Crestron Saros ICS8T-W-T-EACH Bedienungsanleitung

Crestron Subwoofer Saros ICS8T-W-T-EACH

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Crestron Saros ICS8T-W-T-EACH (2 Seiten) in der Kategorie Subwoofer. Dieser Bedienungsanleitung war für 32 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Saros® 8” Subwoofer In-Ceiling Speakers

quickstart guide

SAROS ICS8T

www.crestron.com

Specifications subject to

change without notice.

SAROS ICS8T

Mount or Remove Speaker

The in-ceiling speaker includes four toggle clamps that simplify the mounting process. If the grille is

mounted on the speaker, remove it before proceeding. (Refer to “Install or Remove Grille,” above.)

1. Referring to the illustrations to the right, remove the screw securing the rear cover panel, and lift

the cover panel off to expose the supplied terminal block.

2. Route the speaker cable through the cover cable clamp and connect the wires to the terminal

block, using the outer IN terminals: red to + and black to –. Use the inner + and – THRU terminals

to connect a pass-through (parallel) speaker.

3. Allow some slack in the speaker cable(s) and position the cover panel on the back, making certain

it engages the mounting clips. Secure the cover panel using the screw removed in step 1, and

tighten the cable clamp to secure the cable(s). Do not overtighten. Use a safety tether attached to

the rear enclosure to prevent the speaker from accidentally falling.

4. The toggle clamps offer two positions to accommodate both standard and extra thick surfaces up

to 2.4 in (61 mm). For extra thick tiles, reset the toggle clamps to the upper position before

continuing.

a. With the toggle clamps turned inward, insert the speaker into the opening.

b. Hold the speaker against the ceiling and begin tightening the four screws on the front of the

speaker. The toggle clamps first rotate into clamping position (as indicated in the front view

illustration to the right), and then begin holding the speaker to the ceiling.

c. Tighten the screws until the speaker is secure. Do not overtighten.

5. Speaker removal is accomplished by reversing steps 1 through 4 above.

Set the Transformer Tap Selector Switch

The speakers are equipped with a 70/100 V matching transformer for distributed audio

systems. The transformer tap selector switch on the front panel is used to set the speaker

power level. Use a flat blade screwdriver to adjust the switch.

• For SAROS ICS8T 70 V systems, use the left-side settings, and select 60 or 120

watts.

• For SAROS ICS8T 100 V systems, use the right-side settings, and select 120 watts.

The X position should not be used.

The switch may also be set to 8 Ω operation, bypassing the transformer completely. This

setting should be used only for 8 Ω audio systems.

1Installation

Saros® speakers by Crestron® deliver professional-grade performance

and flexible installation in a range of popular sizes for demanding

commercial applications. Solid construction, easy installation, and

high-end components are hallmarks of the Saros speaker line.

Ideal for use in background or foreground music, paging, and sound

reinforcement systems, Saros speakers are engineered to achieve

smooth, even coverage, high output, and clear, natural sound quality.

The SAROS ICS8T model is an 8-inch, in-ceiling subwoofer designed

to extend the low frequency response of Crestron’s full range Saros

speakers. It is intended for use with Crestron’s AMP-series

Commercial Power Amplifiers, which can provide low impedance or

70/100 V distributed power to the Saros speaker line. Because of the

internal crossover, no biamping is required.

SAROS ICS8T subwoofers are available in white or black and may be

painted to blend with the ceiling surface.

Prepare Mounting Hole

Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air ducts, joists,

or other possible obstructions. If applicable, use a good quality stud finder to locate joists. If there are

no obstructions, use the supplied template to trace an outline of the mounting hole.

For drop tile ceilings, remove the ceiling tile and place on a flat surface to trace the mounting hole. For

drywall or standard construction ceilings, use the template to trace the mounting hole directly on the

ceiling.

Install Cable

Run the cable from the audio source to the speaker location, observing all appropriate local codes.

