from stalling. The torque limiting clutch has been
factory-set and cannot be adjusted.
Side Handle (Fig. 2)
WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side
handle properly installed and securely tightened. Failure to do so may result in the side handle
slipping during tool operation and subsequent loss of control. Hold tool with both hands to
maximize control.
A side handle comes assembled with this rotary hammer. The side handle (I) can be fitted to suit
both right-hand and left-hand users.
TO ADJUST THE SIDE HANDLE
1. Loosen the side handle (I) by turning it counterclockwise.
2. Rotate the side handle to the desired position.
3. Tighten the side handle by turning it clockwise.
TO CHANGE SIDES
For right-hand users: slide the side handle clamp over the chuck, handle at the left.
For left-hand users: slide the side handle clamp over the chuck, handle at the right.
Trigger Switch (Fig. 1)
To start the rotary hammer, depress the trigger switch (A). To stop rotary hammer, release the
switch.
NOTE: Use lower speeds for starting holes without a centerpunch, drilling in metal, plastics
or ceramics, or driving screws. Higher speeds are better for drilling in masonry for maximum
efficiency.
VARIABLE SPEED
The variable speed trigger switch (A) permits speed control. The farther the trigger switch is
depressed, the higher the speed of the drill.
D25113, D25213, D25313, D25223, D25323, D25324
To lock the tool in Off position move the forward/reverse slider (C) to the central position.
Lock-on Button (Fig. 1)
D25113, D25330
WARNING: Be sure to release the locking mechanism before disconnecting the plug from the
power supply. Failure to do so will cause the hammerdrill to start immediately the next time it is
plugged in. Damage or personal injury could result.
The lock-on button (L) is for use only when the rotary hammer is stationary, mounted in a drill
press stand or for chipping applications.
Before using the tool each time, be sure that the lock-on button release mechanism is working
freely.
D25113 ONLY
To lock the trigger switch in the on position for continuous operation, depress and hold the trigger
switch and slide the lock-off button (L) forward. The tool will continue to run.
To turn the tool off from a locked on condition, squeeze the trigger once then release it.
D25330 ONLY
To lock the trigger switch in the On position for continuous operation, depress the trigger switch
and push the lock-on button (L) in. The tool will continue to run.
To turn the tool Off from a locked on condition, squeeze the trigger once then release it.
Forward/reverse Slider (Fig. 1)
D25113, D25213, D25313, D25223, D25323, D25324
WARNING: Always wait until the motor has come to a complete standstill before changing the
direction of rotation.
CAUTION: When reversing to clear jammed bits, be ready for strong reactive torque.
The forward/reverse slider (C) is used to reverse the rotary hammer for backing out fasteners or
jammed bits mode.
1. Push the forward/reverse slider (C) to the left (viewed when holding drill in operating position)
for forward (right-hand) rotation. See arrows on tool.
2. Push the forward/reverse slider (C) to the right for reverse (left-hand) rotation.
Mode Selector (Fig. 3)
D25113, D25213, D25313, D25223, D25323, D25324
NOTICE: Tool must come to a complete stop before activating the mode selector button or
damage to the tool may result.
DRILL-ONLY MODE
To use drill-only mode, press mode selector button (E) and turn the mode selector (D) so the
yellow arrow points to the corresponding symbol as shown. Use drill-only mode for wood, metal,
and plastics.
HAMMERDRILL MODE
To use hammerdrill mode, press the mode selector button (E) and turn the mode selector (D)
so the yellow arrow points to the corresponding symbol as shown. Use this mode for masonry
drilling.
HAMMER-ONLY MODE
For light chiseling, press the mode selector button (E) and turn the mode selector (D) so the
yellow arrow points to the corresponding symbol as shown.
NOTE: The yellow arrow on the mode selector MUST be aligned with the one of the symbols
at all times. There are no operable positions between the positions.
CHISEL ROTATION
D25313, D25323, D25324
To manually rotate the chisel, depress the button (E) and turn the mode selector (D) so the yellow
arrow points to the corresponding symbol as shown.
