Delta Dore Tyxia 611 Bedienungsanleitung

Delta Dore Erleichterung Tyxia 611

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Delta Dore Tyxia 611 (1 Seiten) in der Kategorie Erleichterung. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/1
The TYXIA 611 pack enables
you to create a two-way lighng
without an exisng switch.
Recommendaons
IMPORTANT: the control wires are not
insulated from the mains power supply.
All connected equipment must be marked CE
and meet the requirements of the low voltage
devices as well as assembly recommendaons.
Local control wires can be extended up to 10
m (separate from the 230 V).
10A circuit breaker required.
Step 1 - Install your products
230V~
OFF
You can install the lighng receiver in a flush-mounted
box, behind a switch or control push-buon
(automac detecon on use) or behind a ceiling.
1.1 Connecon instrucons for terminals 1 2 3 4.
Strip the wires while respecng the strip length specified on the product.
1.1.1 Solid wires 1.1.2 Stranded wires
Push the wire fully
into the terminal.
Removal recommendaons
- Switch off the power supply.
- Use the tool supplied or a 2.5 mm screwdriver
to press the buon of the front terminal before
removing the wire. 2
1
1.2 Connecon instrucons for IN1 - COM - IN2 terminals
Use the wires supplied.
Push the wire fully into the terminal.
1.3 TYXIA 5610 connecon
Connect:
The light to terminals 3 and 4.
The switch to the IN1 -
COM terminals (input 1).
The 230 V power supply to terminals 1
and 2.
Switch the installaon power back on to
connue with the associaon operaon.
1.4 TYXIA 2310 installaon
This unit must not be placed on a metal surface.
Configuraon buons
Step 2 - Determine the operang mode of the TYXIA 2310
The operang mode of the TYXIA 2310 is, by default, mode A, i.e. for control-
ling 2 ON/OFF lighng channels.
IMPORTANT: If you approve this selecon, go directly to step 3,
'Associate your products'.
Otherwise, determine the operang mode suited to your installaon.
Mode B: Scenario mode to simultaneously control different receivers.
Mode C: Dimmer mode to control a dimmer lighng channel.
Open the unit.
Press the T2 buon several mes to select
your desired operang mode.
...... ...
EXIT
1
2
ON/OFF
ON/OFF
... ... ...
Mode A Mode B Mode C
The LED fl ashes
once
The LED fl ashes
twice
The LED fl ashes
three  mes
Step 3 - Associate your products
❶Set the TYXIA 5610 receiver to associaon
standby mode. Press and hold the buon for 3
seconds unl the LED flashes, release.
❷ On the TYXIA 2310 emiers, send the
associaon order: Mode A or B: Press the
buon of the channel you want to associate
for 3 seconds (1 or 2).
Mode C: Press the 1 and 2 buons
at the same me and hold for 3 seconds.
❸ When the receiver LED has stopped flashing.
The products are now associated.
Number of associated emiers: 16 maximum
Troubleshoong
Summary of funcons accessible using the receiver buon
3’’
A
>10’’ 20’’>
C
>
B
Associaon/
Configuraon
Removing an
associaon
Removing
all associaons
Press and hold the buon for x seconds
AAssociaon/Configuraon
Press the receiver buon for 3 seconds unl the LED flashes, release.
BRemove an associaon
On the TYXIA 5610 receiver:
Press the receiver buon for 10 seconds unl the LED flashes rapidly, release.
On the TYXIA 2310 emier:
Mode A or B: Press the buon of the channel you want to delete for 3 seconds
(1 or 2).
Mode C: Press the 1 and 2 buons at the same me and hold for 3 seconds.
CRemove all associaons
Press the receiver's buon for 20 seconds.
Press and hold unl the LED switches off aer the rapid flashing phase, release.
The receiver has no wireless connecon.
The receiver locks in off mode
When an overload is detected, the product locks in off mode for 30 seconds be-
fore authorising a new acvaon. The LED flashes rapidly throughout this phase.
To exit the receiver from this secure mode, replace the bulb connected by a bulb
with lower power (refer to compability table).
You wish to change the operang mode of a product which has already been
associated. - You must first delete any associaon.
Replacing the baeries
Red Red Red
2s
The red LED flashes each me you press = Baery fault
Compability
① 230 V halogen or 230 V incandescent bulbs.
② 230V energy-saving compact fl uorescent bulbs.
③ 230V LED bulbs.
④ Very low voltage 12V halogen or LED bulbs with AC or DC electronic
transformer.
⑤Very low voltage 12V halogen bulbs with ferromagne c or toroidal transformer.
⑥Fluorescent tube.
200 W 100 W 100 W100 W100 W
LEDLED
150 W 100 W
M
Hi-Fi
230 V~ 50 Hz
2
1
230 V~
1
IN1
COM
TYXIA
5610
1 2 3 4
230V~
200W max
1234
Standby 0.06W
230 V~ 0.6 VA
IN1
CO M
IN1
CO M
ON
OFF
ON
OFF
230V~
µ
N S1NL
2
7mm 0,5 mm
KY31A02
123 4
230V
EN
Technical characteriscs
TYXIA 5610
- Power supply 230 V~ 0.6 VA
- Class II insulaon
Stand-by consumpon: 0.06 W
- Storage temperature: -10 °C / +70 °C
- Operang temperature: -10 °C / +40 °C
- IP 40 (flush mounng box)
- Dimensions: 41 x 36 x 14.5 mm
- X3D wireless remote control device:
868.7 MHz to 869.2 MHz
- Maximum wireless power < 10 mW Category 2 receiver
TYXIA 2310
- CR 2430 lithium baery power supply (included),
Baery life 10 years depending on use
- Storage temperature: -10 °C / +70 °C
- Operang temperature: -10 °C / +40 °C
- IP 40 - IK 04
- Dimensions: 84 x 84 x 13 mm
- X3D wireless remote control device:
868.7 MHz to 869.2 MHz
- Maximum wireless power < 10 mW Category 2 receiver
EN Wireless two-way pack
Use an electrically
isolated tool to per-
form the acons on
the receiver configu-
raon buon.
TYXIA
Switch off the installaon
power supply.
Do not strip the wires when they are
connected to the product as you
could damage the internal connector.
1 2 3 4
TYXIA
5610
TYXIA
5610
... ... ...
> 3s
µ
N S1NL
µ
N S1NL
1 2 3 4
TYXIA
5610
OK
OFF
µ
N S1NL
1
2
>3s
>3s
1
2
Removal recommendaons
Turn the wire while pulling on it.
1
2
123 4
TYXIA 2310
TYXIA 2310
TYXIA 5610
On / Off
On / Off
Alim. 230 V
230 V
200 W maxi.
TYXIA 611 pack
Using the tool
supplied or a 2.5
mm screwdriver,
press the terminal
buon then insert
the wire.
Important : If you have selected opera ng mode B (scenario
control), set each item to the required state (e.g. shu ers
lowered, ligh ng off ) before moving on to stage 1.

