CRUX RVCCH-75EC Bedienungsanleitung

CRUX Rückfahrkamera RVCCH-75EC

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CRUX RVCCH-75EC (7 Seiten) in der Kategorie Rückfahrkamera. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/7
RVCCH-75EC
Rear View Integration Interface
for CHRYSLER & DODGE Vehicles with 8.4” Screen
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
1 of 4
Adds reverse camera to the Uconnect Touchscreen Radio
Aermarket rear-view Camera included
Automacally switches to rear-view when car is in reverse gear
Plug & Play Installaon
PRODUCT FEATURES:
PARTS INCLUDED:
RVCCH-75EC Module RVCCH-75EC Harness CUB-01 Bullet Camera
INSTALLATION DIAGRAM:
WHITE Wire
Parking Guideline
DP
ON
DIP
SWITCH
LED* *LED RED = Power ON Status
LED BLUE = Data Bus ON Status
Regulator
20 Ft. Coax Cable
8-Pin Molex
Represents Solder Joint
TO RADIO
WHITE
22-PIN
(MALE)
GRAY
22-PIN
(MALE)
WHITE
22-PIN
(FEMALE)
GRAY
22-PIN
(FEMALE)
TO FACTORY
HARNESS
GROUND
WHITE Wire*
(Camera Power Output
+12V 250mA)
RED Wire
Tape O
(Not Used)
CUB-01 Camera
Included
*White wire does not supply Reverse Trigger on Manual Transmissions.
Camera power must be connected to factory reverse light wire instead.
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
2 of 4
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
DIP SWITCH SETTINGS:
INSTALLATION INSTRUCTIONS:
INSTALLING THE BULLET CAMERA AND CABLE
The kit includes a universal bullet camera that can be mounted in dierent ways. On way is to mount
it on the third brake light. Please see page 3 for installaon instrucons. Once the camera has been
installed, route the camera cable towards the radio.
INSTALLING THE RVCCH-75EC MODULE
Remove the radio to gain access to the connectors. Unplug the factory WHITE and GRAY connectors and
plug them into the WHITE and GRAY connectors of the RVCCH-75EC T-harness. Mate the YELLOW male
and female video RCAs of the RVCCH-75EC T-harness and the camera cable. Use the thin RED wire on
the camera cable to power the camera. Connect the thin RED wire to the WHITE wire on the RVCCH-
75EC harness. The RED wire near the camera is not used and needs to be insulated with tape. Connect
the BLACK ground wire near the camera to chassis ground. See diagram on page 1. Test the system for
funconality before reinstalling the radio.
DIP SWITCH FUNCTIONS:
DIP 1 = Set to OFF
DIP 2 = Rear View Camera ON / OFF
DIP 3 = Set to OFF
DIP 4 = Set to OFF
DIP 5 = Varies - Defaulted to OFF*
DIP 6 = Varies - Defaulted to OFF*
RVCCH-75EC
Rear View Integration Interface
for CHRYSLER & DODGE Vehicles with 8.4” Screen
*DIP 5 & 6
If the radio is having turn-on issues, please try the following:
Aempt 1: Set 5 & 6 to ON
Aempt 2: Set 5 to ON and 6 to OFF
Aempt 3: Set 5 to OFF and 6 to ON
1 2 3 4 5 6
ON
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
3 of 4
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCCH-75EC
Rear View Integration Interface
for CHRYSLER & DODGE Vehicles with 8.4” Screen
1. Remove the third brake light assembly. Use the supplied
drill saw and drill a hole on the back side of the third brake
light housing.
2. Connue drilling unl the pilot drill bit is visible on the
front side of the third brake light.
3. Turn over the third brake light assembly start drilling from
the front side. Carefully drill thru the red plasc lens.
4. Insert the camera cable and the camera thru the hole
but DO NOT FULLY INSERT. This will allow you to rotate the
camera to the right posion. Turn the ignion key to ON but
do not start the engine. Put the gear in reverse and check
the camera view. Adjust as necessary.
6. The CUB-01 bullet camera has parking guide lines that
can be turned ON or OFF. The parking guide line is defaulted
to ON from the factory. To turn OFF the parking guide lines,
cut the thin WHITE wire on the camera cable around 4 feet
away from the camera. Insulate with tape. Unplug the 4-pin
barrel connector near the thin WHITE wire. Align the arrows
on the 4 pin barrel connector and plug them together.
Make sure that the connectors are plugged in all the way.
5. Route the camera cable towards the radio/RVCCH-75EC
locaon.
INSTALLING THE CAMERA:


Produktspezifikationen

Marke: CRUX
Kategorie: Rückfahrkamera
Modell: RVCCH-75EC

Brauchst du Hilfe?

Wenn Sie Hilfe mit CRUX RVCCH-75EC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Rückfahrkamera CRUX

Bedienungsanleitung Rückfahrkamera

Neueste Bedienungsanleitung für -Kategorien-