Crown P.I.P.-FMX Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Crown P.I.P.-FMX (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
126589-1
10/98
Printed on
recycled paper.
P. I.P.–FMX
© 1998 by Crown International, Inc., P.O. Box 1000, Elkhart, IN 46515-
1000 U.S.A. Telephone: 219-294-8000. Fax: 219-294-8329.
P.I.P.
modules
are produced by the Professional Audio Division of Crown International,
Inc. Trademark Notice:
Crown
®,
Macro-Tech
®,
Com-Tech
®,
IOC
® and
P.I.P.
® are registered trademarks of Crown International, Inc. Other
trademarks are the property of their respective owners.
P.I.P.-FMX
Page 2
Fig. 1.1 PIP-FMX
1 Welcome
Thank you for purchasing the
Crown® P.I.P.-FMX accessory.
P.I.P.® modules are designed to
quickly install in the rear panel of
many Crown amplifiers. P.I.P.
stands for “Programmable Input
Processor.” Their versatile fea-
tures expand the capabilities of
your amplifier and enable you to
customize it for your particular
needs.
FMX means Female and Male
XLRs to signify that the unit uses
female and male XLR connectors
for “daisy chain” input/output.
Features
❏3-pin female XLR connectors
are provided for input.
❏3-pin male XLR connectors are
provided for daisy chaining the
input to other amplifiers.
❏Male or female connectors can
be used for input or daisy
chaining since they are wired in
parallel.
❏The ¼-inch phone jack inputs
can also be used for daisy
chaining other amplifiers
equipped with ÂĽ-inch inputs
(such as the Macro-Tech® se-
ries).
❏The XLR connectors are wired
with pin 1 as the signal ground
(shield), pin 2 as a noninverted
input (+), and pin 3 as an in-
verted input (–).
P.I.P.-FMX
Page 3
2 Installation
You may need a Phillips screw-
driver to remove the existing
P.I.P.
module or panel from your ampli-
fier.
CAUTION: Before connecting this
or any
P.I.P.
to your amplifier, it is
important to turn the amplifier’s
level controls down, turn it off and
remove the AC power. Don’t touch
the circuitry. Even though the am-
plifier is off, there could still be
enough energy remaining to
cause electric shock.
1. Turn down the level controls (full
counterclockwise), turn off the
amplifier and unplug it from the
AC power source.
2. Remove the existing
P.I.P.
mod-
ule or panel (two screws). For
PIP2
amplifiers, this may involve
disconnecting the
P.I.P.
from a
PIP2
input adapter (see Figures
2.2 and 2.3). If a
PIP2
input
adapter is already present, do
not remove the ribbon cables
from the adapter. Otherwise you
will have to reconnect them in
the next step.
3.
Standard P.I.P. Amplifiers
: Align
the edges of the
P.I.P.–FMX
in
the
P.I.P.
card rails and firmly
push the unit in until it is seated
against the mounting bracket
(see Figure 2.1).
PIP2 Amplifiers:
(Requires a
PIP2
input adaptor, Crown part num-
ber Q43528-1.) Connect the
PIP2
input adapter to the two
input cables of the amplifier (see
Figure 2.2). Notice that the
PIP2
input adapter should be posi-
tioned with the
P.I.P.
edge con-
nector on top and facing away
from the amplifier. The 20-pin
cable (A) is connected first, then
the 18-pin cable (B) is con-
nected. Both ribbon cables
should extend below the
PIP2
input adapter.
P.I.P.
MODULE
BACK PANEL
OF AMPLIFIER
Fig. 2.1 Installation into a
Standard P.I.P. Amplifier
Fig. 2.2 PIP2 Input Adapter
Connection
A
B
B
A
18 PIN (B)
20 PIN (A)
PIP2 ADAPTER
FROM AMPLIFIER
Next, insert the edge connector
of the
P.I.P.–FMX
into the
PIP2
input adapter (see Figure 2.3)
and insert the assembly into the
P.I.P.
opening in the back of the
amplifier.


Produktspezifikationen

Marke: Crown
Kategorie: Nicht kategorisiert
Modell: P.I.P.-FMX

Brauchst du Hilfe?

Wenn Sie Hilfe mit Crown P.I.P.-FMX benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Crown

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-