SDS Plus® Chuck (Fig. 1)
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool
from power source before making any adjustments or removing/installing attachments or
accessories.
WARNING: Burn Hazard. ALWAYS wear gloves when changing bits. Accessible metal parts
on the tool and bits may get extremely hot during operation. Small bits of broken material may
damage bare hands.
WARNING: Do not attempt to tighten or loosen drill bits (or any other accessory) by gripping
the front part of the chuck and turning the tool on. Damage to the chuck and personal injury
may occur.
To insert bit, insert shank of bit about 3/4" (19 mm), no further than 7/8" (22 mm) into chuck.
Push and rotate bit until it locks in place. The bit will be securely held.
To release bit, pull the chuck sleeve (F) back and remove the bit.
OPERATION
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool
from power source before making any adjustments or removing/installing attachments or
accessories.
WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is anchored
or clamped firmly. If drilling thin material, use a wood “back-up” block to prevent damage to the
material.
To reduce the risk of personal injury, ALWAYS operate the tool with the side handle
properly installed and securely tightened. Failure to do so may result in the side handle
slipping during tool operation and subsequent loss of control. Hold tool with both hands to
maximize control.
Proper Hand Position (Fig. 3)
WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position
as shown.
WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation
of a sudden reaction.
Proper hand position requires one hand on the side handle (I), with the other hand on the main
handle (B).
Overload Clutch
If the drill bit becomes jammed or caught, the drive to the drill spindle is interrupted by the
overload clutch. Because of the forces that occur as a result, always hold the machine securely
with both hands and take a firm stance.
Drilling Tools
The machine is intended for hammerdrilling in concrete, brick and stone. It is also suitable for
drilling without impact in wood, metal, ceramic and plastic.
FIG. 3
FIG. 4
J
H
I
FIG. 1
K
D25324
I
FIG. 2 FIG. 3
DRILL-ONLY MODE
MODE PERÇAGE SEULEMENT
MODO SÓLO TALADRO
HAMMER/DRILL MODE
MODE PERFORATION-PERÇAGE
MODO TALADRO/PERCUTOR
CHISEL ROTATION
ROTATION DU BURIN
ROTACIÓN DE CINCELES
(D25313, D25323, D25324 ONLY)
HAMMER-ONLY MODE
MODE PERFORATION SEULEMENT
MODO SÓLO MARTILLO
E
E
E
D25113
C
A
I
H
F
D
L
D25330
A
L
M
I
Chipping Tools
The machine is intended for chipping in concrete, brick and stone.
Removable SDS Plus® Chuck and Three Jaw Keyless
Chuck (Fig. 1)
D25324
The D25324 is equipped with a removable quick change SDS Plus®
chuck as well as a removable
three jaw keyless chuck. The hammer mechanism does not function when the three jaw keyless
chuck is used.
Both the SDS Plus® and three jaw keyless chuck can be easily removed by turning the locking
collar (K) into the unlocked position to release the chuck.
The SDS Plus®
and three jaw keyless chuck can be easily attached by inserting the chuck into the
spindle of the tool and turning the collar to the locked position. The chuck will click when properly
installed.
Drilling
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool
from power source before making any adjustments or removing/installing attachments or
accessories.
WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is anchored
or clamped firmly. If drilling thin material, use a wood “back-up” block to prevent damage to the
material.
Press mode selector button (E) and turn the mode selector (D) to the drill bit symbol for drilling, to
the hammer symbol for hammering or to the hammerdrill symbol for hammerdrilling.
DRILLING OPERATION
1. For WOOD, use twist bits, spade bits, power auger bits or hole saws. For METAL, use high-
speed steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should be drilled dry. For MASONRY, use carbide-
tipped bits or masonry bits. A smooth, even flow of dust indicates the proper drilling rate.
2. Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill bit
biting, but do not push hard enough to stall the motor or deflect the bit.
3. Hold tool firmly with both hands to control the twisting action of the drill.
WARNING: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip
the drill firmly with both hands to control the twisting action and avoid injury.
