Danfoss ICAD 600B Bedienungsanleitung

Danfoss Nicht kategorisiert ICAD 600B

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Danfoss ICAD 600B (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/6

Installation guide

Actuator

Type ICAD 600B / 600B-TS / 1200B

027R9001

Info for UK customers only : Danfoss Ltd., 22 Wycombe End, HP9 1NB, GB

Імпортер:ТОВ з іі “Данфосс ТОВ” 04080, Київ 80, п/с 168, Україна

Nm LB-feet

ICAD 600B

ICAD 600B-TS

ICAD 1200B

ICM + ICAD 600B/ICAD 600B-TS

1 2

3 4

5a 5b ICM + ICAD 1200B

Before installing ICAD on ICM please read

t she eparate guide

“Mechanical in Itallation ICAD onof CM”

ICAD 600B

ICAD 600B-TS

ICAD 1200B

mm in.

H45 1.77

L325 1

ring

Groove where

clamps hold onto

ICM top

New O-ring

“Quick start guide”

DANFOSS

Buttons and display description in page 4

Max. 3 Max. 2.2

ICAD 600B / ICAD 600B / ICAD 1200B

ICAD 600B/1200B - Analog I/O for modulating control

ICAD 600B/600B-TS/1200B - Digital I/O for ON/OFF valve operation

External

voltage

24 V DC (+)

(–)

II III

Supply

D F G E

DI1 DI2

Control

ICAD

Danfoss

M27H0163_1

Neutral zone/3 points control

Control

Power supply cable

cable

Terminal box

Data cabl e

Power

Control

Data

(White/blue)

(White/orange)

(Orange)

(Blue)

A (Black)

(Black)

(White)

(Brown)

(Blue)

B (Brown)

C (Red)

D (Orange)

E (Yellow)

F (Green)

G (Blue)

ICAD back Ref Color

A (Black)

B (Brown)

C (Red)

D )(Orange

E (Yellow)

F )(Green

G (Blue)

EKC 347

EKC 315A

EKC 361

Only possible with EKC 347

A (Black)

B (Brown)

C (Red)

D (Orange)

E (Yellow)

F (Green)

G (Blue) EKE 347

Only possible with EKE 347

A (Black)

B (Brown)

C (Red)

D )(Orange

E (Yellow)

F )(Green

G (Blue)

Auxiliary relays

24 V DC

A Black - Common alarm

B Brown - ICM fully open

C Red - ICM fully closed

D Orange - GND ground

E Yellow + 0/4 – 20 mA Input

F Green + 0/2 – 10 V input or digital input for on/o control

G Blue + 0/4 – 20 mA Output

I Black + Fail safe supply. Batter 19y / UPS* V DC

II White + Supply voltage

24 V DC 2A, or more, per ICAD recommended

ICAD PSU must be SELV**, >15 W

III Brown -

IIII Blue +UPS Signal of Health - optional depending on ID31:

‘UPS supply’ set to ‘Yes’

Digital

output

1 White/Blue

2 White/Orange

3 Blue

4 Orange

(-) / TX+ Data – (B) / Transmit Pair(+)

GND / RX+ Ground / Receiving Pair(+)

(+) / TX- Data + (A) / Transmit Pair(-)

GND / RX- Ground / Receiving Pair(-)

*Uninterruptable Power Supply

The ICAD is a Class III appliance

RS 485 / Ethernet

Description

ENGLISH

Installation

Do not install ICAD before welding. This apply for

electrical as well as for mechanical installation. Please

observe that ICAD when connected to 24 V DC, will

send out acoustic noise at stand still. This has no

inuence on the function/ operation of the ICAD.

Use

ICAD 600B, ICAD 600B-TS and ICAD 1200B can

be used together with the following Danfoss

valves (g. 1, 5a and 5b).

ICAD 600B ICAD 600B-TS ICAD 1200B

ICM 20 ICMTS 20 ICM 40

ICM 25 ICMTS 50 ICM 50

ICM 32 ICMTS 80 ICM 65

ICM 100

ICM 125

ICM 150

CVE pilot valve

Electrical data

Supply voltage is galvanically isolated from in-/output.

ICAD is a Class III product.

