CRUX RVCCH-75DC Bedienungsanleitung
CRUX
Rückfahrkamera
RVCCH-75DC
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CRUX RVCCH-75DC (6 Seiten) in der Kategorie Rückfahrkamera. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/6
RVCCH-75DC
Rear View Integration Interface with VIM
for DODGE RAM Trucks
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
1 of 3
• Adds reverse camera input to the Uconnect Touchscreen Radio
• Aermarket tailgate handle camera included
• Automacally switches to Rear-view when car is in Reverse mode
• Plug & Play Installaon
PRODUCT FEATURES:
PARTS INCLUDED:
RVCCH-75DC Module RVCCH-75DC Harness CDR-02 Camera
INSTALLATION DIAGRAM:
WHITE Wire
Parking Guideline
To Radio
OEM Radio
Harness
DP
ON
DIP
SWITCH
LED*
*LED RED = Power ON Status
LED BLUE = Data Bus ON Status
RVC Video
Signal Input
RED Wire Push in Connectors
all the way
Line up Arrows
Regulator
20 Ft. Coax Cable
RED Wire
Tape O
(Not Used)
BLACK
Wire
BLACK
(Ground)
8-Pin Molex Represents Solder Joint
Connect RCAs and secure
with tape all around
WHITE Wire
(Camera Power Output
+12V 250mA)
OR*
*Connect BLACK (ground) wire to chassis ground.
If video noise is present, we recommend connecting the
ground wire to the BLACK ground wire on the RVCCH-75DC harness.
Chassis Ground
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
2 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
DIP SWITCH SETTINGS:
INSTALLATION INSTRUCTIONS:
INSTALLING THE CDR-02 CAMERA AND CABLE
1. Remove the OE tailgate handle.
2. Remove the OE lock cylinder and install in the CDR-02 camera housing.
3. Install the new tailgate handle and run the cables to the radio.
4. Remove the factory radio to gain access to the factory connectors.
5. Route the wires towards the radio and make the power and video connecons. For powering up the camera, use the 12V
OUTPUT (White Wire). (See Wiring Diagram on page 1)
6. Connect the camera ground wire to chassis ground. If video noise is present, we recommend connecng a ground wire
from the camera to the BLACK wire on the RVCCH-75DC T-harness.
7. The CDR-02 has a built-in parking guide lines opon and is defaulted to ON from the factory. To turn OFF the parking guide
lines, cut the thin WHITE wire located on the camera cable 4 feet from the camera. Unplug the barrel connectors on the
cable for 10 seconds. Align the arrows on the barrel connectors and rmly plug them together.
8. Test the camera before re-installing the radio.
CODING THE RADIO FOR A REAR VIEW CAMERA
The radio has to be coded to accept a reverse camera. Please follow the coding procedure below:
1) Turn key o and remove the key from ignion.
2) Open the driver door then close it (make sure all doors, li gate and hood are also closed).
3) Look at the module and wait for LEDs to turn o then disconnect the module.
4) Before plugging back the module, turn all DIP switches to ON then OFF.
5) Set DIP switches to the sengs provided above.
6) Reconnect module and wait for the LEDs to turn o.
7) Start engine and the coding operaon is now complete.
8) Put the gear in reverse to test the camera.
DIP SWITCH FUNCTIONS:
DIP 1 = Set to OFF
DIP 2 = Rear View Camera ON / OFF
DIP 3 = Set to OFF
DIP 4 = Set to OFF
DIP 5 = Defaulted to OFF*
DIP 6 = Defaulted to ON*
RVCCH-75DC
Rear View Integration Interface with VIM
for DODGE RAM Trucks
*DIP 5 & 6
If the radio is having turn-on issues, please try the following:
Aempt 1: Set 5 & 6 to ON
Aempt 2: Set 5 to ON and 6 to OFF
Aempt 3: Set 5 to OFF and 6 to ON
1 2 3 4 5 6
ON
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
3 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCCH-75DC
Rear View Integration Interface with VIM
for DODGE RAM Trucks
VEHICLE APPLICATIONS:
RAM
2013 - 2017 1500
2013 - 2017 2500
2013 - 2017 3500
NOTES:
1. Not compable with diesel powered trucks.
2. Not compble with RAM trucks with factory installed cargo camera.
COMPATIBLE RADIOS:
8.4” Screen with Separate Knobs 5” Screen with 6 Buons &
Separate Knobs
4.3” Screen with 6 Buons &
2 Knobs
4.3” Screen with 4 Buons & 2 Knobs
Not compable radio
Produktspezifikationen
| Marke: | CRUX |
| Kategorie: | Rückfahrkamera |
| Modell: | RVCCH-75DC |
Brauchst du Hilfe?
Wenn Sie Hilfe mit CRUX RVCCH-75DC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Rückfahrkamera CRUX
16 August 2024
16 August 2024
15 August 2024
15 August 2024
14 August 2024
13 August 2024
13 August 2024
13 August 2024
12 August 2024
12 August 2024
Bedienungsanleitung Rückfahrkamera
- Rückfahrkamera AEG
- Rückfahrkamera Maginon
- Rückfahrkamera Conrad
- Rückfahrkamera MarQuant
- Rückfahrkamera Kenwood
- Rückfahrkamera Trebs
- Rückfahrkamera Dometic
- Rückfahrkamera Pyle
- Rückfahrkamera Pioneer
- Rückfahrkamera Garmin
- Rückfahrkamera Waeco
- Rückfahrkamera XOMAX
- Rückfahrkamera Beeper
- Rückfahrkamera Alpine
- Rückfahrkamera Pro User
- Rückfahrkamera XZENT
- Rückfahrkamera Clarion
- Rückfahrkamera Audiovox
- Rückfahrkamera DNT
- Rückfahrkamera Tracer
- Rückfahrkamera Hikvision
- Rückfahrkamera Furrion
- Rückfahrkamera Luis
- Rückfahrkamera Mobiset
- Rückfahrkamera Valeo
- Rückfahrkamera VDO Dayton
- Rückfahrkamera Veise
- Rückfahrkamera Valueline
- Rückfahrkamera Camos
- Rückfahrkamera CARMATRIX
- Rückfahrkamera Boyo
- Rückfahrkamera AutoXtreme
Neueste Bedienungsanleitung für -Kategorien-
19 September 2024
7 September 2024
7 September 2024
7 September 2024
7 September 2024
5 September 2024
3 September 2024
2 September 2024
2 September 2024
2 September 2024