JJ
F
C
D
E
F
G
J
I
HB
A
D25323
A
ED
J
I
F
G
H
C
D25223
E
G
B
4. IF DRILL STALLS, it is usually because it is being overloaded. RELEASE TRIGGER
IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT
CLICK TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL – THIS
CAN DAMAGE THE DRILL.
5. To minimize stalling or breaking through the material, reduce pressure on drill and ease the
bit through the last fractional part of the hole.
6. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent
jamming.
7. With variable speed drills there is no need to center punch the point to be drilled. Use a slow
speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep
enough to drill without the bit skipping out.
DRILLING IN METAL
An SDS Plus® to round shank adaptor chuck is required for the D25113, D25213, D25313,
D25223 and the D25323. Ensure that tool is in drill-only mode. Start drilling with slow speed and
increase to full power while applying firm pressure on the tool. A smooth even flow of metal chips
indicates the proper drilling rate. Use a cutting lubricant when drilling metals. The exceptions are
cast iron and brass which should be drilled dry.
NOTE: Large [5/16" to 1/2" (7.9 mm to 12.7 mm)] holes in steel can be made easier if a pilot hole
[5/32" to 3/16" (4 mm to 4.8 mm)] is drilled first.
DRILLING IN WOOD
An SDS Plus® to round shank adaptor chuck is required for the D25113, D25213, D25313,
D25223 and the D25323. Ensure that tool is in drill-only mode. Start drilling with slow speed and
increase to full power while applying firm pressure on the tool. Holes in wood can be made with
the same twist drills used for metal. These bits may overheat unless pulled out frequently to clear
chips from the flutes. For larger holes, use spade bits, power auger bits, or hole saws. Work that
is apt to splinter should be backed up with a block of wood.
HAMMERDRILL OPERATION
1. When drilling, use just enough force on the hammer to keep it from bouncing excessively or
“rising” off the bit. Too much force will cause slower drilling speeds, overheating, and a lower
drilling rate.
2. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the
bit when drilling as this will cause clogging of the bit flutes and a slower drilling speed.
3. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of
the hole with the tool still running to help clear debris from the hole.
4. For masonry, use carbide-tipped bits or masonry bits. A smooth even flow of dust indicates
the proper drilling rate.
Chipping and Chiselling (Fig. 1)
1. Set the mode selector switch (D) to the hammering only position.
2. Insert the appropriate chisel and rotate it by hand to lock it into one of 51 positions.
3. Adjust the side handle (I) as required.
4. Switch on the tool and start working.
5. Always switch off the tool when work is finished and before unplugging.
Depth Rod (Fig. 4)
TO ADJUST THE DEPTH ROD
1. Push in and hold the depth rod release button (J) on the side handle.
2. Move the depth rod (H) so the distance between the end of the rod and the end of the bit
equals the desired drilling depth.
3. Release the button to lock rod into position. When drilling with the depth rod, stop when end
of rod reaches surface of material.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool
from power source before making any adjustments or removing/installing attachments or
accessories.
Cleaning
WARNING: Blow dirt and dust out of all air vents with dry air at least once a week. Wear
proper ANSI Z87.1 (CAN/CSA Z94.3) eye protection and proper NIOSH/OSHA/MSHA
respiratory protection when performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Lubrication
Your tool was properly lubricated before leaving the factory. In from two to six months, depending
upon use, take or send your tool to an authorized service center for a complete cleaning,
inspection and lubrication. Tools used constantly on production jobs will need relubrication more
often. Also, tools “out of service” for long periods should be relubricated before being put back
to work.
Accessories
WARNING: Since accessories, other than those offered by D WALT, have not been tested E
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only DEWALT, recommended accessories should be used with this product.
Recommended accessories for use with your tool are available at extra cost from your local
dealer or authorized service center. If you need assistance in locating any accessory, please
contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call
1-800-4-DEWALT (1-800-433-9258) or visit our website www.dewalt.com.
