Da-Lite Senior Electrol Bedienungsanleitung

Da-Lite Projektionsleinwand Senior Electrol

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Da-Lite Senior Electrol (8 Seiten) in der Kategorie Projektionsleinwand. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

INSTRUCTION BOOK FOR

Senior Electrol®

Important Safety Instructions

When using your video equipment, basic safety precautions should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating

at least equal to that of the appliance should be used. Cords

rated for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric

shock when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by

the manufacturer may cause a risk of ire, electric shock, or

injury to persons.

Pre-Installation

Installation

1. Carefully unpack screen and remove outer wrapping

from case.

2. Remove instruction cover plate (Fig. 1). Do not remove metal

shipping brace (secures roller), wrapping paper, or tape strips

until screen is installed.

3. Make sure to recheck measurement of screen location

before installation.

NOTE: Screen is not centered in box. Screen surface

is set 18⅝" from motor end.

Ironing Board

Some Senior Electrols, depending on size and type of picture

surface, contain an ironing board to latten the fabric (long strip

attached). The ironing board is part of the screen. Do not remove

or alter (Fig. 2).

Hangers (If required)

1. Make sure one hanger is approximately 25" from end

of case (motor end).

2. Make sure second hanger is approximately 11 ½" from

opposite end of case.

3. Place a third hanger on the center line of fabric.

4. Make sure hangers are placed to it into notches provided

on screens equipped with an ironing board.

5. Make sure hanger used on motor end does not interfere

with motor access door.

Figure 2

Hex Head

Screws Tape Strip

Shipping

Brace

(Not on 3"

Roller) Ironing

Board

Wall Type Hanger

Picture

Surface

Picture

Surface

Picture Surface

Ceiling Type

Hanger

Rafters

Wall or Ceiling Mount With Hangers

Wall Type Hangers with ceiling hanger adapters are

standard equipment. For wall type, use wall hanger only.

For ceiling type installation, use the wall type hanger and

ceiling adapters as shown in Fig. 3 on page 4.

Recessed Above Ceiling

Other methods of installation will no doubt

suggest themselves especially in new buildings

where it would be an easy matter to provide a

recess for the screen to conceal it when not in use.

Do Not Seal In-Allow Access.

For Exposed Installation

If the screen is to be mounted in an exposed

position, it may be covered with inished plywood,

veneer paneling, plastic wall covering or a valance.

Figure 1

Instruction Cover

Case

Installation

Screen Adjustment

NOTE: Unit is not to be installed in air handling space.

1. Level unit lengthwise with a carpenter's level and plum

level.

CAUTION! Do not completely seal in unit. Access

room must be allowed for motor repair or fabric

replacement.

2. Remove shipping brace by removing 3 hex head screws

(Fig. 2).

CAUTION! Do not cut wrapping paper or tape with

knife or any sharp tool. Remove by hand.

3. Remove wrapping paper and tape strips (Fig. 2).

4. Install electrical hook up that applies to your unit. Make

sure to review your Electrical Installation Checklists and

wiring diagrams (included) for either 120 volt switch,

220/240 volt switch, or DRC low voltage control. Unit

should be installed by a qualiied electrician.

NOTE: Must be installed in accordance with the

requirements of the Local Building Codes, the Canadian

Electrical Code (CEC), CAN/CSA C22.1 and the National

Electric Code (NEC), NFPA 70.

5. Test installation by carefully running surface up and

down several times. Be prepared to stop screen.

6. Check for satisfactory condition by running screen a

few times.

NOTE: The picture surface, when rolled down, should

have a full wrap around the roller. Do not allow any part

of the roller to become exposed.

Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da-Lite.

Should it be necessary to adjust for more or less drop of picture (viewing area), proceed in the following manner:

More Screen Drop

1. Place operating switch in “down” position.

2. When the screen stops, turn the “down” limit knob one-

quarter turn clockwise.

3. Test by raising picture surface approximately two feet, then

lower again. Repeat until desired drop is attained.

CAUTION! When screen is in bottom position, do not

adjust for more than 3" of additional drop. Roller should

not be exposed.

Less Screen Drop

1. Raise picture surface approximately two feet above desired

level.

2. Place operating switch in position.“of”

3. Turn the “down” limit knob one-quarter turn

counterclockwise.

4. Test by raising and lowering picture surface.

5. Repeat steps 3 and 4 until desired drop is attained.

NOTE: Limit “down” switch knob controls stopping point of

picture surface in bottom position.

Limit “up” switch knob controls stopping point of picture surface

inside case.

Produktspezifikationen

Marke:	Da-Lite
Kategorie:	Projektionsleinwand
Modell:	Senior Electrol
Gewicht:	- g
Produktfarbe:	Weiß
Natives Seitenverhältnis:	4:3
Diagonal:	240 Zoll
Gesamte Bildschirmgröße (Höhe x Breite):	358 x 478 cm
Format:	Video
Leuchtdichtefaktor:	1
Gehäuse L1:	546 mm