Chief SLM290 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Chief SLM290 (1 Seiten) in der Kategorie Projektorzubehör. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-
mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The
information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the
information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
© 2007 Chief Manufacturing, 8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-000153
9/28/07
SLB-290 and SLM-290 Interface Brackets
for ASK C20, C60, INFOCUS LP-280, LP-290
SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling
1-800-582-6480.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation:
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.
1. Screw three thumb screws onto three 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the three nylon spacers over the three threaded inserts in the bottom of the projector
4. Place the interface bracket onto the three nylon spacers in the bottom of the projector lining up the three holes in the bracket with the three
threaded inserts in the bottom of the projector.
5. Using the three M4 X 20mm mounting screws, start them into the mounting holes by hand and secure all three fasteners at this time.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
(1) Interface Bracket (3) SPACER, Nylon, .50" x .190" x .50"
(3) 10-24 Thumb Nuts ** (3) SCREW, Flat head, M4 x 20mm
(1) All-Points Security Kit
**Only used when installing SLB Interface brackets.
SLB-290
SLM-290
Towards front of
Towards front of
Projector
Projector


Produktspezifikationen

Marke: Chief
Kategorie: Projektorzubehör
Modell: SLM290

Brauchst du Hilfe?

Wenn Sie Hilfe mit Chief SLM290 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Projektorzubehör Chief

Bedienungsanleitung Projektorzubehör

Neueste Bedienungsanleitung für -Kategorien-