Strip the ends of the speaker cables approximately 1/8 in to 3/16 in (~3 mm to ~5 mm) and, if the cable

is stranded, twist the strands.

Install Tile Bridge

The included tile bridge components provide proper support when the speaker is installed in a typical

drop tile ceiling. Refer to the illustration below.

1. Based on the location of the mounting hole determined in “Prepare Mounting Hole” (above), use

the two supplied screws to attach the support ring to the rails so that when installed, the ring is

aligned with the mounting hole and the rails rest on the ceiling grid frame.

2. Adjust the support ring position as necessary to enable off-center speaker positioning. The tile

bridge assembly can be folded to fit through the speaker cutout in blind-mount situations.

Install or Remove Grille

The zero-bezel frameless grille is held in place by powerful magnets. A safety tether is included to

prevent any possibility of the grille falling from the speaker above. With the tether attached, place the

grille in position on the speaker. To remove the grille, grip the edges and pull away from the speaker.

Paint the Speaker Grille

Speaker grille painting should be done prior to mounting.

1. Carefully remove the material on the underside of the grille, and set it aside for reinstallation. It

may be necessary to use a knife or other sharp instrument to free an edge of the material so it

can be peeled away. Use care to avoid cutting or tearing the material.

2. Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the holes in the

grille.

Tile Bridge Assembly

20.91 in

(531 mm)

Support

Ring

Screws

(Supplied)

25.92 in

(659 mm)

Terminal Block

Not Shown

Screw

Cable Clamp

Speaker

Cable

Terminal

Block

Rear Cover

Panel

Speaker Cable Connections

Screw

100V70V

120

THRU

Front View (Grille Removed)

Tighten

Screws

70V 100V

120

QUICKSTART DOC. 7494C (2037421) 12.17

The specific patents that cover Crestron products are listed at patents.crestron.com.

Certain Crestron products contain open source software. For specific information, please visit

www.crestron.com/opensource.

Crestron, the Crestron logo, and Saros are either trademarks or registered trademarks of Crestron

Electronics, Inc., in the United States and/or other countries. Other trademarks, registered

trademarks, and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Crestron disclaims any proprietary interest in the marks

and names of others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

QUICKSTART DOC. 7494C (2037421) 12.17

Saros® 8” Subwoofer In-Ceiling Speakers

quickstart guide

SAROS ICS8T

www.crestron.com

Specifications subject to

change without notice.

SAROS ICS8T

3Specifications

SAROS ICS8T Specifications

The following table provides corrective action for possible trouble situations. If

further assistance is required, please contact a Crestron customer service

representative.

Further Inquiries

To locate specific information or resolve questions after reviewing this guide,

contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876] or,

for assistance within a particular geographic region, refer to the listing of Crestron

worldwide offices at www.crestron.com/offices.

To post a question about Crestron products, log onto Crestron’s Online Help at

www.crestron.com/onlinehelp. First-time users must establish a user account to

fully benefit from all available features.

Future Updates

As Crestron improves functions, adds new features, and extends the capabilities

of the SAROS ICS8T, additional information may be made available as manual

updates. These updates are solely electronic and serve as intermediary

supplements prior to the release of a complete technical documentation revision.

Check the Crestron website periodically for manual update availability and its

relevance. Updates are identified as an “Addendum” in the Download column.

TROUBLE

POSSIBLE CAUSE(S)

CORRECTIVE ACTION

No sound or

intermittent

sound is

coming from

the speaker.

There is a cable

connection error.

Verify the cable connections

between the amplifier and

speaker.

The amplifier is not

receiving an input signal,

or there is a malfunction.

Verify that the amplifier is

functioning correctly, that it is

receiving an input signal, and

that the correct input source

is selected.

There is a faulty device

in the system.

Verify that all system devices

are functioning properly.

Constant noise

such as buzz,

hum, or hiss is

coming from

the speaker.

There is a system

grounding fault.

Verify that system grounding is

correct.

Poor low

frequency

output.

There is an incorrect

polarity connection at

the speaker or amplifier.

