Chord CPA 2500 Bedienungsanleitung

Chord Receiver CPA 2500

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Chord CPA 2500 (12 Seiten) in der Kategorie Receiver. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
welcome
Thank you for buying a Chord product.
Before you start to enjoy using to your Chord product, please take a couple of minutes to read how to connect your audio
equipment and loudspeakers to your pre-amplifier or integrated amplifier and how to maximise your listening experience.
user guide for CPA 2500 pre-amplifier
The pre-amplifier is the control centre of your system. By connecting your audio sources to it you can choose the source you
want at any particular time and control it.
You can also adjust the balance and volume before the signal is sent to a power amplifier. Your pre-amplifier can be
operated manually or via the Chord remote control.
background
We want you to be confident using your new Chord amplifier.
You’re probably an audiophile with extensive knowledge of audio equipment. However, you may not be!
So in the following section we explain a few basics to help you get started, or get you back up to speed if you’re a little rusty.
connecting your equipment
Chord amplifiers are supplied with and designed to be connected using balanced inputs. The interconnecting cables you use will
depend on the available input and output sockets on your other equipment. We have installed unbalanced inputs on all Chord
equipment, thus enabling you to mix Chord and other manufacturer’s equipment. Whichever cable you choose it is important
to make sure it is fully screened to avoid any noise problems.
Balanced inputs carry twice the strength of signal of unbalanced inputs and are able to be fed down long lengths
of cable with less deterioration of signal. They are also less prone to interference than unbalanced inputs.
Balanced inputs have three pins and use Neutric XLR style connectors. Pin 1 is earth, pin 2 is positive and pin 3
is negative.
Unbalanced inputs use RCA phono connectors which are gold plated with teflon high performance
dielectric insulators for optimum performance.
Speakers
Power Amplifier
or integrated
amplifier
Pre-amplifier
Audio Source
when setting up
To ensure that your Chord integrated amplifier works efficiently and safely, please pay particular attention to the following
issues.
ventilation
Your Chord integrated amplifier should have at least 5cm of clear space all around it to ensure a free flow of air at all times.
When driven continuously at well above average levels, the temperature at the back of the unit may exceed 50ºC. This is
normal and no cause for concern, although it does highlight the need for adequate ventilation around the unit. We recommend
that you do not place your integrated amplifier directly on a carpet.
mains lead and plug
All Chord equipment comes supplied with the correct mains lead and plug. This should be used at all times.
if you need to fit a plug for UK/Europe
Connect the blue wire to the neutral terminal Connect the
brown wire to the live terminal Connect the yellow/green
wire to the earth terminal
if you need to fit a plug for US/Canada
Connect the white wire to the neutral terminal
Connect the black wire to the live terminal Connect
the green to the earth terminal
earthing issues in Europe
In some European countries a hum may occur if your integrated/pre-amplifier is connected to mains sockets that do not have an
earth. If this is the case please ensure that:
1. Your integrated/pre-amplifier is connected via a multi-way mains block which contains an earth point at each socket outlet.
This is to ensure that the chassis metalwork of each item is connected together.
2. Use the connecting points on your Chord unit and connect to an available earth point.
3. We recommend that an earthing method for your building is implemented.
safety warnings
It is important that your integrated/pre-amplifier is earthed at all times via its own mains lead. Failure to do this may be
hazardous. The power supply components within the amplifier are designed to be operated at lethal voltages and energy levels.
Circuit designs that embody these components conform with applicable safety requirements. Precautions must be taken to
prevent accidental contact with power-line potentials. Do not connect grounded test equipment.
These units comply with EN 50081-1 and IEC 801/2

Produktspezifikationen

Marke: Chord
Kategorie: Receiver
Modell: CPA 2500

Brauchst du Hilfe?

Wenn Sie Hilfe mit Chord CPA 2500 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Receiver Chord

Bedienungsanleitung Receiver

Neueste Bedienungsanleitung für -Kategorien-