Chord Huei Bedienungsanleitung

Chord Empfänger Huei

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Chord Huei (3 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 34 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/3
Chord Electronics
Product Communication | English
_
The Pumphouse Farleigh Lane,
East Farleigh, Maidstone
ME16 9NB United Kingdom
info@chordelec tronics.co.uk
chordelectronics.co.uk
Huei
Manual
_
V.2.0
chordelectronics.co.uk
_
Operation 3.0
Chord Electronics
Huei | Manual
_
Eliminating ground/earth hum
Turntables can experience unwanted hum or buzzing related to grounding
issues from the cartridge. Huei allows you to ground your turntable using a
convenient grounding post, situated above the ‘IN R’ and ‘IN L’ RCA posts.
You should always use the post to ground your device and eliminate noise.
To ground your cartridge, unscrew the locking earth-pin (we recommend
three turns) and locate the earthing wire from your turntable. Place the
spade tip in between the metal washers and hex bolt, before screwing back
the locking earth-pin thumb-tight. While a spade tip is recommended, if
you have bare wire, you can wrap this around the post and then secure the
locking earth-pin. Please also read Grounding plate (3.0)
Important information
Only connect Huei to a device capable of attenuating its output, such as
a preamplifier or integrated amplifier. Do not connect Huei directly to a
power amplifier. Incorrect settings could cause irreparable damage to your
equipment and hearing.
If you need support, in the first instance, please contact your supplying
retailer who will be best placed to assist you. If you need additional help
beyond that of your retailer, please visit our support page: chordelectronics.
co.uk/get-support
Connecting Huei to your preamplifier or amplifier
Moving Magnet gain ranges:
Colour V Gain dB - RCA Output V Gain dB - XLR Output
Output
22 dB 28 dB
Max Gain 42 dB 48 dB
37 dB 43 dB
32 dB 38 dB
30 dB 36 dB
25 dB 31 dB
23 dB 29 dB
21 dB 27 dB
Removing rumble noise
Huei features a Rauch Slope rumble filter that removes mechanical noise
from the turntable. It cancels out the opposing noise from each channel
whilst keeping the original music signal intact. To engage the filter, press
‘RUMBLE’ until the sphere shows white. If no colour is displayed, the rumble
filter is ‘o’.
OFF ON
Specifications
Input impedance MM 47,000 Ω
Input impedance MC 100 - 3700 (12-step)Ω Ω
Input noise 1.1n V/Hz
Max output voltage 20 V RMS
Equalisation response RIAA curve
Equalisation accuracy ± 0.1 dB
Frequency response RIAA curve 12 Hz to 25 kHz
Dimensions 41 mm (H) x 160 mm (W) x 72 mm (D)
Weight 657 g
Placement
Always ensure Huei is used in a well-ventilated setting, away from direct
sunlight and heat sources, and has sucient space around the unit.
Chord Electronics’ Qutest Stand System (available separately) has been
designed to perfectly house Huei. Otherwise, care should be taken not to
stack other units on Huei.
Only operate
within the specified
temperatures
Never drop or expose
Huei to mechanical
shock.
Only use a dry cloth to
gently clean Huei.
Never directly spray
liquids, including
cleaners, onto Huei.
Do not allow Huei to
come into contact with
liquid.
No user-serviceable
parts contained. Do not
disassemble Huei.
Never poke objects
into the exposed
connectors.
5°C 40°C
41°F 104°F
Care instructions
The Pumphouse Farleigh Lane, East Farleigh,
Maidstone, ME16 9NB United Kingdom
MADE IN THE UNITED KINGDOM chordelectronics.co.uk
Operation 3.0
General operation and
important information
1.0
Chord Electronics
Huei | Manual
_
Setting LED brightness
It’s possible to adjust the brightness of the control spheres between two
modes: ‘high’ and ‘low’. To cycle between the modes, simply press both the
‘MM/MC’ and the ‘RUMBLE’ buttons simultaneously.
Power connection
Huei is supplied with a 12 V, 2A external power supply (which is the only supply
that should be used). A convenient power switch above the 12 V DC input, can
be used to switch Huei ‘on’ and ‘o’. We recommend that this is performed with
partnering preamps or amplifiers turned ‘o’.
Connecting turntables to Huei
Huei has one stereo pair of RCAs for connection to turntables. These inputs
are labelled as ‘IN R’ (right channel) and ‘IN L’ (left channel) and are colour-
coded to facilitate connections to turntables.
Connecting Huei to your preamplifier or amplifier
Huei features variable gain to attenuate the volume for high-output
cartridges. Use the chart below to adjust the gain to a suitable level for your
preamp or amplifier. Do not adjust the gain while a signal is going through
the device. If you are unsure of which setting is appropriate, consult your
dealer. Please note that the light range will repeat after it has fully cycled.
Moving Coil gain ranges:
Grounding plate
The gold-plated grounding plate, pictured, is preinstalled for your
convenience. It is required for headshells/tonearms that do not provide
a ground for both RCA connectors. It is safe to leave this in place for
normal use, however if you are using Huei with a turntable with balanced
connections then please remove the plate.
Introduction
Welcome to Huei, a high-performance Moving Magnet and Moving Coil
phono stage proudly developed and manufactured by Chord Electronics
in Kent, England. Please take a few moments to familiarise yourself with its
operation.
Connections and controls 2.0
Rear
Front
Rumble filter on/o Cartridge gain
selector button
Balanced XLR right
and left output
Grounding postUnbalanced RCA
right and left output
Balanced/
unbalanced RCA
right
and left input
12 V DC power
input
Moving Magnet and
Moving Coil selector
button
Cartridge impedance
selector button
Connecting turntables to amplifiers
Huei has two outputs: RCA and XLR. We recommended using one output at
a time. As the circuitry within Huei is fully balanced, XLR may be preferable.
To connect Huei to the amplifier/preamp, ensure that all devices are turned
‘o’ before securely attaching interconnects to Huei and the partnering
amplifier, paying attention to the L (left) and R (right) channel markers.
To
preamp
From
turntable
To
preamp
Please note that the impedance of the cartridge may not fit exactly within the
ranges specified; select the range that best matches. Selecting an impedance
with a 2.2uF load when using a Moving Coil (MC) cartridge dampens the ringing
of lower impedance cartridges, reducing distortion.
NOTE: IMPEDANCE CANNOT BE CHANGED WHEN IN MOVING MAGNET MODE. PRESS AND
HOLD THE MM/MC BUTTON TO ACTIVATE MOVING COIL MODE. WARNING! PLEASE MUTE
OR LOWER THE VOLUME OF YOUR PREAMPLIFIER BEFORE CHANGING IMPEDANCE.
Max Gain 70 dB 76 dB
Colour V Gain dB - RCA Output V Gain dB - XLR Output
Output
64 dB 70 dB
60 dB 66 dB
Selecting MM or MC playback
When setting up Huei for playback, it is most important to correctly
identify and select the type of cartridge you’ll be using from the cartridge
manufacturer’s specifications. Both Moving Magnet (MM) and Moving Coil
(MC) have unique specifications and subsequently, dierent custom settings
are available within Huei’s menu.
150 + 2.2 Ω
µ
F 100 100 Ω Ω + 2.2
µ
F
Once Huei is connected, do not switch your preamp/amplifier ‘on’ until the
volume is at its lowest setting. Next, turn Huei ‘on’ and select the appropriate
settings for your cartridge as explained below. With the settings correct,
select the lowest gain setting on Huei (white), before turning connected
equipment ‘on’.
Next, select the appropriate input on your preamplifier, begin playing the
source and gradually increase the gain/volume to a comfortable level.
Please note that if Huei is switched ‘o’, it will remember previously selected
settings. You should only need to complete the set-up of your cartridge
during the initial installation (unless you change cartridge).
Selecting the impedance setting for your cartridge
It is only possible to select impedance with a Moving Coil cartridge in MC
mode (Moving Magnets always require a set 47 k impedance). Therefore, Ω
when in Moving Magnet mode, the ‘IMPEDANCE’ button will not illuminate.
With a Moving Coil cartridge in MC mode, select the correct impedance from
information within the manufacturer’s specifications. If you cannot identify
the impedance information from your cartridge user manual or relevant
website, please consult your supplying dealer or the manufacturer directly.
Once the impedance of the cartridge is known, use the graphical guide
below to find a suitable match and select the corresponding colour by
pressing the ‘IMPEDANCE’ button repeatedly. The impedance will increase
sequentially to Min + 2.2 uF before moving back down the range again.
MOVING MAGNET (MM) MOVING COIL (MC)
To select between Moving Magnet (MM) and Moving Coil (MC), press and
hold the ‘MM/MC’ button until the corresponding colour is selected for your
input.
3700 3700 + 2.2 Ω Ω
µ
F 1000 Ω
1000 + 2.2 Ω
µ
F 470 Ω
470
Ω + 2.2
µ
F
320 320 Ω Ω + 2.2
µ
F 150 Ω 50 dB 56 dB
58 dB 64 dB
52 dB 58 dB
51 dB 57 dB
49 dB 55 dB

