Davis DAV-7747 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Davis DAV-7747 (16 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/16
1
Daytime Fan-Aspirated Radiation
Shield Kit Installation Manual
For Vantage Pro2â„¢ & Vantage Pro2 Plusâ„¢ Stations
Introduction
The instructions describe how to upgrade a non-aspirated Vantage Pro2 radia-
tion shield to a Daytime Fan-Aspirated Radiation Shield.
The upgrade kit can be installed on any Vantage Pro2 or Vantage Pro2 Plus
Integrated Sensor Suite (ISS) equipped with a non-aspirated radiation shield.
Components
The upgrade kit includes the following components:
Closed Cap Plate
Open Cap Plate
Open Plate
SIM Cover
Fan Plate
Daytime Fan Kit Components
Davis Instruments, 3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A. • 510-732-9229 • www.davisnet.com
®
Installing the Daytime Fan Kit
2
The kit also includes the following hardware:
Tools Needed
You may need some or all of the following tools to complete the upgrade:
• A medium Phillips-Head screwdriver
• A medium slot-tip screwdriver
• Other tools as required to remove and re-mount the ISS
Installing the Daytime Fan Kit
Installation Overview
These are the steps to install the Daytime Fan components:
1. — Put the console into Setup Mode.For Consoles Only
2. Take the ISS down from its installed position.
3. Disassemble the standard radiation shield.
4. Check Temperature/Humidity sensor orientation.
5. Assemble the lower section of the fan-aspirated shield.
6. Install the fan unit.
7. Assemble the upper section of the fan-aspirated shield.
8. Re-Install the ISS.
9. Take the console out of Setup Mode.
For Consoles Only— Put Console in Setup Mode
If you have a console, you need to put it in Setup Mode. This prevents the
reception of erroneous data while you are removing the ISS.
If you have an Envoy and are concerned with erroneous data, you may edit the
data via the WeatherLink software. See the WeatherLink Online Help for more
information.
#8-32 x 3-1/4" Screws
(3)
#8-32 x 1/2" Screws
(3) Threaded Spacers
(3)
#8 Split-Lock Washers (6)
#8 Flat Washers (6)
12" Cable Ties (2)
Daytime Fan Kit Hardware
Installing the Daytime Fan Kit
3
To put your console in Setup Mode:
At your Vantage Pro2 console, press and hold DONE and then press the
down arrow (-) to put the console in Setup Mode. This prevents the
reception of erroneous data while you are removing the ISS.
Note: If the console acquires erroneous data during the upgrade, see Take the Console Out
of Setup Mode on page 16 for instructions on clearing data. Additional information on
clearing console data can be found in the .Vantage Pro2 Console Manual
Take Down the ISS
Please work on your Vantage Pro2 ISS in a safe place. If you are installing the
Daytime Fan Kit on an ISS that has already been placed into service, you will
need to take down the ISS from its sited location and move it to a convenient
and safe place to perform the installation.
To disassemble the ISS:
1. Locate the Sensor Interface
Module (SIM) housing cover
on the side of ISS and open it.
2. Disconnect the Solar Panel
wire on the SIM cover from
the SIM board by pulling the
Solar Panel connector.
3. Pull the foam insert out of the
cable access port in between
the cables and set the foam
insert aside.
4. Disconnect the anemometer
cable from the sensor
connector labeled WIND and,
if you are using a cabled
model, disconnect the console
cable from the SIM and slide
the cables out of the cable
access port.
5. You can now remove the ISS from its mounted position. Move it to a safe
place to install the kit components.
Disassemble the Standard Radiation Shield
Note: We recommend using a workbench or table to perform the following procedures.
1. Open and remove the SIM cover if you have not done so already.
2. Disconnect the Temperature/Humidity cable from the SIM and slide the
cable out of the cable access port.
Lift off cover,
unplug solar power
connector
Detaching the SIM Cover


Produktspezifikationen

Marke: Davis
Kategorie: Nicht kategorisiert
Modell: DAV-7747

Brauchst du Hilfe?

Wenn Sie Hilfe mit Davis DAV-7747 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Davis

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-