MAXIMUM RECOMMENDED CAPACITIES
D25113, D25213, D25313
D25223, D25323, D25324
Masonry 1" (25.4 mm)
Steel 1/2" (12.7 mm)
Wood 1-1/2" (38 mm)
OPTIMUM CAPACITY
Masonry 5/32"–5/8" (4 mm–4.8 mm)
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments (including
brush inspection and replacement) should be performed by a DEWALT factory service center,
a DEWALT authorized service center or other qualified service personnel. Always use identical
replacement parts.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship for
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to
accessories or damage caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights which vary in certain
states or provinces.
In addition to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time
during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained either in the
packaging, call the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-DEWALT for a free replacement.
SPECIFICATIONS
D25113, D25213, D25313,
D25223, D25313, D25324 D25330
Voltage: 120 V AC~ 120 V AC~
Ampere rating: 8 A 6.3 A
Frequency: 60 Hz 60 Hz
RPM: 0–1 150/min –
Beats per minute 0–4 300 0–4 100
Définitions : lignes directrices en
matière de sécurité
Les définitions ci-dessous décrivent le niveau de danger pour chaque mot-indicateur
employé. Veuillez lire le mode d’emploi et porter une attention particulière à ces
symboles.
DANGER : indique une situation dangereuse imminente qui, si elle n’est pas
évitée, causera la mort ou des blessures graves.
AVERTISSEMENT : indique une situation potentiellement dangereuse qui, si elle
n’est pas évitée, se solder par unpourrait décès ou des blessures graves.
ATTENTION : indique une situation potentiellement dangereuse
qui, si elle n’est pas évitée se solder par pourrait des blessures mineures ou
modérées.
AVIS : aucun risque de dommages corporels indique une pratique ne posant mais
qui par contre, si rien n’est fait pour l’éviter, poser des pourrait risques de dommages
matériels.
POUR TOUTE QUESTION OU TOUT COMMENTAIRE RELATIF À CET OUTIL OU À
PROPOS DE TOUT AUTRE OUTIL DEWALT, COMPOSER SANS FRAIS LE : 1-800-4-DEWALT
(1-800-433-9258).
AVERTISSEMENT : afin de réduire le risque de blessures, lire le mode d’emploi de
l’outil.
Avertissements de sécurité généraux pour les outils
électriques
AVERTISSEMENT! Lire tous les avertissements de sécurité et les directives. Le
non-respect des avertissements et des directives pourrait se solder par un choc
électrique, un incendie et/ou une blessure grave.
CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES
LES DIRECTIVES POUR UN USAGE ULTÉRIEUR
Le terme « outil électrique » cité dans les avertissements se rapporte à votre outil électrique à
alimentation sur secteur (avec fil) ou par piles (sans fil).
1) SÉCURITÉ DU LIEU DE TRAVAIL
a) Tenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont
propices aux accidents.
b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, tel qu’en
présence de liquides, de gaz ou de poussières inflammables. Les outils électriques
produisent des étincelles qui pourraient enflammer la poussière ou les vapeurs.
c) Éloigner les enfants et les personnes à proximité pendant l’utilisation d’un outil
électrique. Une distraction pourrait en faire perdre la maîtrise à l’utilisateur.
2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ
a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais modifier
la fiche d’aucune façon. Ne jamais utiliser de fiche d’adaptation avec un outil
électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de fiches
non modifiées correspondant à la prise.
b) Éviter tout contact physique avec des surfaces mises à la terre comme des tuyaux,
des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc électrique est
plus élevé si votre corps est mis à la terre.
c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. La pénétration de l’eau
dans un outil électrique augmente le risque de choc électrique.
d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour
transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de
la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Les cordons
endommagés ou enchevêtrés augmentent les risques de choc électrique.
e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge convenant
à cette application. L’utilisation d’une rallonge conçue pour l’extérieur réduira les risques
de choc électrique.
f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit humide,
brancher l’outil dans une prise ou sur un circuit d’alimentation dotés d’un disjoncteur de
fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur réduit les risques de choc
électrique.
