Da-Lite Wireline Advantage 29454G Bedienungsanleitung
Da-Lite
Projektionsleinwand
Wireline Advantage 29454G
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Da-Lite Wireline Advantage 29454G (12 Seiten) in der Kategorie Projektionsleinwand. Dieser Bedienungsanleitung war für 31 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/12
INSTRUCTION BOOK FOR
Wireline™ Advantage®
2
Tools Required for Installation
Important Safety Instructions
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so it will not be tripped over, pulled or contact
hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the
manufacturer may cause a risk of ire, electric shock, or injury to
persons.
6. Do not allow children to play with ixed controls. Keep remote
controls away from children.
7. Frequently examine the installation for imbalance and signs of
wear or damage to cables. Do not use if repair or adjustment is
necessary.
8. Appliance is not to be used by persons, including children, with
reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given
supervision or instruction.
9. Failure to provide adequate structural strength for this
component can result in serious personal injury or damage to
equipment! It is the installer’s responsibility to make sure the
structure to which this component is attached can support the
weight of all equipment. Reinforce the structure as required
before installing the component.
10. Use this projection screen only for its intended use as described
in these instructions. Do not use attachments not
recommended by the manufacturer.
Save These Instructions
1/4", 7/16" and 3/4“
Open Wrench or
Socket Driver
1/8“ Hex Key
(included)
Original Instructions
Disclaimer
Milestone and its ailiated corporations and subsidiaries
(collectively "Milestone"), intend to make this manual accurate
and complete. However, Milestone makes no claim that the
information contained herein covers all details, conditions or
variations, nor does it provide for every possible contingency in
connection with the installation or use of this subject to change
without notice or obligation of any kind. Milestone makes no
representation of warranty, expressed or implied, regarding the
information contained herein. Milestone assumes no
responsibility for accuracy, completeness or suiciency of the
information contained in this document.
Da-Lite® is a registered trademark of Milestone AV Technologies.
All rights reserved.
#3 Phillips
Screwdriver
3
1. The case provides multiple attachment Ceiling Mount:
points for bolts, cables, or threaded rod. Page 4 shows
threaded rod installed. The variable position-mounting
bracket may be located anywhere along the length of the
case. It is recommended to keep the brackets spaced evenly
enough to distribute the weight of the screen. One
mounting bracket is required for every 4' of case length.
Wall Mount: For use with optional langeless case only. The
variable position wall mounting brackets (sold separately)
may be located anywhere along the length of the case. It is
recommend to keep the brackets spaced evenly enough to
distribute the weight of the screen. One mounting bracket is
required for every 4' of case length.
2. Tighten bolts until trim lange is lush with Ceiling Mount:
ceiling.
Wall Mount: Remove lat brackets from top of case and
discard. Save bolts to attach wall brackets to case. Determine
spacing of wall brackets and attach to wall. Hoist screen to
brackets and completely tighten bolts attaching case to wall
brackets.
NOTE: For proper operation, screen assembly must be level
after installation.
3. Remove the silver shipping brackets that attach the slat to
the screen case. Use the supplied 1/8" hex key to remove the
set screws and a 1/4" socket to remove the screws from the
slat bar.
4. Using a 7/16" wrench and #3 Phillips screwdriver, remove the
shipping bracket that is attached to the roller. Once the
white wire is disconnected, feed it into the junction box in
order to complete the electrical installation. See Figure 1.
NOTE: Depending on the inal postion of the screen roller,
there may be a wood iller block insert for bracket
attachment. The wood block must be removed and
discarded before operation.
Case Installation
Pre-Installation
1. Carefully unpack case from shipping crate.
2. Set aside the Installation Kit. Items inside will be used during
installation.
3. Make sure to recheck measurement of case for proper
installation clearance.
4. Remove any protective foam from case.
5. If necessary, adjust hanger brackets with a 3/4" open wrench
or socket driver.
Remove
Bolt
White (Common)
Wire
Remove
Screw
Figure 1
Case Installation (continued)
5. Remove 2 screws to open junction box. Install electrical
connections that apply to your unit. Make sure to review the
wiring diagram for proper hook up. Replace junction box
cover and secure with 2 screws.
NOTE: Motor Operator Projection Screen Model WAD must
be installed in accordance with the requirements of the
Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA
70. An appropriate disconnect device shall be provided as
part of the building installation.
6. Test installation by running screen up and down a few times.
Be prepared to stop screen should any objects obstruct the
movement of the screen. To prevent damage to the motor,
the standard duty cycle is 2 minute 30 seconds on and 50
minutes of. For 230 volt motors 2 operating cycles is not to
be exceeded.
NOTE: Do not allow upper batten bar to come to a rest on
any object during travel. Doing so will cause cables to lose
tension.
7. The screen comes set standard with 18" of wire drop out of
the case.
Wood
Filler
Block
Produktspezifikationen
| Marke: | Da-Lite |
| Kategorie: | Projektionsleinwand |
| Modell: | Wireline Advantage 29454G |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Da-Lite Wireline Advantage 29454G benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Projektionsleinwand Da-Lite
7 April 2024
24 Februar 2024
6 Februar 2024
20 Januar 2024
5 Januar 2024
Bedienungsanleitung Projektionsleinwand
- Projektionsleinwand Sony
- Projektionsleinwand Pyle
- Projektionsleinwand Optoma
- Projektionsleinwand Celexon
- Projektionsleinwand Projecta
- Projektionsleinwand AV:link
- Projektionsleinwand Draper
- Projektionsleinwand Oregon Scientific
- Projektionsleinwand Duronic
- Projektionsleinwand Luxburg
- Projektionsleinwand EluneVision
- Projektionsleinwand Stewart
- Projektionsleinwand Elite Screens
- Projektionsleinwand Instaal
Neueste Bedienungsanleitung für -Kategorien-
2 Juni 2024
2 Juni 2024
25 Mai 2024
22 Mai 2024
21 Mai 2024
16 Mai 2024
14 Mai 2024