DataComm 45-0022-WH Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr DataComm 45-0022-WH (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Parts Included:
1. 45-0021-WH Recessed Low Voltage Cable Plate
with Recessed Power
2. Recessed Low Voltage Cable Plate with Recessed
Locking Inlet
3. 6 Ft. 14/2 with Ground Extension Cord
Use the Recessed Low Voltage Cable Plate with Recessed
Locking Inlet to install power and low voltage cables behind your
flat panel TV, amplifier or other audio and video devices to your
equipment room or at the location of your head end equipment.
IMPORTANT INSTRUCTIONS:
 Use the local electrical code approved installation when
installing this product.
 The electrical parts in this kit are designed to be used
only as a kit and none of these electrical parts are
designed to be used individually.
 This product is not designed to be part of your home or a
commercial building’s electrical wiring system.
 This installation is only energized (electrically active)
when the supplied 6 ft. cord is plugged into the recessed
locking inlet located on the recessed low voltage cable
plate and the locking end of the 6 ft. cord is plugged into
either your surge protector or wall receptacle.
 If you are not familiar with home wiring systems, please
call a qualified electrician to install this product.
Installation Instructions for New Construction:
Simply use a new nail on box and follow all other instructions
described in the retrofit portion of the instruction sheet.
Installation Instructions for Retrofit Only:
1. Select the location of your flat panel TV mounting
bracket. Now select the location for both the 45-0021-
WH Recessed Low Voltage Cable Plate with Recessed
Power and the Recessed Low Voltage Cable Plate with
Recessed Locking Inlet.
2. Both the Recessed Low Voltage Cable Plate with
Recessed Power and the Recessed Low Voltage Cable
Plate with Recessed Locking Inlet are designed to be
mounted between two studs (see Figure 1). Using the
template supplied (see back of instruction sheet), trace
the openings needed for both recessed cable plates.
Using a drywall knife cut a hole in the drywall the size of
the template.
3. Remember that the Pro-Power kit is not part of your
home’s electrical wiring system. Before installing the
single gang retrofit workboxes (see Figure 2), pull a
piece of 12/2 or 14/2 with ground UL approved building
wire from one opening to the other opening to connect
the recessed cable plate with recessed power to the
recessed cable plate with recessed locking inlet. Make
sure the piece of wire is long enough to allow for easy
installation of the receptacles. Insert a single gang
retrofit workbox (see Figure 2). Securely fasten the
workbox to the wall.
DataComm Electronics, Inc.
6349 Peachtree Street
Norcross, GA 30071-1725
888.223.7977
770.662.8205
www.datacommelectronics.com
Instruction / Installation Sheet
DataComm Electronics 45-0022-WH Recessed Pro-Power Kit with Locking Inlet
Figure 3 Figure 4
Figure 1 – Front View
Figure 2 – Back View
3/22/10 Rev. 8
4-11/16”
Installation Instructions 45-0022-WH (continued):
4. To connect the receptacle on the Recessed Cable Plate with
Recessed Power to the piece of 12/2 or 14/2 with ground UL
approved building wire that you pulled from one opening in the
drywall to the second opening in the drywall, strip off
approximately 3 inches of the outer jacket of the UL approved
building wire. Be careful not to cut the jacket of the inner wires.
Connect the hot line (black) wire to the brass colored terminal
screw and neutral (white) wire to the silver colored terminal
screw. Be sure to connect the bare grounding wire to the green
colored terminal screw (see Figure 3).
5. Once you have wired the Recessed Cable Plate with Recessed
Power receptacle, begin by inserting the receptacle portion of
the plate into the retrofit work box. Once the entire recessed
plate is flush to the wall, using the two white screws supplied,
screw the receptacle portion of the plate to the work box. Next,
screw down the screws with wings. The wings will fasten tightly
against the back of the drywall. Plug all necessary video and
audio cables through the opening on the Recessed Cable Plate
with Recessed Power and down the wall to the opening you cut
out for the Recessed Cable Plate with Recessed Locking Inlet.
6. To connect the Recessed Cable Plate with Locking Inlet to the
UL approved 12/2 or 14/2 building wire with ground, fully back
out the brass and silver terminal clamps. Insert building wire
conductors into the proper wire well. Insert the hot line (black)
wire into the wire well with the brass screw, insert the neutral line
(white) wire into the wire well with the silver screw. Once the
building wire is inserted into the proper wire well, tighten terminal
screws firmly to 10-12 in.-lbs. Then connect the grounding solid
copper wire to the green grounding screw located on the end of
the locking inlet (see Figure 4). Make sure the solid copper
grounding wire is securely fastened onto the green grounding
screw and properly grounded. Plug all necessary video and
audio cables through the opening on the Recessed Cable Plate
with Locking Inlet. Insert the locking inlet portion of the plate into
the retrofit work box. Once the entire recessed plate is flush to
the wall, using the two white screws supplied, screw the locking
inlet portion of the plate to the work box. Next, screw down the
screws with wings. The wings will fasten tightly against the back
of the drywall. Make sure to keep your UL approved building
wire away from the video and audio cables (see Figure 2).
7. Install your flat panel TV mounting bracket per the flat panel TV
bracket manufacturer’s instructions. Make sure to read all
instructions.
8. Now plug your flat panel TV or TV/Projector into the Recessed
Cable Plate with Recessed Power (see Figure 1). Then plug
the female end of the supplied 6 ft. cord into the Recessed
Cable Plate with Recessed Locking Inlet (see Figure 2) and
male end into either your surge protector or wall receptacle.
9. For shock protection, both the UR, UL recognized receptacle
and inlet components must be properly grounded.
10. Caution – use copper wire only with this receptacle and inlet.
WARNING
 DataComm Electronics’ products shall be installed and
used only as indicated in DataComm Electronics’ product
instruction sheets.
 Instruction sheets are available online at
www.datacommelectronics.com.
CAUTION
 For shock protection, this device must be properly
grounded.
 Use copper wire only with this device.
IMPORTANT INSTRUCTIONS
 Read and understand all instructions.
 Follow all warnings and instructions marked on the product.
 Do not use this product near water, for example near a bath
tub, wash bowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
 SAVE THESE INSTRUCTIONS.
3/22/10 Rev. 8
ONLY LICENSED PROFESSIONALS SHOULD INSTALL THIS PRODUCT
This product is patent protected by U.S. Patent numbers D553475, D554475 and 7390964.
Multiple patents pending. RoHS Compliant.
TEMPLATE
45-0021-WH Recessed Cable Plate
with Recessed Power
&
45-0022-WH Recessed Low Voltage
Cable Plate with Recessed Locking
Inlet
A
CTUAL SIZE
CUT ALONG DOTTED LINE 
3-3/4”


Produktspezifikationen

Marke: DataComm
Kategorie: Nicht kategorisiert
Modell: 45-0022-WH

Brauchst du Hilfe?

Wenn Sie Hilfe mit DataComm 45-0022-WH benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert DataComm

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-