3) SÉCURITÉ PERSONNELLE
a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un outil
électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue ou sous
l’influence de drogues, d’alcool ou de médicaments. Un simple moment d’inattention
en utilisant un outil électrique peut entraîner des blessures corporelles graves.
b) Utiliser des équipements de protection individuelle. Toujours porter une protection
oculaire. L’utilisation d’équipements de protection comme un masque antipoussière, des
chaussures antidérapantes, un casque de sécurité ou des protecteurs auditifs lorsque la
situation le requiert réduira les risques de blessures corporelles.
c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve à la
position d’arrêt avant de relier l’outil à une source d’alimentation et/ou d’insérer un
bloc-piles, de ramasser ou de transporter l’outil. Transporter un outil électrique alors
que le doigt repose sur l’interrupteur ou brancher un outil électrique dont l’interrupteur est
à la position de marche risque de provoquer un accident.
d) Retirer toute clé de réglage ou clé avant de démarrer l’outil. Une clé ou une clé de
réglage attachée à une partie pivotante de l’outil électrique peut provoquer des blessures
corporelles.
e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet de
mieux maîtriser l’outil électrique dans les situations imprévues.
f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de bijoux.
Garder les cheveux, les vêtements et les gants à l’écart des pièces mobiles. Les
vêtements amples, les bijoux ou les cheveux longs risquent de rester coincés dans les
pièces mobiles.
g) Si des composants sont fournis pour le raccordement de dispositifs de dépoussiérage
et de ramassage, s’assurer que ceux-ci sont bien raccordés et utilisés. L’utilisation
d’un dispositif de dépoussiérage peut réduire les dangers engendrés par les poussières.
4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE
a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à l’application.
L’outil électrique approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse
pour laquelle il a été conçu.
b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil
électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.
c) Débrancher la fiche de la source d’alimentation et/ou du bloc-piles de l’outil
électrique avant de faire tout réglage ou changement d’accessoire ou avant de
ranger l’outil. Ces mesures préventives réduisent les risques de démarrage accidentel de
l’outil électrique.
d) Ranger les outils électriques hors de la portée des enfants et ne permettre à
aucune personne n’étant pas familière avec un outil électrique ou son mode
d’emploi d’utiliser cet outil. Les outils électriques deviennent dangereux entre les mains
d’utilisateurs inexpérimentés.
e) Entretien des outils électriques. Vérifier si les pièces mobiles sont mal alignées ou
coincées, si des pièces sont brisées ou présentent toute autre condition susceptible
de nuire au bon fonctionnement de l’outil électrique. En cas de dommage, faire
réparer l’outil électrique avant toute nouvelle utilisation. Beaucoup d’accidents sont
causés par des outils électriques mal entretenus.
f) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe
bien entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles à
maîtriser.
g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux
présentes directives en tenant compte des conditions de travail et du travail à
effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour laquelle
il a été conçu est dangereuse.
5) RÉPARATION
a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant que des
pièces de rechange identiques. Cela permettra de maintenir une utilisation sécuritaire
de l’outil électrique.
Consignes de sécurité additionnelles propres aux
marteaux rotatifs
• Porter un dispositif de protection auditif. Le bruit en résultant pourrait occasionner une
perte de l’acuité auditive.
• Utiliser les poignées auxiliaires fournies avec l’outil. Une perte de contrôle de l’outil
pourrait occasionner des dommages corporels.
• Tenir l’outil par les surfaces isolées prévues à cet effet pendant toute utilisation où
l’organe de coupe pourrait entrer en contact avec des fils électriques cachés ou son
propre cordon. Tout contact avec un fil sous tension met les parties métalliques exposées
de l’outil sous tension et électrocute l’utilisateur.
• Utiliser des serre-joints, ou tout autre moyen, pour fixer et immobiliser le matériau
sur une surface stable. Tenir la pièce à la main ou contre son corps offre une stabilité
insuffisante qui pourrait vous en faire perdre le contrôle.
