CyberData Systems 011460 Bedienungsanleitung

CyberData Systems Telefon 011460

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CyberData Systems 011460 (3 Seiten) in der Kategorie Telefon. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

Quick Start Guide 931473A

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available in the Downloads tab at the following webpage:

http://www.cyberdata.net/voip/011460/

Note You can also navigate to the Downloads tab by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 15.4W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100Mbps

3 4

Part Number: 011460

SIP Weatherproof Keypad Phone

Quick Start Guide

The IP Endpoint Company

Quick Start Guide 931473A

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity above the

ethernet port on the board. See the following figure:

3.2. The amber 100 Mb Link LED blinks off once during the boot up process

when the device begins DHCP addressing and autoprovisioning attempts,

and then comes on again and remains constant (solid amber). The green

Link/Activity LED may be blinking depending on the network activity.

Note The default DHCP addressing timeout is 60 seconds. The device will attempt

DHCP addressing 12 times with a 3 second delay between tries and eventually

fall back to the programmed static IP address (by default 10.10.10.10) if DHCP

addressing fails. The DHCP Timeout is configurable in the device's Network

settings.

3.3. When the device has completed the initialization process, press and hold

the RESET switch (SW1 button) for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

100 Mb Link LED

Link/Activity J1

Quick Start Guide 931473A

4.0 Connecting to a Network in a Test Environment

Note The following connections are usually needed for this procedure:

• Computer

• PoE switch or injector

• CyberData device

4.1. In a test environment, use a computer that is connected to the same switch

as a single CyberData device. Note the subnet of the test computer.

4.2. Use the CyberData Discovery Utility program to locate the device on the

network. You can download the Discovery Utility program from the following

link:

http://www.cyberdata.net/assets/common/discovery.zip

4.3. Wait for initialization to complete before using the Discovery Utility program

to scan for a device. The device will show the current IP address, MAC

address, and serial number.

4.4. Select the device.

4.5. Click Launch Browser. If the IP address is in a reachable subnet from the

computer that you are using to access the device, the Discovery Utility

program should be able to launch a browser window pointing to the device’s

IP address.

4.6. Log on to the web interface by using the default username (admin) and

password (admin) to configure the device.

4.7. Perform an audio test by pressing the Test Audio button that is located at

the bottom of the Device Configuration page. If the audio test message is

clearly audible, then your CyberData device is functioning properly.

4.8. The device is now ready to be set for your desired network configuration.

You may search the Compatible IP-PBX Servers index for available

sample VoIP phone system configurations and set up guides at the following

website address:

http://www.cyberdata.net/connecting-to-ip-pbx-servers/

Produktspezifikationen

Marke:	CyberData Systems
Kategorie:	Telefon
Modell:	011460
Touchscreen:	Nein
Freisprecheinrichtung:	Nein
Anrufer-Identifikation:	Nein
WLAN:	Nein
Bluetooth:	Nein
Breite:	296 mm
Tiefe:	200 mm
Gewicht:	5400 g
Produkttyp:	IP-Telefon
Produktfarbe:	Black, Grey, Yellow
Internationale Schutzart (IP-Code):	IP66
Höhe:	409 mm
Betriebstemperatur:	-40 - 60 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 95 %
Paketgewicht:	6300 g
Hörertyp:	Kabelgebundenes Mobilteil
Schnittstellentyp Ethernet-LAN:	Schnelles Ethernet
Anzahl enthaltener Griffe:	1 Stück(e)
Sprachcodec:	G.711alaw, G.711ulaw, G.722
Zertifizierung:	CE; EMC Directive - Class A EN 55032 & EN 55024, LV Safety Directive- EN 60950-1, RoHS Compliant, FCC; Part 15 Class A, Industry Canada; ICES-3 Class A
Telefonbuch Kapazität:	- Eintragungen
Linienanzahl:	- Zeilen
Kurzwahlen:	Ja
Power over Ethernet (PoE):	Ja
Frontkamera:	Nein
Temperaturbereich bei Lagerung:	-40 - 70 °C
Geräuschunterdrückung:	Ja
Nachhaltigkeitskonformität:	Ja
Nachhaltigkeitszertifikate:	CE, RoHS
VoIP Protokolle:	SIP RFC 3261
Wandmontage:	Ja
Videoanruf:	Nein
Hüllenmaterial:	Edelstahl
Geeignet für Hörgeräte:	Ja
Ethernet/LAN:	Ja