Chief FSM4100 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Chief FSM4100 (2 Seiten) in der Kategorie Unterstützung für Flachbildschirme. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
8804-000046 RevA 2/28/07
CHIEF MANUFACTURING INC. 1-800-582-6480, Fax: 1-877-894-6918, Email: chief@chiefmfg.com
INSTALLATION INSTRUCTIONS
FSM SERIES
SMALL FLAT PANEL DISPLAY STATIC WALL MOUNT
Exclusive Q2™ Mounting System
Prior to assembly, unpack carton completely and verify contents.
If you are missing any of the following components, Service at 1-800/582-6480 please contact Customer
(1) FSM Wall Bracket (4) Drywall Anchor
(2) Wood Screw (4) Washer, Flat, .25 ID X .56 OD
BEFORE PROCEEDING, READ INSTALLATION INSTRUCTIONS COMPLETELY
BEFORE PROCEEDING, READ INSTALLATION INSTRUCTIONS COMPLETELY
WARNING: IMPROPER INSTALLATION MAY RESULT IN SERIOUS PERSONAL INJURY!
When mounting Chief Manufacturing accessories, the structural system and mounting method
MUST be capable of supporting 5 times the combined weight of the total installation. The maximum
weight to be installed on the FSM is 45 pounds (20.4 Kg) in wood stud and 30 pounds (13.60 kg) in
drywall.
Flat Panel Displays are Extremely Fragile.
If Monitor Uses a Screw Size Other Than M4 X 10mm (M4 X 20mm),
DO NOT USE M4 Screws Provided. Monitor Damage Could Occur.
Interface Bracket Installation:
1. See installation procedures accompanying your mounting bracket.
Optional Latching Flag Placement:
1. Remove Phillips head screw, Nylock nut and latching flag (see Figure 2).
2. Reposition latching flag and secure using Phillips head screw, Nylock nut.
CAUTION!
Figure 1
Remove screw
and nut
Figure 2
Move latch
CAUTION!
Minimum Sheetrock Thickness ½ Inch.
Drywall Installation Procedures:
1. Using the wall bracket as a template at the desired mounting location, mark the location of the four
outer mounting holes.
2. Using a 3/8-inch drill, drill four pilot holes
to a minimum depth of 1 1/2”
at the locations marked in
Step 1.
3. Install an anchor bolt in one of the pilot holes and tighten anchor bolt until it is fully seated (see
Figure 3).
4. Remove and retain bolt from anchor and repeat Step 3 and 4 for three remaining anchor bolts.
5. Install .25 ID X .56 OD flat washer on each of four bolts removed from anchors.
6. Using four bolts, with washers installed, secure wall bracket to wall.
Wood Stud Installation Procedures:
1. Locate stud and, using wall bracket as a template at the desired height, mark the location of the two
center mounting holes.
2. Install a flat washer on each of the two wood screws.
3. Using the two wood screws with flat washers installed, secure wall bracket to wall.
Mounting Display with Interface Bracket to Wall Bracket:
1. Make sure the latching flag on the mounting bracket is in the unlocked position (see Figure 4).
2. Place your small flat panel display; with interface bracket attached, onto the wall bracket, making
sure it is securely seated.
3. Lower the latching flag on the wall bracket, locking small flat panel display in place (see Figure 5).
Figure 4 Figure 5
Locke
d
CAUTION!
Outer Mountin
g
Holes
Figure 3
%%c0.375
(
PREDRILL HO LE
)
INSERT ANCHOR INTOPPREDRILLED HOLE
CW
A
NCHOR BARBP
(
STOPS ANCHOR ROTATIO N
)
#10-24 Screw O 0.375 (Predrill Hole)
Insert anchor into
predrilled hole
Anchor Barb
(Stops anchor rotation)
Ancho
r
Turn 10-24 screw clockwise
until anchor fully seats
against back side of wall
CW
Unlocke
d
Center Mounting Holes


Produktspezifikationen

Marke: Chief
Kategorie: Unterstützung für Flachbildschirme
Modell: FSM4100

Brauchst du Hilfe?

Wenn Sie Hilfe mit Chief FSM4100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Unterstützung für Flachbildschirme Chief

Bedienungsanleitung Unterstützung für Flachbildschirme

Neueste Bedienungsanleitung für -Kategorien-