Chord VGW1 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Chord VGW1 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
VGW1
VHF Guitar Wireless System
Item ref: 171.848UK
User Manual
Version 1.3
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
171.848UK User Manual
Introduction:
Thank you for choosing the Chord F-series wireless system. This professional wireless set provides an instrument VHF VH
radio system for freedom of movement without loss of audio quality. Please read this manual before using this equipment
in order to avoid damage through incorrect operation and to get the best performance from your purchase.
Contents:
Please take care when unpacking this product. Inspect for any damage and ensure you have the following components…
• VHF wireless receiver
• Mains power adapter
• 6.3mm to 3.5mm instrument jack lead
• 6.3mm mono jack lead
• 9V battery, PP3
Warning:
To prevent the risk of fire or electric shock, do not expose any of the components to rain or moisture.
If liquids are spilled on any component, stop using immediately, allow unit to dry out and have checked by qualified
personnel before further use.
Avoid impact or heavy vibration to any of the components.
No user serviceable parts inside transmitter or receiver - refer servicing to qualified service personnel.
Safety
• Ensure that the correct adapter is used with adequate current rating and that the mains voltage is as stated on the
adapter.
• Avoid ingress of water or particles into the transmitter(s) or receiver
• Use alkaline or NiMH batteries in the transmitter(s) and remove if unused for long periods.
• Observe the correct polarity when replacing batteries
Placement
• Keep all components out of direct sunlight and away from heat sources.
• Do not place heavy objects on top of the receiver or transmitter(s)
• If rack-mounting, secure the receiver to a 1U rack tray and do not place heavy equipment above the receiver.
• Keep the transmitter(s) and receiver away from damp or dusty environments.
Cleaning
• Use a soft cloth with a neutral detergent to clean the body of the beltpack transmitter and receiver.
• Lightly damp sterile wipes may be used on the beltpack for hygiene purposes
• To avoid damage, do not use solvents to clean the components
171.848UK User Manual
Beltpack Transmitter
Receiver Rear Panel
Receiver Front Panel
Operation
To begin, insert batteries into the transmitter. Slide the front half of the beltpack upwards just enough to reveal the
battery compartment and position the supplied 9V battery inside (ensure + and - are the correct way around) and then
slide the beltpack case together as before.
Position the receiver within the best available line of sight to the transmitter(s) and connect the DC jack of the supplied
power adapter to the receiver and the plug-top to the mains outlet. Extend both antennas fully upwards and outwards
slightly and switch the power on. Turn the output level down on the receiver.
Connect the jack or XLR (optional) lead to the receiver’s audio output connector, turn down the volume of the guitar
amplifier (or effect unit) that the signal will be fed into and then connect the jack or XLR to the guitar amplifier.
Move the slide switch on the beltpack transmitter to the first notch (MUTE) e LED should light momentarily –th
(continuous dim LED indicates low battery). Move on another notch (ON) and gradually increase the output level on the
receiver, then increase the volume on the guitar amplifier until the sound from the guitar can be heard through the amp
(ensuring guitar volume controls are turned up)
If the wireless system is not to be used for more than a few seconds, it is preferable to slide the transmitter switch to the
“OFF” position, which mutes and deactivates the radio signal and powers down the transmitter. Be sure to turn down the
volume of th guitar amplifier and then switch off the receiver. e
Unplug signal leads from the receiver and mixer or amplifier when moving or packing away.
If the system is not to be used for long periods of time, remove the batteries from the transmitter and unplug the power
adapter from the receiver and the mains outlet. Retracting the antennae can also help avoid damage when the system is
not in use.
1. GAIN ADJUST rotary control
2. and Slide switch LED
3. Guitar input (3.5mm jack)
1. Antennas
2. DC Power input
3. Unbalanced 6.3mm jack output
4. Balanced XLR output
1. Power ON/OFF switch
2. POWER indicator LED
3. SIGNAL indicator LED
4. VOLUME control


Produktspezifikationen

Marke: Chord
Kategorie: Nicht kategorisiert
Modell: VGW1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Chord VGW1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Chord

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-