Verify speaker connection

polarity ( on amplifier to on + +

speaker).

4Problem Solving

Troubleshooting

2Physical Views

Rear and Side Views

TH RU

Recommended

Cutout Diameter

Diameter

Minimum

Mounting Depth

Front View (Grille Removed)

120

SPECIFICATION DETAILS

Woofer

8 in (203 mm) polypropylene with rubber surround, steel basket, and phase plug

Impedance

8 Ω nominal with transformer set to 8 Ω

Transformer Taps

60 watts or 120 watts at 70 V; 120 watts at 100 V

Input Frequency Range

20 Hz to 20 kHz

Internal Low-Pass Filter

125 Hz, 2

order

Acoustic Frequency

Response

45 Hz to 125 Hz (±3 dB)

Acoustic Frequency Range

35 Hz to 125 Hz (-10 dB)

Power Handling

100 watts program (8 Ω)

Sensitivity

90 dB @ (1W/1m)

Connection 4-pin, 5 mm detachable terminal block with screw-down anges;

Speaker input with parallel pass-through;

Maximum wire size: 12 AWG

Controls

Transformer Tap Recessed screwdriver-adjustable rotary switch on bafe;

Used to select 70/100 V tap settings or 8Ω (bypass)

Environmental

Temperature

-2° to 120° F (-19° to 49° C)

Humidity

5% to 95% RH (noncondensing)

Construction

Enclosure

Zinc-plated steel, plenum-rated, 1/2 in or 3/4 in conduit knockout top and side

Bafe

ABS UL94V-0 plastic

Grille Steel with textured nish, paintable, magnetically held, zero-bezel frameless design,

safety tether included

Mounting Flush ceiling mount using four integral 2-step toggle clamps, 2.4 in (61 mm)

maximum surface thickness, tile bridge included; two rigging points for safety tether,

(SPKA-ST-15, sold separately)

Dimensions

Diameter

12.07 in (307 mm) not including toggles

Depth

9.10 in (231 mm)

Recommended cutout

diameter

11.20 in (285 mm)

Minimum mounting

depth

8.90 in (226 mm)

Weight

14.0 lb (6.4 kg)

Produktspezifikationen

Marke:	Crestron
Kategorie:	Subwoofer
Modell:	Saros ICS8T-W-T-EACH

Brauchst du Hilfe?

Wenn Sie Hilfe mit Crestron Saros ICS8T-W-T-EACH benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Subwoofer Crestron

Crestron Saros PDS8T-W-T-EACH Bedienungsanleitung

21 August 2024

Crestron SAROS ICS8T-B-T-EACH Bedienungsanleitung

20 August 2024

Crestron Vector SUBS15 Bedienungsanleitung

20 August 2024

Crestron Vector SUBD18 Bedienungsanleitung

20 August 2024

Crestron Vector SUBS18 Bedienungsanleitung

20 August 2024

Crestron SAROS PDS8T-B-T-EACH Bedienungsanleitung

19 Dezember 2023

Crestron Saros ICS8T-W-T-EACH Bedienungsanleitung

7 Juli 2023

Bedienungsanleitung Subwoofer

Neueste Bedienungsanleitung für -Kategorien-

Pioneer S-21W Bedienungsanleitung

13 Oktober 2024

JL Audio SGR-10TW3 Bedienungsanleitung

13 Oktober 2024

Polk DB1040 Bedienungsanleitung

10 Oktober 2024

Blaupunkt GBW801 Bedienungsanleitung

7 Oktober 2024

JL Audio TW1 Bedienungsanleitung

6 Oktober 2024

Jensen J12W Bedienungsanleitung

6 Oktober 2024

Musway MT169Q Bedienungsanleitung

6 Oktober 2024

JL Audio 12W0v3 Bedienungsanleitung

4 Oktober 2024

Yamaha YST-SW315PN Bedienungsanleitung

2 Oktober 2024

JBL SW10 Bedienungsanleitung

30 September 2024