Produktspezifikationen

Marke: Chord
Kategorie: Empfänger
Modell: Huei

Brauchst du Hilfe?

Wenn Sie Hilfe mit Chord Huei benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Empfänger Chord

Chord

Chord CPA 2500 Bedienungsanleitung

3 September 2024
Chord

Chord CB-15BT Bedienungsanleitung

28 August 2024
Chord

Chord CG-10BT Bedienungsanleitung

28 August 2024
Chord

Chord Qute HD Bedienungsanleitung

28 August 2024
Chord

Chord Ultima 3 Bedienungsanleitung

20 August 2024
Chord

Chord CPA 5000 Bedienungsanleitung

12 August 2024
Chord

Chord SPM 5000 MkII Bedienungsanleitung

6 August 2024
Chord

Chord SPM 1400 Mk2 Bedienungsanleitung

3 August 2024
Chord

Chord 2yu Bedienungsanleitung

3 August 2024
Chord

Chord CPM 3350 Bedienungsanleitung

30 Juli 2024

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024
Denon

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024
Pro-Ject

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024
AKG

AKG HP12U Bedienungsanleitung

15 Oktober 2024
Sennheiser

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024
Yamaha

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024
JL Audio

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024
Pioneer

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024
Technics

Technics SA-160L Bedienungsanleitung

8 Oktober 2024
Avantree

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024