PSUs connected to ICAD must be SELV<100 VA

For UL compliance: PSU must be Class 2 NEC

Supply voltage

24 V DC (Tolerances; see below table)

Load ICAD 600B, ICAD 600B-TS: 1.2 A

ICAD 1200B: 2.0 A

24 Volt DC ONLY

Please observe cable voltage drop.

Distance between the applied DC transformer

and the ICAD terminal box may cause a

voltage drop. Cross section of cables and size

of DC transformer must be calculated so that

the voltage at all time at the ICAD terminal

box*, both during standstill and during

operation of ICAD, is within this range:

Prefabricated

ICAD cable length

Code number

1.5 m

027H0426

3 m

027H0438

10 m

027H0427

15 m

027H0435

Voltage ICAD terminal

(600B/1200B) [V DC]

Min. 21 22 23 24

Max. 26.4

* Do not measure inside the ICAD itself (value can be

checked in ICAD B menu).

Fail safe supply

24 V DC (Tolerances; see table above)

Load ICAD 600B, ICAD 600B-TS: 1.2 A

ICAD 1200B: 2.0 A

Data communication

RS 485: It is important that the installation of the data

communication cable is done correctly. For further

guidance, see literature No. RC8AC902.

Remember termination at the bus termination.

Max lenght of cable: 1200 m with specic cable and

limited data rate. Follow RS485 standard.

Insulation from power supply input, metallic part

and interface output : 500 V DC: *For input/output

connections

Anolog Input - Current or Voltage

Current

Input range: 0/4 – 20 mA

Max input range: 0 – 24 mA

Input resistance: 120 + diode voltage 0.7 V DCW

Measurement error: <±1.5% of the full scale

Reverse polarity protection: yes

Overcurrent protection: yes

Voltage

Input range: 0/2 – 10 V DC

Max input range: 0 – 12 V DC

Measurement error: <±1.5% of the full scale

Reverse polarity protection: yes

Analog Output

Output range: 0/4 – 20mA

Load: <800 W

Output error: <±1.5% of the full scale

Recommended external resistor for Hot application:

Rext=800 W-load 1W power rate

Digital Input - Digital ON/OFF input by means of voltfree

contact (Signal/Telecom relays with gold-plated contacts

recommended) – Voltage input used

Rth rise(OFF): >10 kW

Rth fall(ON): < 45 W

Digital Output - 3 pcs. NPN transistor output

External supply: 7 – 24 V DC (same supply as for

ICAD can be used, but please note

that the galvanically isolated

system will then be spoiled).

On resistance: 55 W + diode voltage 0.7 V DC

Max 70 at 50 mAW

Max Output current: 50 mA

Reverse polarity protection: Yes

Overcurrent protection: No

Temperature range (ambient)

-30 °C/+50 °C (-22 °F/122 °F)

Enclosure

IP67 (~NEMA 6)

Electrical connection

Connection to ICAD is done via M12 connectors. ICAD has

two M12 male and one M12 female connectors build-in:

Power supply: 4 poled M12 male connector

Control signals: 8 poled M12 male connector

Data communication: 4 poled M12 female connector

Power Supply cable with 4 poled M12 female connector

4 x 0.34 mm

2 (4 x ~22 AWG) (g. 6)

I: Black (+) 19 – 24 V DC fail safe

supply (optional)

II: White (+) 24 V DC

III: Brown (–) 24 V DC

IIII: Blue (+) UPS signal of health

Control cable with 8 poled M12 female connector

7 x 0.25 mm

2 (7 x ~24 AWG) (g. 7)

A: Black (–) Digital output

Common Alarm

B: Brown (–) Digital output

ICM fully open

C: Red (–) Digital output

ICM fully closed

D: Orange (–) GND - Ground

E: Yellow (+) Analog input 0/4 – 20 mA)

F: Green (+) Analog input 0/2 – 10 V /

DI1 - Digital ON/OFF input.

G: Blue (+) Analog output 0/4 – 20 mA)

Data communication cable with 4 poled M12 male

connector:

RS 485 / RS 485 /

Ethernet Ethernet

1: White/Blue (-) / TX+ Data – (B) / Transmit

Pair(+)

2: White/Orange GND / RX+ Ground / Receiving

Pair(+)

3: Blue (+) / TX- Data + (A) / Transmit

Pair(-)

4: Orange GND / RX- Ground / Receiving

Pair(-)

Electrical installation

General procedure for ICAD 600B/ICAD 600B-TS/1200B

installed on all ICM, ICMTS & CVE valves.