• Porter des lunettes de protection ou toute autre protection oculaire. Le martelage
pourrait faire voltiger des éclats. Ces particules volantes pourraient occasionner des
dommages oculaires permanents. Porter un masque anti-poussières ou un appareil de
protection des voies respiratoires pour toute application productrice de poussières. Une
protection auditive peut s’avérer nécessaire pour la plupart des applications.
• Maintenir systématiquement l’outil fermement. Ne pas tenter d’utiliser cet outil sans
le maintenir à deux mains. Il est recommandé d’utiliser systématiquement la poignée
latérale. Le fait d’utiliser cet outil à une main pourra vous en faire perdre le contrôle. Traverser
ou rencontrer des matériaux durs comme les armatures peut aussi s’avérer dangereux.
Resserrer soigneusement la poignée latérale avant toute utilisation.
Produktspezifikationen
| Marke: | DeWalt |
| Kategorie: | bohren |
| Modell: | D25213K |
Brauchst du Hilfe?
Wenn Sie Hilfe mit DeWalt D25213K benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung bohren DeWalt
21 September 2024
20 September 2024
18 September 2024
17 September 2024
15 September 2024
12 September 2024
6 September 2024
6 September 2024
6 September 2024
5 September 2024
Bedienungsanleitung bohren
- bohren Basetech
- bohren Panasonic
- bohren Clas Ohlson
- bohren Cotech
- bohren Makita
- bohren Bosch
- bohren Flex
- bohren Laserliner
- bohren Parkside
- bohren Vonroc
- bohren AEG
- bohren Velleman
- bohren Powerfix
- bohren Black And Decker
- bohren Cocraft
- bohren FERM
- bohren Ryobi
- bohren Skil
- bohren Topcraft
- bohren Trotec
- bohren Maestro
- bohren Baier
- bohren Carat
- bohren Eibenstock
- bohren Hilti
- bohren Bort
- bohren Einhell
- bohren Elu
- bohren Festool
- bohren Mafell
- bohren Maktec
- bohren Worx
- bohren Luxor
- bohren Hikoki
- bohren Hitachi
- bohren Hyundai
- bohren Hazet
- bohren Kinzo
- bohren Kress
- bohren Max
- bohren Metabo
- bohren Stanley
- bohren Würth
- bohren Güde
- bohren Power Craft
- bohren Scheppach
- bohren Workzone
- bohren Biltema
- bohren Meec Tools
- bohren Dremel
- bohren Fieldmann
- bohren EcoMAC
- bohren Proxxon
- bohren Westfalia
- bohren Dedra
- bohren DURO
- bohren Graphite
- bohren Silverline
- bohren Holzmann
- bohren MSW
- bohren Huvema
- bohren Robust
- bohren Zipper
- bohren Stomer
- bohren Yato
- bohren Baumr-AG
- bohren Genesis
- bohren BluCave
- bohren Toolland
- bohren Delta
- bohren Batavia
- bohren Bavaria
- bohren Brüder Mannesmann
- bohren Milwaukee
- bohren Narex
- bohren Toolcraft
- bohren Fein
- bohren Verto
- bohren Craftsman
- bohren Powerplus
- bohren Rupes
- bohren ProfiTech
- bohren Alpha Tools
- bohren Ozito
- bohren Kawasaki
- bohren Sun Joe
- bohren Ridgid
- bohren Porter-Cable
- bohren VARO
- bohren Duro Pro
- bohren Economy
- bohren Fe Powertools
- bohren Gamma
- bohren Global
- bohren Goon
- bohren Lux Tools
- bohren Max Bahr
- bohren Protool
- bohren Spit
- bohren Steren
- bohren Tanaka
- bohren Meister Craft
- bohren Malmbergs
- bohren Truper
- bohren RIKON
- bohren Kreg
- bohren G-Technology
- bohren Einhell Bavaria
- bohren Powerblade
- bohren Rok
- bohren Tryton
- bohren MyTool
- bohren McKenzie
- bohren Rodcraft
- bohren Ribimex
- bohren Black Decker
- bohren RUKO
- bohren Handwerk
- bohren Stalco
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024
15 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024