Coolaroo Shade Sail Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Coolaroo Shade Sail (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
E V E R Y D A Y
C O M M E R C I A L G R A D E & E V E R Y D A Y
A S S E M B L Y G U I D E
c o o l a r o o . c o m
Installing your new Coolaroo Shade Sail is simple,
following our step-by-step instructions.
Available shapes and sizes
Triangle
Triangle
RectangleSquare
Square
Size
5m x 5m x 5m
6.5m x 6.5m x 6.5m
Size
3m x 3m x 3m
3.6m x 3.6m x 3.6m
Size
5m x 3m
Size
5.4m x 5.4m
Size
3m x 3m
3.6m x 3.6m
How our Shade Sails are made
Our Shade Sails are made using
quality HDPE fabric suitable for the
harsh Australian climate.
Your Coolaroo Shade Sail comes
with stainless steel buckles on
each corner. Measurements of
our Shade Sails are taken from
buckle to buckle along the nominal
straight line of the Shade Sail.
C O M M E R C I A L G R A D E
SHADE SAIL
B E F O R E Y O U S T A R T !
Building approval
It is important to check prior to installation
for any relevant building regulations with
your local authorities (council).
Selecting the location
Before installing your Shade Sail,
consider what your needs are.
Factors which should be taken into account are:
Strength of existing structures
intended to be anchor points
– Ability to insert xing posts
Location of barbecues, electrical / telephone
cables, water / sprinkler pipes, etc.
– Water run-o
– Sun direction
There could also be other factors, specic to
your situation, which require consideration.
Shade Sail installations
If you require assistance in regards to
your specic installation, please consult
a qualied builder or engineer.
Note: It is important when deciding on the
positioning of the sail lower point, that the slope
of the fabric will allow good water run-o. Water
which is allowed to pond on the sail will lead to
premature sail failure and may lead to structural
failure at xing points. It is recommended
to have the Shade Sail on a 10
+ slope.
To achieve the style, two corners hyperbolic
are required to be at high points and two
corners at low points. (Image a.)
To achieve the style, two corners resort
are required to be at high points and one
corner at a low point. (Image b.)
Determining suitable
xing points
Aer deciding on the location of your Coolaroo
Shade Sail it is important to identify structurally
suitable xing points for the sail corners. This stage
is critical. Your sail will be under signicant tension
and as such xing points need to be strong. It is
recommended that the xing height be at least
2.4m from the ground on 2 of the sides. Allow 10%
of the sail length between each xing point and
the corner D Rings for tensioning. Consider using
stainless steel chain to reach certain xing points.
If using existing xtures, such as side fascia
or the roof of your house, be sure to check
the structure carefully to ensure it can bear
the load. If unsure about the most suitable
xing points, obtain independent advice
from a qualied builder or engineer.
Aer identifying the most suitable xing points,
lay the sail out on the ground in the proposed
position to conrm the positioning is workable.
There is an extensive range of Coolaroo xing
accessories available to help you secure your
sail (refer to Shade Sail accessories table).
Low
Low
HighHigh
Low
High
High
Fixing points
Utilising existing supports
If you intend to x your sail to a fascia, the use
of a fascia support is strongly recommended.
The fascia support will reinforce the overhangs
of raers or trusses and provide a stronger
connection between the two. Fascia supports
are available from your local hardware store.
Fascia support
Raer/
truss
Raer/truss
Fascia
support
b.
a.
Posts
Note: It is not recommended to use a tree for a
sail xing.
Post lengths should be calculated taking
into account the proposed height of your
sail plus the depth of your footings.
It is recommended to use galvanised or painted
posts to prevent rust. Steel posts are available
from your local hardware store or steel supplier,
and can be cut to predetermined lengths and
colour-matched to your sail environment. and
It is recommended to use a round steel post
with a minimum diameter of 90mm, or a
90x90mm square steel post. Post wall thickness
Alternatively, the use of treated sowood (H5 level
treatment) or Hardwood of durability Class 1 is also
suitable. The timber post should be a minimum
125mm in diameter. Your local timber supplier
can assist you in your selection. (Image d.)
It is advisable to lean posts at an angle of 5 (
50mm
per 1m of pole height), sloping away from the centre
of the sail for additional support. (Image e.)
5°
90mm90mm
125mm125mm
Treated timber posts
Footings for your Shade Sail
All posts should be embedded in concrete
footings with a minimum 20 MPa.
Measure out centres of the footing positions
and mark locations. (Image f.)
400mm
5m size or larger Shade Sails
400mm
400mm
1200mm
c.
d.
e.
Dig holes to the required size for your posts
height, using the centre of the footing as the
approximate locations of the point of the sail.
For a 3m size sail dig footing holes 400mm
square and 800mm deep (Image g.)
For a 5m or larger sail dig footing holes 400mm
square and 1200mm deep (Image h.)
Conditions vary for dierent environments; if
unsure of the concrete type best suited to your
area contact your local concrete supplier. Mix
the concrete to the manufacturer’s instructions,
these should be clearly labelled on the packet.
f.
g.
h.


Produktspezifikationen

Marke: Coolaroo
Kategorie: Nicht kategorisiert
Modell: Shade Sail

Brauchst du Hilfe?

Wenn Sie Hilfe mit Coolaroo Shade Sail benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Coolaroo

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-