All necessary electrical connections to be made.

Fig. 6

Analog operation - 7 wired cable (A-G)

Modulation control. Valve to be controlled from

Danfoss electronics, type EKC/EKE (g. 7), or third

party electronics (like e.g. PLC).

Connect analog input signals. Currrent (mA) or

Voltage (V). See for conguration Parameter list

of analog input signals

Yellow (+) and Orange (GND) are used for current

(mA) input

Green (+) and Orange (GND) are used for Voltage

(V) input

Blue (+) and Orange (GND) are used for current

(mA) output (optional, not mandatory)

Fig. 6

Digital operation - 7 wired cable (A-G)

ON/OFF ICM solenoid valve operation. ICM valve to

be controlled by means of a digital voltfree contact.

Connect digital input signals (g. 8). See

Parameter list for conguration of digital input

signals

Green (+) and Orange (GND) are connected to a

voltfree contact

Digital output signals are optional, not mandatory.

Black (–) and Orange (GND) are connected to

auxiliary relay for Common Alarm

Brown (–) and Orange (GND) are connected to an

auxiliary relay indicating ICM fully open

Red (–) and Orange (GND) are connected to an

auxiliary relay indicating ICM fully closed

Supply voltage - 4 wired cable(I, II, III, IIII)

ICAD must be connected to a normal 24 V DC

supply. As an option, a fail safe supply is possible by

means of a battery or UPS (Uninterruptible Power

Supply). When voltage is applied as described

below, ICAD is ready to be congurated.

See . Parameter list

ICAD conguration can be done independently

whether the ICAD is installed on the valve or not.

See .Mechanical installation

Connect the White (+) and Brown (–) to 24 V DC

supply voltage (g. 6)

Fail safe supply as an option (not mandatory).

Connect the Black (+) and Brown (–) to a fail safe

supply.

Mechanical installation

General procedure for ICAD 600B/ICAD 600B-TS/1200B

installed on all valves (g. 3).

Check that the two socket screws are fully

unscrewed counter clockwise with a

3 mm Hexagon key

If valve is tted with PTFE ring and O-ring, remove

both and replace it with O-ring included in ICAD

(as instructed in g. 3)

Mount ICAD by slowly lowering it on top of the

valve.

The magnet coupling will drag the valve and ICAD

together and in position

Push ICAD in place

Fasten valve and ICAD with the two socket set

screws using a 3 mm Hexagon key

Special moisture seal is damaged if screws are

removed (g. 3).

Produktspezifikationen

Marke:	Danfoss
Kategorie:	Nicht kategorisiert
Modell:	ICAD 600B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Danfoss ICAD 600B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Nicht kategorisiert Danfoss

Danfoss DHRCP Bedienungsanleitung

4 September 2024

Danfoss VLT MCD 202 Bedienungsanleitung

2 September 2024

Danfoss SVA-140B Bedienungsanleitung

29 August 2024

Danfoss District Heating Substations Bedienungsanleitung

28 August 2024

Danfoss ICAD 600B Bedienungsanleitung

28 August 2024

Danfoss EKE 400 Bedienungsanleitung

27 August 2024

Danfoss ICMTS 50 Bedienungsanleitung

3 Mai 2024

Danfoss LLS 4000 Bedienungsanleitung

2 November 2023

Danfoss SFA 10 Bedienungsanleitung

2 November 2023

Danfoss ICSH 25-65 Bedienungsanleitung

7 August 2023

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-

DAS Audio AX-112-5 Bedienungsanleitung

16 Oktober 2024

Ferplast Ergocomfort Freetime Bedienungsanleitung

16 Oktober 2024

AEG MECK52 Bedienungsanleitung

16 Oktober 2024

Makita UR012G Bedienungsanleitung

16 Oktober 2024

Stihl HT 70 Bedienungsanleitung

16 Oktober 2024

Ernesto H14270 Bedienungsanleitung

16 Oktober 2024

IFM AC901S Bedienungsanleitung

16 Oktober 2024

Nedis RFPOM120FBK Bedienungsanleitung

16 Oktober 2024

AEG E9KLCS01 Bedienungsanleitung

16 Oktober 2024

ART ProChannel II Bedienungsanleitung

16 Oktober 2024