Produktspezifikationen

Marke: Delta Dore
Kategorie: Erleichterung
Modell: Tyxia 611

Brauchst du Hilfe?

Wenn Sie Hilfe mit Delta Dore Tyxia 611 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Erleichterung Delta Dore

Delta Dore

Delta Dore Tyxia 611 Bedienungsanleitung

13 August 2024
Delta Dore

Delta Dore Tyxia 620 Bedienungsanleitung

12 August 2024
Delta Dore

Delta Dore Easy Bulb E27CW Bedienungsanleitung

10 August 2024
Delta Dore

Delta Dore Easy Plug G13EM Bedienungsanleitung

9 August 2024
Delta Dore

Delta Dore Tyxia 6610 Bedienungsanleitung

8 August 2024
Delta Dore

Delta Dore Tyxia 501 Bedienungsanleitung

7 August 2024

Bedienungsanleitung Erleichterung

Neueste Bedienungsanleitung für -Kategorien-

Goobay

Goobay 30780 Bedienungsanleitung

16 Oktober 2024
AFX

AFX Grace GRCP07CBBK Bedienungsanleitung

13 Oktober 2024
AFX

AFX Point PNTP0107L30D1BK Bedienungsanleitung

13 Oktober 2024
Smartwares

Smartwares 20.003.54 Bedienungsanleitung

9 Oktober 2024
Neewer

Neewer TL97C Bedienungsanleitung

8 Oktober 2024
Neewer

Neewer SRP18C Bedienungsanleitung

8 Oktober 2024
Qtx

Qtx Moonglow Bedienungsanleitung

7 Oktober 2024
Blumfeldt

Blumfeldt Shinecube XL Bedienungsanleitung

7 Oktober 2024
Qtx

Qtx HPWash100 Bedienungsanleitung

6 Oktober 2024
BeamZ

BeamZ DJ X5 Bedienungsanleitung

5 Oktober 2024